Do I need to seal before adding insulation?

Yes, and it is the part most often skipped. Warm moist air leaking from the house frosts the roof deck and wets the insulation. Blowing over unsealed pot lights and top plates buries the problem instead of fixing it.

I store things in my attic. Can I keep doing that?

Yes, but the plywood squashes the insulation beneath it to joist depth. Either the storage area gets raised on a platform above the finished depth, or it stays as a deliberately weaker zone kept small. We will not top up around it and pretend it is not there.

How do I know I got the depth I paid for?

We leave depth markers through the attic so the installed depth can be read off by anyone afterwards. Depth is easy to claim and hard to check once the hatch is closed, which is exactly why we mark it.

Will you block my soffit vents?

No. Baffles hold the insulation back at the eaves so air can still move from the soffits to the ridge. A blocked attic gets damp no matter how much insulation is in it.

How much insulation should my attic have?

It is settled depth and even coverage that decide performance, not the product name. We set depth markers before blowing so the result is measurable, and check the corners rather than just the area near the hatch.

Attic Insulation Steinhauer Edmonton | Attic Top-Up

Blown-in attic insulation in Steinhauer, sealed before it is filled

Attics in Steinhauer lose depth over time — insulation settles, someone crawls through it for a wiring job, and the corners near the eaves are usually thin to begin with. A top-up is only worth doing if the baffles are clear and the ceiling below is sealed, so that is what we check before quoting.

Attic hatch insulated and weatherstripped
Existing insulation levelled before the top-up
Blown-in loose-fill to the depth your permit specifies
Baffles kept clear so the soffit vents still breathe
Depth markers left in place so the result is verifiable
Air sealing at pot lights, top plates and the attic hatch

Cellulose against fibreglass in an Steinhauer attic

Two products, different behaviour

Blown cellulose is denser, settles into gaps well and resists air movement through it better. Blown fibreglass is lighter, does not settle as much over time and is less prone to holding moisture.

How we choose

Either performs when installed to the right depth with the ceiling sealed underneath. We pick based on what is already up there and how the attic is built, and we tell you which we would use and why rather than defaulting to whichever is on the truck.

Steinhauer drywall in context

About Steinhauer

The neighbourhood is named for Henry Bird Steinhauer, a missionary who settled in Alberta during the mid-1800s (and from whom the family of the former Lieutenant Governor takes its name).

What we see in Steinhauer

In Steinhauer the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Sealing the ceiling below first

The order that matters

Warm moist air leaking from the house into a cold Steinhauer attic is what frosts the underside of the roof deck and wets the insulation.

Where it leaks

The hatch, pot lights, bath fans, plumbing stacks and the top plates of interior walls. Blowing more insulation over unsealed penetrations buries the problem instead of fixing it, so sealing comes first.

Adding to what is already there

You rarely start empty

Most Steinhauer attics already have something, whether old batts, older loose fill, or both in layers.

When to top up and when not

If the existing material is dry, even and uncontaminated, adding over it is usually the best value. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we say which one we found.

Depth is the whole number

What you are buying

Attic performance is almost entirely a function of settled depth and even coverage. Two attics with the same product can perform very differently.

How we handle it

Depth markers are set before blowing so the result is measurable rather than asserted, and the Steinhauer attic is checked at the corners rather than only where the hatch is. An attic that is deep in the middle and thin at the perimeter is the usual finding.

What we can and cannot tell you about savings

Honest about the number

We will not quote you a percentage off your heating bill. It depends on your current depth, your air leakage, your windows, your furnace and how you heat the house.

What we will say

What the attic has now, what it would have after, and where the leaks are. Those are things we can measure and show you. A savings figure from a contractor who has not seen your utility bills is a sales number, not an estimate.

Pot lights, and which ones can be covered

Not all fixtures are equal

Older recessed fixtures in Steinhauer ceilings need clearance and cannot be buried. Newer IC-rated fixtures are built to be in contact with insulation.

What we check

We identify what is installed before blowing. Where fixtures cannot be covered, they need boxing or replacing — and each one is also a significant air leak, so they are usually the first thing sealed regardless of type.

How it works

Simple, clean, on schedule — Attic Insulation in Steinhauer Edmonton

Free quote

We come out to your Steinhauer Edmonton property, take a real look at the attic insulation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every attic insulation quote in Steinhauer Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the attic insulation in Steinhauer Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Steinhauer Edmonton home while we finish the attic insulation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished attic insulation with us and you're happy with the result in Steinhauer Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the attic insulation contractor Steinhauer Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your attic insulation project in Steinhauer Edmonton.

Read our reviews on Google

FAQ — Attic Insulation Steinhauer Edmonton

Attic Insulation Steinhauer Edmonton: your questions answered

Do I need to seal before adding insulation?: Yes, and it is the part most often skipped. Warm moist air leaking from the house frosts the roof deck and wets the insulation. Blowing over unsealed pot lights and top plates buries the problem instead of fixing it.
Can I add over the old insulation?: Usually yes, if it is dry, even and uncontaminated. If it is wet, compacted, rodent-affected or hiding unsealed penetrations, removing it first is worth the cost, and we tell you which one we found.
I store things in my attic. Can I keep doing that?: Yes, but the plywood squashes the insulation beneath it to joist depth. Either the storage area gets raised on a platform above the finished depth, or it stays as a deliberately weaker zone kept small. We will not top up around it and pretend it is not there.
How do I know I got the depth I paid for?: We leave depth markers through the attic so the installed depth can be read off by anyone afterwards. Depth is easy to claim and hard to check once the hatch is closed, which is exactly why we mark it.
Will you block my soffit vents?: No. Baffles hold the insulation back at the eaves so air can still move from the soffits to the ridge. A blocked attic gets damp no matter how much insulation is in it.
How much insulation should my attic have?: It is settled depth and even coverage that decide performance, not the product name. We set depth markers before blowing so the result is measurable, and check the corners rather than just the area near the hatch.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Attic Insulation Steinhauer Edmonton

Blown-in attic insulation in Steinhauer, sealed before it is filled