Is poly always the right answer?

No. Some assemblies, such as insulated concrete basements or walls with exterior rigid insulation, are designed to dry inward, and poly stops that. We look at the whole assembly rather than defaulting.

Can I add poly over insulation that already has a facing?

Usually no. Two retarders leave any moisture that gets in with no direction to dry. We check what is already in the wall before adding to it rather than assuming the cavity is bare.

Will this pass inspection?

It is built to what the code asks for on your permit, and we leave it visible and sequence to your inspection date rather than boarding ahead. If an inspector raises something, we want the note directly so it is fixed from the actual reason.

Will this stop water coming through my basement wall?

No, and installing it would hide the evidence. Water coming through a wall is a drainage and waterproofing problem. Vapour control manages moisture in the air, not liquid water, and we will say so rather than board over it.

Should I use poly or a smart membrane?

Most straightforward Ogilvie Ridge walls are fine with 6-mil poly, continuous and sealed. A variable-permeance membrane is worth it on retrofits and some basement details because it gives the assembly a drying path in both directions.

Does it matter where the sheets overlap?

Yes. A lap must land on solid framing and be sealed with acoustical sealant compressed between layers. An unsupported lap taped across a cavity flexes with pressure changes and works loose.

Vapour Barrier Installation Ogilvie Ridge Edmonton | 6 Mil Poly

Poly and air sealing in Ogilvie Ridge before the board goes on

Alberta winters put a large vapour drive from inside to outside, so the barrier belongs on the warm side of the insulation. Getting the position right matters as much as getting it sealed: a second barrier on the cold side traps moisture in the assembly with no way to dry.

Seams lapped at framing and sealed, not just taped
Window and door returns detailed properly
Rim joists air-sealed before insulating
Left ready for inspection before boarding
Electrical boxes poly-hatted and sealed
Poly on the warm side of the insulation

Never two barriers

The trap

Poly on the room side plus a second impermeable layer behind the insulation leaves any moisture that gets in with no direction to dry.

Where it happens

Renovations, mostly. A new barrier gets added over a wall that already had a foil-faced or kraft-faced layer. We look at what is already in an Ogilvie Ridge wall before adding to it rather than assuming the cavity is bare.

Windows, doors and the returns around them

Where the detail gets fiddly

The return between a window frame and the wall in Ogilvie Ridge is awkward, tight, and often left as a torn edge tucked behind trim.

Why it matters

It is also a cold junction where condensation shows first, usually as staining or mould at the reveal. The poly is cut to fit, sealed to the frame and supported, rather than folded and hoped for.

Inspecting it before it is covered

Last chance to see it

Once board is on, an Ogilvie Ridge vapour barrier is inaccessible for the life of the wall.

How we work

The barrier gets walked and repaired, every box, every lap, every penetration, before boarding is scheduled, and it is photographed. A tear found before the board goes on costs a piece of tape; found afterwards it costs a wall.

The parts an inspector looks at first

Predictable list

Electrical boxes, seams landing off framing, the top and bottom plates, window returns and any penetration. Those are where Ogilvie Ridge vapour barrier inspections fail, and they fail for the same reasons every time.

Why we sequence to it

We leave the work visible and board after the inspection rather than ahead of it. Covering something an inspector needs to see costs a wall, not an afternoon.

Renovations, and meeting an existing barrier

Continuity across old and new

In an Ogilvie Ridge renovation the new poly has to tie into whatever is already in the wall. A new sheet stopped at the edge of the work leaves an open seam inside the assembly.

What we look for

Whether an existing barrier is present at all, what condition it is in, and whether there is a second one somewhere that would trap moisture between the two. Older renovations quite often have both, and finding that before boarding is worth the hour it takes.

Bathrooms, kitchens and the wet rooms

More moisture, same rules

A Ogilvie Ridge bathroom pushes far more vapour into the wall than a bedroom. The barrier is not different, but the consequences of a gap are larger and show up faster.

Fans and penetrations

The fan housing, the duct and any pot lights all pierce the plane in the wettest room in the house. Those are sealed rather than trimmed around, and we check that the fan actually vents outside rather than into the attic.

How it works

Simple, clean, on schedule — Vapour Barrier Installation in Ogilvie Ridge Edmonton

Free quote

We come out to your Ogilvie Ridge Edmonton property, take a real look at the vapour barrier installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every vapour barrier installation quote in Ogilvie Ridge Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the vapour barrier installation in Ogilvie Ridge Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Ogilvie Ridge Edmonton home while we finish the vapour barrier installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished vapour barrier installation with us and you're happy with the result in Ogilvie Ridge Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the vapour barrier installation contractor Ogilvie Ridge Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your vapour barrier installation project in Ogilvie Ridge Edmonton.

Read our reviews on Google

FAQ — Vapour Barrier Installation Ogilvie Ridge Edmonton

Vapour Barrier Installation Ogilvie Ridge Edmonton: your questions answered

Is poly always the right answer?: No. Some assemblies, such as insulated concrete basements or walls with exterior rigid insulation, are designed to dry inward, and poly stops that. We look at the whole assembly rather than defaulting.
Can I add poly over insulation that already has a facing?: Usually no. Two retarders leave any moisture that gets in with no direction to dry. We check what is already in the wall before adding to it rather than assuming the cavity is bare.
Will this pass inspection?: It is built to what the code asks for on your permit, and we leave it visible and sequence to your inspection date rather than boarding ahead. If an inspector raises something, we want the note directly so it is fixed from the actual reason.
Will this stop water coming through my basement wall?: No, and installing it would hide the evidence. Water coming through a wall is a drainage and waterproofing problem. Vapour control manages moisture in the air, not liquid water, and we will say so rather than board over it.
Should I use poly or a smart membrane?: Most straightforward Ogilvie Ridge walls are fine with 6-mil poly, continuous and sealed. A variable-permeance membrane is worth it on retrofits and some basement details because it gives the assembly a drying path in both directions.
Does it matter where the sheets overlap?: Yes. A lap must land on solid framing and be sealed with acoustical sealant compressed between layers. An unsupported lap taped across a cavity flexes with pressure changes and works loose.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Vapour Barrier Installation Ogilvie Ridge Edmonton

Poly and air sealing in Ogilvie Ridge before the board goes on