Can you take out this wall?

Only once we know it is not load-bearing, and that needs drawings or an engineer rather than an assumption. If it is bearing, the job becomes beams and posts — far better priced before demolition than discovered during it.

Can the same crew do the drywall after framing in Lee Ridge?

Yes — one crew frames, boards, tapes and finishes, so nothing gets lost in a handoff between trades.

Steel studs or wood in a basement?

Often a mix — steel for long partition runs where straightness matters, wood where cabinets and heavy fixings are going. Steel will not warp or rot; wood takes fasteners anywhere. We will say which we would use where.

Do you frame basement developments in Lee Ridge?

Yes — wood-frame basement layouts ready for drywall are our most common framing job. We also cover Bisset, Crawford Plains, Daly Grove and Mill Woods and Meadows.

Do you coordinate with my electrician and plumber?

Yes — we sequence the framing so your other trades can rough in cleanly before insulation and drywall.

Can you add backing for a TV mount and shelves?

Yes, and tell us before the wall closes. Adding backing while it is open takes minutes; finding it missing afterwards means opening the wall or relying on anchors that eventually pull out. We ask what is going on the walls first.

Framing Lee Ridge Edmonton | Stud Walls

Basement and partition framing in Lee Ridge

Wood-frame basement development layouts in Lee Ridge
Bisset, Crawford Plains, Daly Grove coverage — we come to you
Interior partition walls framed square and plumb
Lee Ridge coverage — we come to you
Door rough openings framed to spec
Bulkheads and soffits for ductwork and lighting
Stud spacing matched to the drywall going over it

Basement framing against foundation walls in Edmonton

Hold it off the concrete

Framing tight against an Lee Ridge foundation wall puts wood and insulation against a cold, sometimes damp surface with no way to dry.

How it is done

The wall is held off, or a rigid layer goes on the concrete first. It costs an inch or two of floor space and it is the difference between a basement that stays dry and one that smells musty in year two.

Lee Ridge drywall in context

About Lee Ridge

Lee Ridge, named for Robert Lee (Mayor of Edmonton, 1909 - 1910), is one of the 27 neighbourhoods of Mill Woods.

What we see in Lee Ridge

In Lee Ridge the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Why Lee Ridge homeowners trust Emplastrum for framing in Edmonton

Framed by the people who finish it

As a drywall and finishing company first, we frame walls the way we want to board and tape them — square, plumb and consistent — because no amount of mud hides a crooked frame in Bisset, Crawford Plains, Daly Grove.

Fixed price, same-day reply

We cover Bisset, Crawford Plains, Daly Grove and Mill Woods and Meadows, 7 days a week. Free on-site quotes and fixed prices, and we stand behind the work.

Backing for everything that gets fixed later

Decide before it closes

Grab bars, TV mounts, floating shelves, cabinets, handrails and towel rails all need something solid behind the board.

The cheap moment

Adding backing while the Lee Ridge wall is open takes minutes. Finding it missing after the wall is finished means opening it or relying on hollow-wall anchors that eventually pull out. We ask what is going on the walls before we close them.

Steel studs against wood in a Lee Ridge basement

Different tools for different jobs

Steel is straight, will not warp, does not burn and does not rot, which suits a basement or a shop. Wood takes fasteners anywhere and is easier for backing and heavy fixings.

How we choose

Often a mix — steel for the long partition runs where straightness matters, wood where cabinets and heavy items are going. We will say which we would use where and why.

Bulkheads, and why they are never straight by accident

Boxing what has to stay

Lee Ridge basements are full of ducts, beams and plumbing that cannot move. Bulkheads box them, and each one adds corners.

Getting them right

A bulkhead framed slightly out of square is obvious once it is boarded, because the eye follows its long lines. They take longer than their size suggests and they are worth the extra care.

What affects the cost of framing in Lee Ridge in Edmonton?

Wall length, layout and openings

Framing cost in Lee Ridge tracks the total wall length, the complexity of the layout, and the number of openings and bulkheads. We price off a site walk-through and give a fixed number before we start.

Typical framing work in Lee Ridge homes

Because Lee Ridge is a Mill Woods and Meadows community with a mix of older homes and newer builds, framing calls here range from clean basement layouts in the newer homes to alteration work in the older ones.

How it works

Simple, clean, on schedule — Framing in Lee Ridge Edmonton

Free quote

We come out to your Lee Ridge Edmonton property, take a real look at the framing, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every framing quote in Lee Ridge Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the framing in Lee Ridge Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Lee Ridge Edmonton home while we finish the framing to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished framing with us and you're happy with the result in Lee Ridge Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the framing contractor Lee Ridge Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your framing project in Lee Ridge Edmonton.

Read our reviews on Google

FAQ — Framing Lee Ridge Edmonton

Framing Lee Ridge Edmonton: your questions answered

Can you take out this wall?: Only once we know it is not load-bearing, and that needs drawings or an engineer rather than an assumption. If it is bearing, the job becomes beams and posts — far better priced before demolition than discovered during it.
Can the same crew do the drywall after framing in Lee Ridge in Edmonton?: Yes — one crew frames, boards, tapes and finishes, so nothing gets lost in a handoff between trades.
Steel studs or wood in a basement?: Often a mix — steel for long partition runs where straightness matters, wood where cabinets and heavy fixings are going. Steel will not warp or rot; wood takes fasteners anywhere. We will say which we would use where.
Do you frame basement developments in Lee Ridge?: Yes — wood-frame basement layouts ready for drywall are our most common framing job. We also cover Bisset, Crawford Plains, Daly Grove and Mill Woods and Meadows.
Do you coordinate with my electrician and plumber?: Yes — we sequence the framing so your other trades can rough in cleanly before insulation and drywall.
Can you add backing for a TV mount and shelves?: Yes, and tell us before the wall closes. Adding backing while it is open takes minutes; finding it missing afterwards means opening the wall or relying on anchors that eventually pull out. We ask what is going on the walls first.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Framing

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Framing Lee Ridge Edmonton

Basement and partition framing in Lee Ridge