Do the electrical boxes really need sealing?

They are the most common failure point. Every outlet in an exterior wall is a cut in the plane, and unsealed it is a direct path for moist air into the cavity at the coldest part of the wall.

Is a bathroom done differently?

Same rules, larger consequences. A bathroom pushes far more vapour into the wall, so a gap shows up faster. The fan housing and duct are sealed rather than trimmed around, and we check the fan vents outside rather than into the attic.

Is it a problem to have poly on both sides?

Yes. Two barriers trap moisture between them with no direction to dry. It is a real mistake we still find in renovated University of Alberta walls, and it stays invisible until the damage shows.

Which side does the vapour barrier go on?

The warm side of the insulation. Through an Alberta winter moisture pushes outward from the heated space, and the barrier stops it before it reaches a cold surface where it can condense.

Does it matter where the sheet meets the ceiling and floor?

It is the whole job. Left loose at the top or bottom plate, warm air simply goes over or under a perfectly installed sheet. The junction into a vaulted ceiling is the most commonly skipped and the wettest point in the room.

Does it matter where the sheets overlap?

Yes. A lap must land on solid framing and be sealed with acoustical sealant compressed between layers. An unsupported lap taped across a cavity flexes with pressure changes and works loose.

Vapour Barrier Installation University of Alberta Edmonton | 6 Mil Poly

Poly and air sealing in University of Alberta before the board goes on

A vapour barrier only works as a continuous plane. In University of Alberta the failures are almost never the sheet itself — they are the electrical boxes, the top and bottom plates, the window returns and the penetrations, where the poly is cut and not resealed.

Window and door returns detailed properly
Rim joists air-sealed before insulating
Seams lapped at framing and sealed, not just taped
Left ready for inspection before boarding
Electrical boxes poly-hatted and sealed
Poly on the warm side of the insulation

Where poly is the wrong choice

Not every assembly wants it

Some University of Alberta walls, such as an insulated concrete basement or an assembly with exterior rigid insulation, are designed to dry inward, and a full poly layer stops that.

How we approach it

We look at the whole assembly rather than defaulting to poly because it is what is usually done. Where a smart or variable-permeance membrane is the right call, we say so.

University of Alberta drywall in context

About University of Alberta

This multi-use neighbourhood is both residential and educational in nature.

What we see in University of Alberta

In University of Alberta the drywall work is first-year settling, basement dev for first owners, Level 5 over builder-grade. We confirm what your home actually needs on site, in writing, before anything starts.

Never two barriers

The trap

Poly on the room side plus a second impermeable layer behind the insulation leaves any moisture that gets in with no direction to dry.

Where it happens

Renovations, mostly. A new barrier gets added over a wall that already had a foil-faced or kraft-faced layer. We look at what is already in an University of Alberta wall before adding to it rather than assuming the cavity is bare.

Warm side, always

The one rule everything else follows

The barrier goes on the heated side of the insulation. In an University of Alberta climate that is the room side of an exterior wall.

Why position decides everything

Put it on the cold side and you have placed a moisture stop exactly where indoor humidity will condense against it, inside the wall, where nothing dries and nothing is visible until the damage is done.

Where the barrier meets the ceiling and the floor

The two continuous edges

A University of Alberta wall barrier has to be sealed at the top plate and the bottom plate. Left loose, warm air simply goes over or under a perfectly installed sheet.

Cathedral and vaulted areas

Where a wall runs into a vaulted ceiling the junction is awkward and often skipped. It is also the warmest, wettest point in the room because that is where the air collects. It gets detailed properly or the rest of the sheet is decorative.

Inspection, and leaving it visible

It gets checked before it is covered

Vapour barrier and air sealing in University of Alberta are inspected before drywall covers them. We sequence to your inspection date rather than boarding ahead and covering something the inspector needs to see.

If it does not pass

We want the inspector's note directly. Most failures are specific — an unsealed box, a floating seam, a torn return — and they are corrected faster from the actual note than from a second-hand summary.

Basement walls, where the rules change

Concrete complicates it

A University of Alberta basement wall can take moisture from the ground as well as from the room. That is why a poly barrier detailed the way it is on an above-grade wall can trap moisture against the concrete instead of keeping it out.

How the assembly is built

Rigid insulation or a framed cavity held off the concrete gives the wall a way to dry, with vapour control on the warm side of the insulation. Getting that order wrong is the most common reason a finished University of Alberta basement smells musty.

How it works

Simple, clean, on schedule — Vapour Barrier Installation in University Of Alberta Edmonton

Free quote

We come out to your University Of Alberta Edmonton property, take a real look at the vapour barrier installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every vapour barrier installation quote in University Of Alberta Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the vapour barrier installation in University Of Alberta Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your University Of Alberta Edmonton home while we finish the vapour barrier installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished vapour barrier installation with us and you're happy with the result in University Of Alberta Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the vapour barrier installation contractor University Of Alberta Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your vapour barrier installation project in University Of Alberta Edmonton.

Read our reviews on Google

FAQ — Vapour Barrier Installation University of Alberta Edmonton

Vapour Barrier Installation University of Alberta Edmonton: your questions answered

Do the electrical boxes really need sealing?: They are the most common failure point. Every outlet in an exterior wall is a cut in the plane, and unsealed it is a direct path for moist air into the cavity at the coldest part of the wall.
Is a bathroom done differently?: Same rules, larger consequences. A bathroom pushes far more vapour into the wall, so a gap shows up faster. The fan housing and duct are sealed rather than trimmed around, and we check the fan vents outside rather than into the attic.
Is it a problem to have poly on both sides?: Yes. Two barriers trap moisture between them with no direction to dry. It is a real mistake we still find in renovated University of Alberta walls, and it stays invisible until the damage shows.
Which side does the vapour barrier go on?: The warm side of the insulation. Through an Alberta winter moisture pushes outward from the heated space, and the barrier stops it before it reaches a cold surface where it can condense.
Does it matter where the sheet meets the ceiling and floor?: It is the whole job. Left loose at the top or bottom plate, warm air simply goes over or under a perfectly installed sheet. The junction into a vaulted ceiling is the most commonly skipped and the wettest point in the room.
Does it matter where the sheets overlap?: Yes. A lap must land on solid framing and be sealed with acoustical sealant compressed between layers. An unsupported lap taped across a cavity flexes with pressure changes and works loose.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Vapour Barrier Installation University of Alberta Edmonton

Poly and air sealing in University of Alberta before the board goes on