Will this pass inspection?

It is built to what the code asks for on your permit, and we leave it visible and sequence to your inspection date rather than boarding ahead. If an inspector raises something, we want the note directly so it is fixed from the actual reason.

Do the electrical boxes really need sealing?

They are the most common failure point. Every outlet in an exterior wall is a cut in the plane, and unsealed it is a direct path for moist air into the cavity at the coldest part of the wall.

Will this stop water coming through my basement wall?

No, and installing it would hide the evidence. Water coming through a wall is a drainage and waterproofing problem. Vapour control manages moisture in the air, not liquid water, and we will say so rather than board over it.

Which side does the vapour barrier go on?

The warm side of the insulation. Through an Alberta winter moisture pushes outward from the heated space, and the barrier stops it before it reaches a cold surface where it can condense.

Why is there staining around my window reveals?

Usually the vapour barrier return at the window was torn or tucked rather than sealed. It is a cold junction, so condensation shows there first — often as staining or mould at the reveal.

Is a bathroom done differently?

Same rules, larger consequences. A bathroom pushes far more vapour into the wall, so a gap shows up faster. The fan housing and duct are sealed rather than trimmed around, and we check the fan vents outside rather than into the attic.

Vapour Barrier Installation Glengarry Edmonton | 6 Mil Poly

Vapour barrier details in Glengarry that pass inspection

Alberta winters put a large vapour drive from inside to outside, so the barrier belongs on the warm side of the insulation. Getting the position right matters as much as getting it sealed: a second barrier on the cold side traps moisture in the assembly with no way to dry.

Electrical boxes poly-hatted and sealed
Seams lapped at framing and sealed, not just taped
Left ready for inspection before boarding
Rim joists air-sealed before insulating
Window and door returns detailed properly
Poly on the warm side of the insulation

Why the warm side, and why only one

Which way the moisture moves

Through an Glengarry winter, warm humid indoor air pushes outward through the assembly. A vapour barrier on the warm side stops that moisture before it reaches a cold surface where it can condense.

Two barriers is worse than one

A second barrier on the cold side traps moisture between the two with no direction to dry. It is a genuine mistake we still find in renovated walls, and it is invisible until the damage shows.

Glengarry drywall in context

About Glengarry

Glengarry is a diverse mix of commercial, residential, institutional and recreational land uses.

What we see in Glengarry

In Glengarry the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

What a vapour barrier is not

It is not an air barrier by itself

Poly slows vapour diffusion. Sealed properly it also slows air, and unsealed it does very little of either. The sealing is what turns a sheet of plastic into a working assembly.

It is not a damp-proofing fix

If a Glengarry basement has water coming through the wall, vapour control is not the answer and installing it will hide the evidence. That is a drainage and waterproofing problem, and we will say so rather than board over it.

Renovations, and meeting an existing barrier

Continuity across old and new

In an Glengarry renovation the new poly has to tie into whatever is already in the wall. A new sheet stopped at the edge of the work leaves an open seam inside the assembly.

What we look for

Whether an existing barrier is present at all, what condition it is in, and whether there is a second one somewhere that would trap moisture between the two. Older renovations quite often have both, and finding that before boarding is worth the hour it takes.

Laps, and the framing member behind them

Where sheets meet

A lap needs to land on solid framing and be sealed with acoustical sealant compressed between the layers, not taped in mid-air across a cavity.

Why it fails otherwise

An unsupported lap flexes with pressure changes and the seal works loose. In an Glengarry build the sheets are planned so that laps fall on studs rather than wherever the roll ran out.

Basement walls, where the rules change

Concrete complicates it

A Glengarry basement wall can take moisture from the ground as well as from the room. That is why a poly barrier detailed the way it is on an above-grade wall can trap moisture against the concrete instead of keeping it out.

How the assembly is built

Rigid insulation or a framed cavity held off the concrete gives the wall a way to dry, with vapour control on the warm side of the insulation. Getting that order wrong is the most common reason a finished Glengarry basement smells musty.

Top plates, bottom plates and the perimeter

The edges do the leaking

The continuous joints at the top and bottom of an Glengarry wall are longer than every box and lap put together, and they are the easiest to seal well or badly.

What good looks like

Sealant on the plate, poly laid into it and compressed by the framing or the board above, carried around corners rather than cut and butted at every change of direction.

How it works

Simple, clean, on schedule — Vapour Barrier Installation in Glengarry Edmonton

Free quote

We come out to your Glengarry Edmonton property, take a real look at the vapour barrier installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every vapour barrier installation quote in Glengarry Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the vapour barrier installation in Glengarry Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Glengarry Edmonton home while we finish the vapour barrier installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished vapour barrier installation with us and you're happy with the result in Glengarry Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the vapour barrier installation contractor Glengarry Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your vapour barrier installation project in Glengarry Edmonton.

Read our reviews on Google

FAQ — Vapour Barrier Installation Glengarry Edmonton

Vapour Barrier Installation Glengarry Edmonton: your questions answered

Will this pass inspection?: It is built to what the code asks for on your permit, and we leave it visible and sequence to your inspection date rather than boarding ahead. If an inspector raises something, we want the note directly so it is fixed from the actual reason.
Do the electrical boxes really need sealing?: They are the most common failure point. Every outlet in an exterior wall is a cut in the plane, and unsealed it is a direct path for moist air into the cavity at the coldest part of the wall.
Will this stop water coming through my basement wall?: No, and installing it would hide the evidence. Water coming through a wall is a drainage and waterproofing problem. Vapour control manages moisture in the air, not liquid water, and we will say so rather than board over it.
Which side does the vapour barrier go on?: The warm side of the insulation. Through an Alberta winter moisture pushes outward from the heated space, and the barrier stops it before it reaches a cold surface where it can condense.
Why is there staining around my window reveals?: Usually the vapour barrier return at the window was torn or tucked rather than sealed. It is a cold junction, so condensation shows there first — often as staining or mould at the reveal.
Is a bathroom done differently?: Same rules, larger consequences. A bathroom pushes far more vapour into the wall, so a gap shows up faster. The fan housing and duct are sealed rather than trimmed around, and we check the fan vents outside rather than into the attic.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Vapour Barrier Installation Glengarry Edmonton

Vapour barrier details in Glengarry that pass inspection