Is it a problem to have poly on both sides?

Yes. Two barriers trap moisture between them with no direction to dry. It is a real mistake we still find in renovated Wedgewood Heights walls, and it stays invisible until the damage shows.

Does it matter where the sheets overlap?

Yes. A lap must land on solid framing and be sealed with acoustical sealant compressed between layers. An unsupported lap taped across a cavity flexes with pressure changes and works loose.

What about outlets on exterior walls?

Each one is a deliberate hole. They need poly hats or airtight boxes sealed to the sheet. Taping poly to the front of an ordinary box does not last once board is fastened over it, and it is the most common leak we find.

Is a bathroom done differently?

Same rules, larger consequences. A bathroom pushes far more vapour into the wall, so a gap shows up faster. The fan housing and duct are sealed rather than trimmed around, and we check the fan vents outside rather than into the attic.

Can you install the barrier if someone else did the insulation?

Yes, but we check the insulation first. A barrier over a poorly filled cavity locks the problem in, and once the board is on neither can be corrected without opening the wall.

Is a basement wall done the same way as an upstairs wall?

No. A basement wall can take moisture from the ground too, so poly detailed like an above-grade wall can trap moisture against the concrete. The insulation is held off the concrete so the wall can dry, with vapour control on the warm side.

Vapour Barrier Installation Wedgewood Heights Edmonton | 6 Mil Poly

Poly and air sealing in Wedgewood Heights before the board goes on

A vapour barrier only works as a continuous plane. In Wedgewood Heights the failures are almost never the sheet itself — they are the electrical boxes, the top and bottom plates, the window returns and the penetrations, where the poly is cut and not resealed.

Poly on the warm side of the insulation
Window and door returns detailed properly
Left ready for inspection before boarding
Rim joists air-sealed before insulating
Electrical boxes poly-hatted and sealed
Seams lapped at framing and sealed, not just taped

Renovations, and meeting an existing barrier

Continuity across old and new

In an Wedgewood Heights renovation the new poly has to tie into whatever is already in the wall. A new sheet stopped at the edge of the work leaves an open seam inside the assembly.

What we look for

Whether an existing barrier is present at all, what condition it is in, and whether there is a second one somewhere that would trap moisture between the two. Older renovations quite often have both, and finding that before boarding is worth the hour it takes.

Wedgewood Heights drywall in context

About Wedgewood Heights

Most of the roads in Wedgewood Heights are named in honour of well-known Edmontonians.

What we see in Wedgewood Heights

In Wedgewood Heights the drywall work is popcorn and stipple ceiling removal, settling+truss-uplift cracks, nail pops, Poly-B repipe patching repipe patching. We confirm what your home actually needs on site, in writing, before anything starts.

Warm side, always

The one rule everything else follows

The barrier goes on the heated side of the insulation. In an Wedgewood Heights climate that is the room side of an exterior wall.

Why position decides everything

Put it on the cold side and you have placed a moisture stop exactly where indoor humidity will condense against it, inside the wall, where nothing dries and nothing is visible until the damage is done.

Where poly is the wrong choice

Not every assembly wants it

Some Wedgewood Heights walls, such as an insulated concrete basement or an assembly with exterior rigid insulation, are designed to dry inward, and a full poly layer stops that.

How we approach it

We look at the whole assembly rather than defaulting to poly because it is what is usually done. Where a smart or variable-permeance membrane is the right call, we say so.

The parts an inspector looks at first

Predictable list

Electrical boxes, seams landing off framing, the top and bottom plates, window returns and any penetration. Those are where Wedgewood Heights vapour barrier inspections fail, and they fail for the same reasons every time.

Why we sequence to it

We leave the work visible and board after the inspection rather than ahead of it. Covering something an inspector needs to see costs a wall, not an afternoon.

Inspection, and leaving it visible

It gets checked before it is covered

Vapour barrier and air sealing in Wedgewood Heights are inspected before drywall covers them. We sequence to your inspection date rather than boarding ahead and covering something the inspector needs to see.

If it does not pass

We want the inspector's note directly. Most failures are specific — an unsealed box, a floating seam, a torn return — and they are corrected faster from the actual note than from a second-hand summary.

Electrical boxes, the usual failure point

A hole in the plane

Every outlet and switch in an Wedgewood Heights exterior wall is a cut in the poly. Left unsealed it is a direct path for moist air into the cavity, and the boxes are usually the coldest spot on the wall.

Poly hats and sealant

Boxes get a poly hat or an air-sealed box, and the poly is sealed to it rather than simply cut around. It is a small detail repeated dozens of times, which is exactly why it gets skipped.

How it works

Simple, clean, on schedule — Vapour Barrier Installation in Wedgewood Heights Edmonton

Free quote

We come out to your Wedgewood Heights Edmonton property, take a real look at the vapour barrier installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every vapour barrier installation quote in Wedgewood Heights Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the vapour barrier installation in Wedgewood Heights Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Wedgewood Heights Edmonton home while we finish the vapour barrier installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished vapour barrier installation with us and you're happy with the result in Wedgewood Heights Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the vapour barrier installation contractor Wedgewood Heights Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your vapour barrier installation project in Wedgewood Heights Edmonton.

Read our reviews on Google

FAQ — Vapour Barrier Installation Wedgewood Heights Edmonton

Vapour Barrier Installation Wedgewood Heights Edmonton: your questions answered

Is it a problem to have poly on both sides?: Yes. Two barriers trap moisture between them with no direction to dry. It is a real mistake we still find in renovated Wedgewood Heights walls, and it stays invisible until the damage shows.
Does it matter where the sheets overlap?: Yes. A lap must land on solid framing and be sealed with acoustical sealant compressed between layers. An unsupported lap taped across a cavity flexes with pressure changes and works loose.
What about outlets on exterior walls?: Each one is a deliberate hole. They need poly hats or airtight boxes sealed to the sheet. Taping poly to the front of an ordinary box does not last once board is fastened over it, and it is the most common leak we find.
Is a bathroom done differently?: Same rules, larger consequences. A bathroom pushes far more vapour into the wall, so a gap shows up faster. The fan housing and duct are sealed rather than trimmed around, and we check the fan vents outside rather than into the attic.
Can you install the barrier if someone else did the insulation?: Yes, but we check the insulation first. A barrier over a poorly filled cavity locks the problem in, and once the board is on neither can be corrected without opening the wall.
Is a basement wall done the same way as an upstairs wall?: No. A basement wall can take moisture from the ground too, so poly detailed like an above-grade wall can trap moisture against the concrete. The insulation is held off the concrete so the wall can dry, with vapour control on the warm side.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Vapour Barrier Installation Wedgewood Heights Edmonton

Poly and air sealing in Wedgewood Heights before the board goes on