Is a bathroom done differently?

Same rules, larger consequences. A bathroom pushes far more vapour into the wall, so a gap shows up faster. The fan housing and duct are sealed rather than trimmed around, and we check the fan vents outside rather than into the attic.

Does it matter where the sheets overlap?

Yes. A lap must land on solid framing and be sealed with acoustical sealant compressed between layers. An unsupported lap taped across a cavity flexes with pressure changes and works loose.

Is the vapour barrier the same as an air barrier?

Not by itself. Poly slows vapour diffusion; sealed properly it also slows air, and unsealed it does very little of either. The sealing is what turns a sheet of plastic into a working assembly.

Which side does the vapour barrier go on?

The warm side of the insulation. Through an Alberta winter moisture pushes outward from the heated space, and the barrier stops it before it reaches a cold surface where it can condense.

What about outlets on exterior walls?

Each one is a deliberate hole. They need poly hats or airtight boxes sealed to the sheet. Taping poly to the front of an ordinary box does not last once board is fastened over it, and it is the most common leak we find.

Do the electrical boxes really need sealing?

They are the most common failure point. Every outlet in an exterior wall is a cut in the plane, and unsealed it is a direct path for moist air into the cavity at the coldest part of the wall.

Vapour Barrier Installation Strathearn Edmonton | 6 Mil Poly

Vapour barrier in Strathearn, sealed as a continuous plane

A vapour barrier only works as a continuous plane. In Strathearn the failures are almost never the sheet itself — they are the electrical boxes, the top and bottom plates, the window returns and the penetrations, where the poly is cut and not resealed.

Window and door returns detailed properly
Seams lapped at framing and sealed, not just taped
Poly on the warm side of the insulation
Rim joists air-sealed before insulating
Left ready for inspection before boarding
Electrical boxes poly-hatted and sealed

Why the warm side, and why only one

Which way the moisture moves

Through an Strathearn winter, warm humid indoor air pushes outward through the assembly. A vapour barrier on the warm side stops that moisture before it reaches a cold surface where it can condense.

Two barriers is worse than one

A second barrier on the cold side traps moisture between the two with no direction to dry. It is a genuine mistake we still find in renovated walls, and it is invisible until the damage shows.

Strathearn drywall in context

About Strathearn

McKernan, Edmonton's first telegraph operator, and W.

What we see in Strathearn

In Strathearn the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Windows, doors and the returns around them

Where the detail gets fiddly

The return between a window frame and the wall in Strathearn is awkward, tight, and often left as a torn edge tucked behind trim.

Why it matters

It is also a cold junction where condensation shows first, usually as staining or mould at the reveal. The poly is cut to fit, sealed to the frame and supported, rather than folded and hoped for.

Poly against smart membranes

Two approaches

Standard 6-mil poly is the common choice in Strathearn and works when it is continuous and sealed. A variable-permeance membrane tightens in winter and opens in summer, giving the assembly a drying path in both directions.

When it is worth the difference

Most straightforward walls are fine with poly. Retrofits, assemblies that cannot be fully sealed and some basement details benefit from a membrane. We say which we would use and why rather than defaulting.

Bathrooms, kitchens and the wet rooms

More moisture, same rules

A Strathearn bathroom pushes far more vapour into the wall than a bedroom. The barrier is not different, but the consequences of a gap are larger and show up faster.

Fans and penetrations

The fan housing, the duct and any pot lights all pierce the plane in the wettest room in the house. Those are sealed rather than trimmed around, and we check that the fan actually vents outside rather than into the attic.

Warm side, always

The one rule everything else follows

The barrier goes on the heated side of the insulation. In an Strathearn climate that is the room side of an exterior wall.

Why position decides everything

Put it on the cold side and you have placed a moisture stop exactly where indoor humidity will condense against it, inside the wall, where nothing dries and nothing is visible until the damage is done.

Top plates, bottom plates and the perimeter

The edges do the leaking

The continuous joints at the top and bottom of an Strathearn wall are longer than every box and lap put together, and they are the easiest to seal well or badly.

What good looks like

Sealant on the plate, poly laid into it and compressed by the framing or the board above, carried around corners rather than cut and butted at every change of direction.

How it works

Simple, clean, on schedule — Vapour Barrier Installation in Strathearn Edmonton

Free quote

We come out to your Strathearn Edmonton property, take a real look at the vapour barrier installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every vapour barrier installation quote in Strathearn Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the vapour barrier installation in Strathearn Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Strathearn Edmonton home while we finish the vapour barrier installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished vapour barrier installation with us and you're happy with the result in Strathearn Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the vapour barrier installation contractor Strathearn Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your vapour barrier installation project in Strathearn Edmonton.

Read our reviews on Google

FAQ — Vapour Barrier Installation Strathearn Edmonton

Vapour Barrier Installation Strathearn Edmonton: your questions answered

Is a bathroom done differently?: Same rules, larger consequences. A bathroom pushes far more vapour into the wall, so a gap shows up faster. The fan housing and duct are sealed rather than trimmed around, and we check the fan vents outside rather than into the attic.
Does it matter where the sheets overlap?: Yes. A lap must land on solid framing and be sealed with acoustical sealant compressed between layers. An unsupported lap taped across a cavity flexes with pressure changes and works loose.
Is the vapour barrier the same as an air barrier?: Not by itself. Poly slows vapour diffusion; sealed properly it also slows air, and unsealed it does very little of either. The sealing is what turns a sheet of plastic into a working assembly.
Which side does the vapour barrier go on?: The warm side of the insulation. Through an Alberta winter moisture pushes outward from the heated space, and the barrier stops it before it reaches a cold surface where it can condense.
What about outlets on exterior walls?: Each one is a deliberate hole. They need poly hats or airtight boxes sealed to the sheet. Taping poly to the front of an ordinary box does not last once board is fastened over it, and it is the most common leak we find.
Do the electrical boxes really need sealing?: They are the most common failure point. Every outlet in an exterior wall is a cut in the plane, and unsealed it is a direct path for moist air into the cavity at the coldest part of the wall.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Vapour Barrier Installation Strathearn Edmonton

Vapour barrier in Strathearn, sealed as a continuous plane