Do you frame basement developments in Kensington?

Yes — wood-frame basement layouts ready for drywall are our most common framing job. We also cover Albany, Athlone, Baranow and Northwest.

Do you build bulkheads around ducting in Kensington?

Yes — bulkheads and soffits to box in ductwork, plumbing and lighting are part of nearly every basement frame.

Do you coordinate with my electrician and plumber?

Yes — we sequence the framing so your other trades can rough in cleanly before insulation and drywall.

Can the same crew do the drywall after framing in Kensington?

Yes — one crew frames, boards, tapes and finishes, so nothing gets lost in a handoff between trades.

Can you take out this wall?

Only once we know it is not load-bearing, and that needs drawings or an engineer rather than an assumption. If it is bearing, the job becomes beams and posts — far better priced before demolition than discovered during it.

Can the same crew do the drywall after framing in Kensington?

Yes — one crew frames, boards, tapes and finishes, so nothing gets lost in a handoff between trades.

Framing Kensington Edmonton | Stud Walls

Framing in Kensington, set out for the board that follows

Frame-to-finish: one crew frames, boards, tapes and finishes
Kensington coverage — we come to you
Bulkheads and soffits for ductwork and lighting
Albany, Athlone, Baranow coverage — we come to you
Wood-frame basement development layouts in Albany, Athlone, Baranow
Interior partition walls framed square and plumb
Stud spacing matched to the drywall going over it

Our Kensington framing process in Edmonton, step by step

Layout before lumber

We chalk the plate lines from the plan or your walk-through direction and confirm every wall location in your Albany, Athlone, Baranow space before anything is cut.

Square, plumb, spaced right

We frame the walls square and plumb with stud spacing matched to the board going over them — the frame stage is where a wavy wall gets built or avoided. See our basement drywall work in Albany, Athlone, Baranow for the stage that follows.

Kensington drywall in context

About Kensington

Kensington was annexed to the City in 1913 during a real estate boom but most development didn't occur until the 1950s.

What we see in Kensington

In Kensington the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Crowning studs and checking for bow

Every stud has a curve

Lumber is rarely straight. Crowning means sighting each stud and setting them all with the bow facing the same way so the wall plane is consistent.

What happens without it

Studs set randomly give a wall that waves in and out, and in an Kensington room with a window running along it, that shows through the finished paint no matter how good the taping.

Backing for everything that gets fixed later

Decide before it closes

Grab bars, TV mounts, floating shelves, cabinets, handrails and towel rails all need something solid behind the board.

The cheap moment

Adding backing while the Kensington wall is open takes minutes. Finding it missing after the wall is finished means opening it or relying on hollow-wall anchors that eventually pull out. We ask what is going on the walls before we close them.

Bulkheads, and why they are never straight by accident

Boxing what has to stay

Kensington basements are full of ducts, beams and plumbing that cannot move. Bulkheads box them, and each one adds corners.

Getting them right

A bulkhead framed slightly out of square is obvious once it is boarded, because the eye follows its long lines. They take longer than their size suggests and they are worth the extra care.

Basement framing against foundation walls in Edmonton

Hold it off the concrete

Framing tight against an Kensington foundation wall puts wood and insulation against a cold, sometimes damp surface with no way to dry.

How it is done

The wall is held off, or a rigid layer goes on the concrete first. It costs an inch or two of floor space and it is the difference between a basement that stays dry and one that smells musty in year two.

Layout for the sheet, not just for the room

Where the joints will land

Framing at the right spacing and adding backing where a sheet edge will fall means the board has something to fasten to at every joint.

Butt joints

An unsupported butt joint in an Kensington wall is the hardest thing in drywall to hide. Thinking about sheet layout at framing stage removes them, and it costs nothing but attention.

How it works

Simple, clean, on schedule — Framing in Kensington Edmonton

Free quote

We come out to your Kensington Edmonton property, take a real look at the framing, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every framing quote in Kensington Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the framing in Kensington Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Kensington Edmonton home while we finish the framing to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished framing with us and you're happy with the result in Kensington Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the framing contractor Kensington Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your framing project in Kensington Edmonton.

Read our reviews on Google

FAQ — Framing Kensington Edmonton

Framing Kensington Edmonton: your questions answered

Do you frame basement developments in Kensington?: Yes — wood-frame basement layouts ready for drywall are our most common framing job. We also cover Albany, Athlone, Baranow and Northwest.
Do you build bulkheads around ducting in Kensington?: Yes — bulkheads and soffits to box in ductwork, plumbing and lighting are part of nearly every basement frame.
Do you coordinate with my electrician and plumber?: Yes — we sequence the framing so your other trades can rough in cleanly before insulation and drywall.
Can the same crew do the drywall after framing in Kensington in Edmonton?: Yes — one crew frames, boards, tapes and finishes, so nothing gets lost in a handoff between trades.
Can you take out this wall?: Only once we know it is not load-bearing, and that needs drawings or an engineer rather than an assumption. If it is bearing, the job becomes beams and posts — far better priced before demolition than discovered during it.
Can the same crew do the drywall after framing in Kensington in Edmonton?: Yes — one crew frames, boards, tapes and finishes, so nothing gets lost in a handoff between trades.

Need Edmonton’s go-to drywall contractor for repair, restoration and finishing? One trusted team for boarding, taping, finishing, repairs & renovations — start to finish.

Your Drywall Contractor in Edmonton →

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Framing

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Framing Kensington Edmonton

Framing in Kensington, set out for the board that follows