Will you block my soffit vents?

No. Baffles hold the insulation back at the eaves so air can still move from the soffits to the ridge. A blocked attic gets damp no matter how much insulation is in it.

Should I block the vents to stop drafts?

No. The attic is meant to run close to outdoor temperature so the roof deck stays cold. Blocking soffit vents causes exactly the ice damming people add insulation to prevent.

Do you insulate the attic hatch too?

Yes. It is a direct opening between the house and a space at outdoor temperature, and it is usually the first place we look when someone says a hallway or landing is cold.

How much insulation should my Whitemud Edmonton attic have?

The depth comes from what the code asks for on your permit, not from us. What we can tell you is the depth you have now, whether it is even, and whether the eaves and hatch are dealt with — those three often matter more than the last few inches.

How much insulation should my attic have?

It is settled depth and even coverage that decide performance, not the product name. We set depth markers before blowing so the result is measurable, and check the corners rather than just the area near the hatch.

Attic Insulation Whitemud Edmonton

Blown-in attic insulation in Whitemud Edmonton, sealed before it is filled

The most common mistake in an Whitemud Edmonton attic is blowing insulation over an unsealed ceiling. Warm moist air keeps rising through pot lights, top plates and the hatch, and it carries moisture into cold insulation where it condenses. We air-seal the penetrations first, then insulate.

Baffles kept clear so the soffit vents still breathe
Blown-in loose-fill to the depth your permit specifies
Air sealing at pot lights, top plates and the attic hatch
Existing insulation levelled before the top-up
Attic hatch insulated and weatherstripped
Depth markers left in place so the result is verifiable

Depth is the whole number

What you are buying

Attic performance is almost entirely a function of settled depth and even coverage. Two attics with the same product can perform very differently.

How we handle it

Depth markers are set before blowing so the result is measurable rather than asserted, and the Whitemud Edmonton attic is checked at the corners rather than only where the hatch is. An attic that is deep in the middle and thin at the perimeter is the usual finding.

The attic hatch, which everybody forgets

A hole in the ceiling

The hatch in an Whitemud Edmonton home is often an uninsulated panel sitting in a frame with no weatherstrip. It is a direct opening between the house and a space that is at outdoor temperature.

What we do

The hatch gets insulated on its back face and weatherstripped so it seals when closed. It is a small job that shows up disproportionately in comfort, and it is the first place we look when someone says the hallway is cold.

Ventilation is not optional up there

Cold attic, by design

An Whitemud Edmonton attic is meant to run close to outdoor temperature so the roof deck stays cold and snow does not melt and refreeze at the eaves.

The failure it prevents

Blocking soffit vents with insulation causes exactly the ice damming people add insulation to prevent. Air sealing the ceiling below and keeping the vents clear are two halves of the same job.

Adding to what is already there

You rarely start empty

Most Whitemud Edmonton attics already have something, whether old batts, older loose fill, or both in layers.

When to top up and when not

If the existing material is dry, even and uncontaminated, adding over it is usually the best value. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we say which one we found.

The attic hatch nobody insulates

A hole in the ceiling

An uninsulated, unsealed hatch is a direct opening between the heated house and a cold attic, and it is often the single worst detail in an otherwise good Whitemud Edmonton ceiling.

Simple fix

An insulated cover with weatherstripping and a dam around the opening so blown insulation does not spill through when it is opened.

What we can and cannot tell you about savings

Honest about the number

We will not quote you a percentage off your heating bill. It depends on your current depth, your air leakage, your windows, your furnace and how you heat the house.

What we will say

What the attic has now, what it would have after, and where the leaks are. Those are things we can measure and show you. A savings figure from a contractor who has not seen your utility bills is a sales number, not an estimate.

How it works

Simple, clean, on schedule — Attic Insulation in Whitemud Edmonton

Free quote

We come out to your Whitemud Edmonton property, take a real look at the attic insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every attic insulation quote in Whitemud Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the attic insulation in Whitemud Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Whitemud Edmonton home while we finish the attic insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished attic insulation with us and you're happy with the result in Whitemud Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the attic insulation contractor Whitemud Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your attic insulation project in Whitemud Edmonton.

Read our reviews on Google

FAQ — Attic Insulation Whitemud Edmonton

Attic Insulation Whitemud Edmonton: your questions answered

Will you block my soffit vents?: No. Baffles hold the insulation back at the eaves so air can still move from the soffits to the ridge. A blocked attic gets damp no matter how much insulation is in it.
Should I block the vents to stop drafts?: No. The attic is meant to run close to outdoor temperature so the roof deck stays cold. Blocking soffit vents causes exactly the ice damming people add insulation to prevent.
Do you insulate the attic hatch too?: Yes. It is a direct opening between the house and a space at outdoor temperature, and it is usually the first place we look when someone says a hallway or landing is cold.
Can I add over the old insulation?: Usually yes, if it is dry, even and uncontaminated. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we tell you which one we found.
How much insulation should my Whitemud Edmonton attic have?: The depth comes from what the code asks for on your permit, not from us. What we can tell you is the depth you have now, whether it is even, and whether the eaves and hatch are dealt with — those three often matter more than the last few inches.
How much insulation should my attic have?: It is settled depth and even coverage that decide performance, not the product name. We set depth markers before blowing so the result is measurable, and check the corners rather than just the area near the hatch.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Attic Insulation Whitemud Edmonton

Blown-in attic insulation in Whitemud Edmonton, sealed before it is filled

Attic Insulation Whitemud Edmonton

Depth is the whole number

What you are buying

How we handle it

Attic Insulation in every Whitemud Edmonton community

Where we work in Whitemud Edmonton

The attic hatch, which everybody forgets

A hole in the ceiling

What we do

Ventilation is not optional up there

Cold attic, by design

The failure it prevents

Adding to what is already there

You rarely start empty

When to top up and when not

The attic hatch nobody insulates

A hole in the ceiling

Simple fix

What we can and cannot tell you about savings

Honest about the number

What we will say

Simple, clean, on schedule — Attic Insulation in Whitemud Edmonton

Free quote

Book a day

The work

Walk it with you

Rated by Edmonton Homeowners

Attic Insulation Whitemud Edmonton: your questions answered

Attic Insulation in every Whitemud Edmonton community

Estimate Your Insulation

How much do you need?

Want it quoted properly?