Does it matter where the sheet meets the ceiling and floor?

It is the whole job. Left loose at the top or bottom plate, warm air simply goes over or under a perfectly installed sheet. The junction into a vaulted ceiling is the most commonly skipped and the wettest point in the room.

Which side does the vapour barrier go on?

The warm side of the insulation. Through an Alberta winter moisture pushes outward from the heated space, and the barrier stops it before it reaches a cold surface where it can condense.

Will this stop water coming through my basement wall?

No, and installing it would hide the evidence. Water coming through a wall is a drainage and waterproofing problem. Vapour control manages moisture in the air, not liquid water, and we will say so rather than board over it.

Why is there staining around my window reveals?

Usually the vapour barrier return at the window was torn or tucked rather than sealed. It is a cold junction, so condensation shows there first — often as staining or mould at the reveal.

Is a basement wall done the same way as an upstairs wall?

No. A basement wall can take moisture from the ground too, so poly detailed like an above-grade wall can trap moisture against the concrete. The insulation is held off the concrete so the wall can dry, with vapour control on the warm side.

Can you install the barrier if someone else did the insulation?

Yes, but we check the insulation first. A barrier over a poorly filled cavity locks the problem in, and once the board is on neither can be corrected without opening the wall.

Vapour Barrier Installation Lauderdale Edmonton | 6 Mil Poly

Poly and air sealing in Lauderdale before the board goes on

A vapour barrier only works as a continuous plane. In Lauderdale the failures are almost never the sheet itself — they are the electrical boxes, the top and bottom plates, the window returns and the penetrations, where the poly is cut and not resealed.

Rim joists air-sealed before insulating
Left ready for inspection before boarding
Seams lapped at framing and sealed, not just taped
Poly on the warm side of the insulation
Window and door returns detailed properly
Electrical boxes poly-hatted and sealed

Where the barrier meets the ceiling and the floor

The two continuous edges

A Lauderdale wall barrier has to be sealed at the top plate and the bottom plate. Left loose, warm air simply goes over or under a perfectly installed sheet.

Cathedral and vaulted areas

Where a wall runs into a vaulted ceiling the junction is awkward and often skipped. It is also the warmest, wettest point in the room because that is where the air collects. It gets detailed properly or the rest of the sheet is decorative.

Lauderdale drywall in context

About Lauderdale

James Lauder farmed and owned land near the neighbourhood before the turn of the 20th century.

What we see in Lauderdale

In Lauderdale the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Sealing at the electrical boxes

Every box is a hole

An outlet or switch on an exterior Lauderdale wall is a deliberate opening straight through the barrier.

The fix

Poly hats or airtight boxes, sealed to the sheet. Taping the poly to the front of an ordinary box does not last, because the board is fastened over it and the seal breaks. This is the single most common leak we find behind finished walls.

Why the warm side, and why only one

Which way the moisture moves

Through an Lauderdale winter, warm humid indoor air pushes outward through the assembly. A vapour barrier on the warm side stops that moisture before it reaches a cold surface where it can condense.

Two barriers is worse than one

A second barrier on the cold side traps moisture between the two with no direction to dry. It is a genuine mistake we still find in renovated walls, and it is invisible until the damage shows.

Poly against smart membranes

Two approaches

Standard 6-mil poly is the common choice in Lauderdale and works when it is continuous and sealed. A variable-permeance membrane tightens in winter and opens in summer, giving the assembly a drying path in both directions.

When it is worth the difference

Most straightforward walls are fine with poly. Retrofits, assemblies that cannot be fully sealed and some basement details benefit from a membrane. We say which we would use and why rather than defaulting.

Warm side, always

The one rule everything else follows

The barrier goes on the heated side of the insulation. In an Lauderdale climate that is the room side of an exterior wall.

Why position decides everything

Put it on the cold side and you have placed a moisture stop exactly where indoor humidity will condense against it, inside the wall, where nothing dries and nothing is visible until the damage is done.

Inspection, and leaving it visible

It gets checked before it is covered

Vapour barrier and air sealing in Lauderdale are inspected before drywall covers them. We sequence to your inspection date rather than boarding ahead and covering something the inspector needs to see.

If it does not pass

We want the inspector's note directly. Most failures are specific — an unsealed box, a floating seam, a torn return — and they are corrected faster from the actual note than from a second-hand summary.

How it works

Simple, clean, on schedule — Vapour Barrier Installation in Lauderdale Edmonton

Free quote

We come out to your Lauderdale Edmonton property, take a real look at the vapour barrier installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every vapour barrier installation quote in Lauderdale Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the vapour barrier installation in Lauderdale Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Lauderdale Edmonton home while we finish the vapour barrier installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished vapour barrier installation with us and you're happy with the result in Lauderdale Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the vapour barrier installation contractor Lauderdale Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your vapour barrier installation project in Lauderdale Edmonton.

Read our reviews on Google

FAQ — Vapour Barrier Installation Lauderdale Edmonton

Vapour Barrier Installation Lauderdale Edmonton: your questions answered

Does it matter where the sheet meets the ceiling and floor?: It is the whole job. Left loose at the top or bottom plate, warm air simply goes over or under a perfectly installed sheet. The junction into a vaulted ceiling is the most commonly skipped and the wettest point in the room.
Which side does the vapour barrier go on?: The warm side of the insulation. Through an Alberta winter moisture pushes outward from the heated space, and the barrier stops it before it reaches a cold surface where it can condense.
Will this stop water coming through my basement wall?: No, and installing it would hide the evidence. Water coming through a wall is a drainage and waterproofing problem. Vapour control manages moisture in the air, not liquid water, and we will say so rather than board over it.
Why is there staining around my window reveals?: Usually the vapour barrier return at the window was torn or tucked rather than sealed. It is a cold junction, so condensation shows there first — often as staining or mould at the reveal.
Is a basement wall done the same way as an upstairs wall?: No. A basement wall can take moisture from the ground too, so poly detailed like an above-grade wall can trap moisture against the concrete. The insulation is held off the concrete so the wall can dry, with vapour control on the warm side.
Can you install the barrier if someone else did the insulation?: Yes, but we check the insulation first. A barrier over a poorly filled cavity locks the problem in, and once the board is on neither can be corrected without opening the wall.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Vapour Barrier Installation Lauderdale Edmonton

Poly and air sealing in Lauderdale before the board goes on