Can I add poly over insulation that already has a facing?

Usually no. Two retarders leave any moisture that gets in with no direction to dry. We check what is already in the wall before adding to it rather than assuming the cavity is bare.

Will this stop water coming through my basement wall?

No, and installing it would hide the evidence. Water coming through a wall is a drainage and waterproofing problem. Vapour control manages moisture in the air, not liquid water, and we will say so rather than board over it.

Do the electrical boxes really need sealing?

They are the most common failure point. Every outlet in an exterior wall is a cut in the plane, and unsealed it is a direct path for moist air into the cavity at the coldest part of the wall.

Is the vapour barrier the same as an air barrier?

Not by itself. Poly slows vapour diffusion; sealed properly it also slows air, and unsealed it does very little of either. The sealing is what turns a sheet of plastic into a working assembly.

Is a basement wall done the same way as an upstairs wall?

No. A basement wall can take moisture from the ground too, so poly detailed like an above-grade wall can trap moisture against the concrete. The insulation is held off the concrete so the wall can dry, with vapour control on the warm side.

What about outlets on exterior walls?

Each one is a deliberate hole. They need poly hats or airtight boxes sealed to the sheet. Taping poly to the front of an ordinary box does not last once board is fastened over it, and it is the most common leak we find.

Vapour Barrier Installation Jamieson Place Edmonton | 6 Mil Poly

Poly and air sealing in Jamieson Place before the board goes on

Alberta winters put a large vapour drive from inside to outside, so the barrier belongs on the warm side of the insulation. Getting the position right matters as much as getting it sealed: a second barrier on the cold side traps moisture in the assembly with no way to dry.

Rim joists air-sealed before insulating
Poly on the warm side of the insulation
Window and door returns detailed properly
Left ready for inspection before boarding
Seams lapped at framing and sealed, not just taped
Electrical boxes poly-hatted and sealed

The parts an inspector looks at first

Predictable list

Electrical boxes, seams landing off framing, the top and bottom plates, window returns and any penetration. Those are where Jamieson Place vapour barrier inspections fail, and they fail for the same reasons every time.

Why we sequence to it

We leave the work visible and board after the inspection rather than ahead of it. Covering something an inspector needs to see costs a wall, not an afternoon.

Jamieson Place drywall in context

About Jamieson Place

Annexed in 1972 as part of West Jasper Place, this area is named for Colonel F.C.

What we see in Jamieson Place

In Jamieson Place the drywall work is popcorn and stipple ceiling removal, settling+truss-uplift cracks, nail pops, Poly-B repipe patching repipe patching. We confirm what your home actually needs on site, in writing, before anything starts.

Top plates, bottom plates and the perimeter

The edges do the leaking

The continuous joints at the top and bottom of an Jamieson Place wall are longer than every box and lap put together, and they are the easiest to seal well or badly.

What good looks like

Sealant on the plate, poly laid into it and compressed by the framing or the board above, carried around corners rather than cut and butted at every change of direction.

Bathrooms, kitchens and the wet rooms

More moisture, same rules

A Jamieson Place bathroom pushes far more vapour into the wall than a bedroom. The barrier is not different, but the consequences of a gap are larger and show up faster.

Fans and penetrations

The fan housing, the duct and any pot lights all pierce the plane in the wettest room in the house. Those are sealed rather than trimmed around, and we check that the fan actually vents outside rather than into the attic.

Poly against smart membranes

Two approaches

Standard 6-mil poly is the common choice in Jamieson Place and works when it is continuous and sealed. A variable-permeance membrane tightens in winter and opens in summer, giving the assembly a drying path in both directions.

When it is worth the difference

Most straightforward walls are fine with poly. Retrofits, assemblies that cannot be fully sealed and some basement details benefit from a membrane. We say which we would use and why rather than defaulting.

Laps, and the framing member behind them

Where sheets meet

A lap needs to land on solid framing and be sealed with acoustical sealant compressed between the layers, not taped in mid-air across a cavity.

Why it fails otherwise

An unsupported lap flexes with pressure changes and the seal works loose. In an Jamieson Place build the sheets are planned so that laps fall on studs rather than wherever the roll ran out.

Electrical boxes, the usual failure point

A hole in the plane

Every outlet and switch in an Jamieson Place exterior wall is a cut in the poly. Left unsealed it is a direct path for moist air into the cavity, and the boxes are usually the coldest spot on the wall.

Poly hats and sealant

Boxes get a poly hat or an air-sealed box, and the poly is sealed to it rather than simply cut around. It is a small detail repeated dozens of times, which is exactly why it gets skipped.

How it works

Simple, clean, on schedule — Vapour Barrier Installation in Jamieson Place Edmonton

Free quote

We come out to your Jamieson Place Edmonton property, take a real look at the vapour barrier installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every vapour barrier installation quote in Jamieson Place Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the vapour barrier installation in Jamieson Place Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Jamieson Place Edmonton home while we finish the vapour barrier installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished vapour barrier installation with us and you're happy with the result in Jamieson Place Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the vapour barrier installation contractor Jamieson Place Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your vapour barrier installation project in Jamieson Place Edmonton.

Read our reviews on Google

FAQ — Vapour Barrier Installation Jamieson Place Edmonton

Vapour Barrier Installation Jamieson Place Edmonton: your questions answered

Can I add poly over insulation that already has a facing?: Usually no. Two retarders leave any moisture that gets in with no direction to dry. We check what is already in the wall before adding to it rather than assuming the cavity is bare.
Will this stop water coming through my basement wall?: No, and installing it would hide the evidence. Water coming through a wall is a drainage and waterproofing problem. Vapour control manages moisture in the air, not liquid water, and we will say so rather than board over it.
Do the electrical boxes really need sealing?: They are the most common failure point. Every outlet in an exterior wall is a cut in the plane, and unsealed it is a direct path for moist air into the cavity at the coldest part of the wall.
Is the vapour barrier the same as an air barrier?: Not by itself. Poly slows vapour diffusion; sealed properly it also slows air, and unsealed it does very little of either. The sealing is what turns a sheet of plastic into a working assembly.
Is a basement wall done the same way as an upstairs wall?: No. A basement wall can take moisture from the ground too, so poly detailed like an above-grade wall can trap moisture against the concrete. The insulation is held off the concrete so the wall can dry, with vapour control on the warm side.
What about outlets on exterior walls?: Each one is a deliberate hole. They need poly hats or airtight boxes sealed to the sheet. Taping poly to the front of an ordinary box does not last once board is fastened over it, and it is the most common leak we find.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Vapour Barrier Installation Jamieson Place Edmonton

Poly and air sealing in Jamieson Place before the board goes on