Can I add poly over insulation that already has a facing?

Usually no. Two retarders leave any moisture that gets in with no direction to dry. We check what is already in the wall before adding to it rather than assuming the cavity is bare.

Will this stop water coming through my basement wall?

No, and installing it would hide the evidence. Water coming through a wall is a drainage and waterproofing problem. Vapour control manages moisture in the air, not liquid water, and we will say so rather than board over it.

Is a bathroom done differently?

Same rules, larger consequences. A bathroom pushes far more vapour into the wall, so a gap shows up faster. The fan housing and duct are sealed rather than trimmed around, and we check the fan vents outside rather than into the attic.

Is a basement wall done the same way as an upstairs wall?

No. A basement wall can take moisture from the ground too, so poly detailed like an above-grade wall can trap moisture against the concrete. The insulation is held off the concrete so the wall can dry, with vapour control on the warm side.

Does it matter where the sheet meets the ceiling and floor?

It is the whole job. Left loose at the top or bottom plate, warm air simply goes over or under a perfectly installed sheet. The junction into a vaulted ceiling is the most commonly skipped and the wettest point in the room.

Will this pass inspection?

It is built to what the code asks for on your permit, and we leave it visible and sequence to your inspection date rather than boarding ahead. If an inspector raises something, we want the note directly so it is fixed from the actual reason.

Vapour Barrier Installation Kenilworth Edmonton | 6 Mil Poly

Poly and air sealing in Kenilworth before the board goes on

A vapour barrier only works as a continuous plane. In Kenilworth the failures are almost never the sheet itself — they are the electrical boxes, the top and bottom plates, the window returns and the penetrations, where the poly is cut and not resealed.

Left ready for inspection before boarding
Window and door returns detailed properly
Electrical boxes poly-hatted and sealed
Rim joists air-sealed before insulating
Poly on the warm side of the insulation
Seams lapped at framing and sealed, not just taped

Basement walls, where the rules change

Concrete complicates it

A Kenilworth basement wall can take moisture from the ground as well as from the room. That is why a poly barrier detailed the way it is on an above-grade wall can trap moisture against the concrete instead of keeping it out.

How the assembly is built

Rigid insulation or a framed cavity held off the concrete gives the wall a way to dry, with vapour control on the warm side of the insulation. Getting that order wrong is the most common reason a finished Kenilworth basement smells musty.

Kenilworth drywall in context

About Kenilworth

Kenilworth lies in the City's southeast, immediately north of the vibrant Whyte Avenue.

What we see in Kenilworth

In Kenilworth the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Sealing at the electrical boxes

Every box is a hole

An outlet or switch on an exterior Kenilworth wall is a deliberate opening straight through the barrier.

The fix

Poly hats or airtight boxes, sealed to the sheet. Taping the poly to the front of an ordinary box does not last, because the board is fastened over it and the seal breaks. This is the single most common leak we find behind finished walls.

Where the barrier meets the ceiling and the floor

The two continuous edges

A Kenilworth wall barrier has to be sealed at the top plate and the bottom plate. Left loose, warm air simply goes over or under a perfectly installed sheet.

Cathedral and vaulted areas

Where a wall runs into a vaulted ceiling the junction is awkward and often skipped. It is also the warmest, wettest point in the room because that is where the air collects. It gets detailed properly or the rest of the sheet is decorative.

Renovations, and meeting an existing barrier

Continuity across old and new

In an Kenilworth renovation the new poly has to tie into whatever is already in the wall. A new sheet stopped at the edge of the work leaves an open seam inside the assembly.

What we look for

Whether an existing barrier is present at all, what condition it is in, and whether there is a second one somewhere that would trap moisture between the two. Older renovations quite often have both, and finding that before boarding is worth the hour it takes.

Warm side, always

The one rule everything else follows

The barrier goes on the heated side of the insulation. In an Kenilworth climate that is the room side of an exterior wall.

Why position decides everything

Put it on the cold side and you have placed a moisture stop exactly where indoor humidity will condense against it, inside the wall, where nothing dries and nothing is visible until the damage is done.

Laps, and the framing member behind them

Where sheets meet

A lap needs to land on solid framing and be sealed with acoustical sealant compressed between the layers, not taped in mid-air across a cavity.

Why it fails otherwise

An unsupported lap flexes with pressure changes and the seal works loose. In an Kenilworth build the sheets are planned so that laps fall on studs rather than wherever the roll ran out.

How it works

Simple, clean, on schedule — Vapour Barrier Installation in Kenilworth Edmonton

Free quote

We come out to your Kenilworth Edmonton property, take a real look at the vapour barrier installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every vapour barrier installation quote in Kenilworth Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the vapour barrier installation in Kenilworth Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Kenilworth Edmonton home while we finish the vapour barrier installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished vapour barrier installation with us and you're happy with the result in Kenilworth Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the vapour barrier installation contractor Kenilworth Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your vapour barrier installation project in Kenilworth Edmonton.

Read our reviews on Google

FAQ — Vapour Barrier Installation Kenilworth Edmonton

Vapour Barrier Installation Kenilworth Edmonton: your questions answered

Can I add poly over insulation that already has a facing?: Usually no. Two retarders leave any moisture that gets in with no direction to dry. We check what is already in the wall before adding to it rather than assuming the cavity is bare.
Will this stop water coming through my basement wall?: No, and installing it would hide the evidence. Water coming through a wall is a drainage and waterproofing problem. Vapour control manages moisture in the air, not liquid water, and we will say so rather than board over it.
Is a bathroom done differently?: Same rules, larger consequences. A bathroom pushes far more vapour into the wall, so a gap shows up faster. The fan housing and duct are sealed rather than trimmed around, and we check the fan vents outside rather than into the attic.
Is a basement wall done the same way as an upstairs wall?: No. A basement wall can take moisture from the ground too, so poly detailed like an above-grade wall can trap moisture against the concrete. The insulation is held off the concrete so the wall can dry, with vapour control on the warm side.
Does it matter where the sheet meets the ceiling and floor?: It is the whole job. Left loose at the top or bottom plate, warm air simply goes over or under a perfectly installed sheet. The junction into a vaulted ceiling is the most commonly skipped and the wettest point in the room.
Will this pass inspection?: It is built to what the code asks for on your permit, and we leave it visible and sequence to your inspection date rather than boarding ahead. If an inspector raises something, we want the note directly so it is fixed from the actual reason.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Vapour Barrier Installation Kenilworth Edmonton

Poly and air sealing in Kenilworth before the board goes on