Do you build bulkheads around ducting in Edmonton?

Yes — bulkheads and soffits to box in ductwork, plumbing and lighting are part of nearly every basement frame.

Should basement framing touch the concrete?

No. That puts wood and insulation against a cold and sometimes damp surface with no way to dry. The wall is held off, or a rigid layer goes on the concrete first. It costs an inch of floor and saves a musty basement.

Can the same crew do the drywall after framing in Edmonton?

Yes — one crew frames, boards, tapes and finishes, so nothing gets lost in a handoff between trades.

Do you coordinate with my electrician and plumber?

Yes — we sequence the framing so your other trades can rough in cleanly before insulation and drywall.

Why does framing matter for the drywall finish?

Because the finish inherits the frame. A bowed stud or a wall out of plumb cannot be made flat with compound. Every problem left in the framing becomes a finishing problem and then a visible one.

What is crowning a stud?

Sighting each stud and setting them all with the bow facing the same way so the wall plane is consistent. Studs set randomly give a wall that waves, and in an Edmonton room with a window running along it that shows through the paint.

Framing Edmonton | Emplastrum

Framing in Edmonton, square and ready for drywall

Turning an unfinished basement or an open floor plan into real rooms starts with the frame. In Abbottsfield, Albany, Alberta Avenue, Aldergrove, Allard, Allendale we build wood-frame basement development layouts and interior partition walls — squared, plumbed and spaced for the drywall going over them. We frame interior, non-load-bearing walls only; a licensed structural engineer handles anything load-bearing. Abbottsfield, Albany, Alberta Avenue, Aldergrove, Allard, Allendale is an older Edmonton community where settling cracks, aging texture and the occasional plaster repair come up, so framing here often means reworking walls that have shifted or been altered over the decades, alongside basement development. The same crew that frames can board, tape and finish too, so there is no handoff between trades. We cover Abbottsfield, Albany, Alberta Avenue, Aldergrove, Allard, Allendale and Edmonton, 7 days a week.

Wood-frame basement development layouts in Abbottsfield, Albany, Alberta Avenue, Aldergrove, Allard, Allendale
Frame-to-finish: one crew frames, boards, tapes and finishes
Door rough openings framed to spec
Bulkheads and soffits for ductwork and lighting
Stud spacing matched to the drywall going over it
Abbottsfield, Albany, Alberta Avenue, Aldergrove, Allard, Allendale coverage — we come to you
Interior partition walls framed square and plumb

Layout for the sheet, not just for the room

Where the joints will land

Framing at the right spacing and adding backing where a sheet edge will fall means the board has something to fasten to at every joint.

Butt joints

An unsupported butt joint in an Edmonton wall is the hardest thing in drywall to hide. Thinking about sheet layout at framing stage removes them, and it costs nothing but attention.

Why Edmonton homeowners trust Emplastrum for framing

Framed by the people who finish it

As a drywall and finishing company first, we frame walls the way we want to board and tape them — square, plumb and consistent — because no amount of mud hides a crooked frame in Edmonton.

Fixed price, same-day reply

We cover Edmonton, Abbottsfield, Albany, Alberta Avenue, Aldergrove, Allard, Allendale and Edmonton, 7 days a week. Free on-site quotes and fixed prices, and we stand behind the work.

Load-bearing walls and where we stop

Not our decision to make

Removing or altering a wall that carries load is a structural question, and we do not take a homeowner's assurance that a wall is non-bearing.

What we need

Drawings or an engineer's assessment. If a wall in an Edmonton renovation turns out to be bearing, the job becomes beams and posts — a different scope, and one far better priced before demolition than discovered during it.

Basement development framing in Abbottsfield, Albany, Alberta Avenue, Aldergrove, Allard in Edmonton, Allendale

From open concrete to real rooms

A basement development layout is the most common framing job we do in Abbottsfield, Albany, Alberta Avenue, Aldergrove, Allard, Allendale — bedrooms, a bathroom, a media room or a suite, framed to plan and ready for the trades that follow.

Interior and non-load-bearing only

We keep our framing to interior, non-load-bearing walls and bulkheads. Anything structural belongs with a licensed structural engineer — and we will tell you honestly when that is what your project needs.

Common framing situations in Abbottsfield, Albany, Alberta Avenue, Aldergrove, Allard in Edmonton, Allendale

Basement layouts

An older Edmonton community where settling cracks, aging texture and the occasional plaster repair come up, so framing an unfinished basement into a usable layout is the call we hear most.

Partition changes

We also reframe and add partition walls in Abbottsfield, Albany, Alberta Avenue, Aldergrove, Allard, Allendale homes when a layout changes — closing an opening, splitting a room, or adding a closet or storage wall.

Bulkheads, and why they are never straight by accident

Boxing what has to stay

Edmonton basements are full of ducts, beams and plumbing that cannot move. Bulkheads box them, and each one adds corners.

Getting them right

A bulkhead framed slightly out of square is obvious once it is boarded, because the eye follows its long lines. They take longer than their size suggests and they are worth the extra care.

How it works

Simple, clean, on schedule — Framing in Edmonton

Free quote

We come out to your Edmonton property, take a real look at the framing, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every framing quote in Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the framing in Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Edmonton home while we finish the framing to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished framing with us and you're happy with the result in Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the framing contractor Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your framing project in Edmonton.

Read our reviews on Google

FAQ — Framing Edmonton

Framing Edmonton: your questions answered

Do you build bulkheads around ducting in Edmonton?: Yes — bulkheads and soffits to box in ductwork, plumbing and lighting are part of nearly every basement frame.
Should basement framing touch the concrete in Edmonton?: No. That puts wood and insulation against a cold and sometimes damp surface with no way to dry. The wall is held off, or a rigid layer goes on the concrete first. It costs an inch of floor and saves a musty basement.
Can the same crew do the drywall after framing in Edmonton?: Yes — one crew frames, boards, tapes and finishes, so nothing gets lost in a handoff between trades.
Do you coordinate with my electrician and plumber?: Yes — we sequence the framing so your other trades can rough in cleanly before insulation and drywall.
Why does framing matter for the drywall finish in Edmonton?: Because the finish inherits the frame. A bowed stud or a wall out of plumb cannot be made flat with compound. Every problem left in the framing becomes a finishing problem and then a visible one.
What is crowning a stud?: Sighting each stud and setting them all with the bow facing the same way so the wall plane is consistent. Studs set randomly give a wall that waves, and in an Edmonton room with a window running along it that shows through the paint.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Framing

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Framing Edmonton

Framing in Edmonton, square and ready for drywall