Is poly always the right answer?

No. Some assemblies, such as insulated concrete basements or walls with exterior rigid insulation, are designed to dry inward, and poly stops that. We look at the whole assembly rather than defaulting.

Will this pass inspection?

It is built to what the code asks for on your permit, and we leave it visible and sequence to your inspection date rather than boarding ahead. If an inspector raises something, we want the note directly so it is fixed from the actual reason.

What if there is already a vapour barrier in the wall?

We tie into it, and we check whether there is a second one somewhere that would trap moisture between the two. Older Fulton Place renovations quite often have both, and finding that before boarding is worth the hour.

Does it matter where the sheets overlap?

Yes. A lap must land on solid framing and be sealed with acoustical sealant compressed between layers. An unsupported lap taped across a cavity flexes with pressure changes and works loose.

Is it a problem to have poly on both sides?

Yes. Two barriers trap moisture between them with no direction to dry. It is a real mistake we still find in renovated Fulton Place walls, and it stays invisible until the damage shows.

Is a basement wall done the same way as an upstairs wall?

No. A basement wall can take moisture from the ground too, so poly detailed like an above-grade wall can trap moisture against the concrete. The insulation is held off the concrete so the wall can dry, with vapour control on the warm side.

Vapour Barrier Installation Fulton Place Edmonton | 6 Mil Poly

Vapour barrier details in Fulton Place that pass inspection

A vapour barrier only works as a continuous plane. In Fulton Place the failures are almost never the sheet itself — they are the electrical boxes, the top and bottom plates, the window returns and the penetrations, where the poly is cut and not resealed.

Electrical boxes poly-hatted and sealed
Window and door returns detailed properly
Left ready for inspection before boarding
Poly on the warm side of the insulation
Rim joists air-sealed before insulating
Seams lapped at framing and sealed, not just taped

Seams belong on framing

Not floating in a bay

A lap sealed in the middle of a cavity has nothing solid behind it. Any movement or pressure opens it, and it cannot be inspected properly.

How we run it

Sheets are sized so seams land on a stud or plate, lapped, and sealed against solid backing. It uses slightly more material and it is the difference between a barrier that holds and one that is only continuous on the day it was installed.

Fulton Place drywall in context

About Fulton Place

Named for the creek which runs through the ravine on its west boundary, Fulton Place lies east of the downtown core and developed in the 1950s.

What we see in Fulton Place

In Fulton Place the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Never two barriers

The trap

Poly on the room side plus a second impermeable layer behind the insulation leaves any moisture that gets in with no direction to dry.

Where it happens

Renovations, mostly. A new barrier gets added over a wall that already had a foil-faced or kraft-faced layer. We look at what is already in an Fulton Place wall before adding to it rather than assuming the cavity is bare.

Why the warm side, and why only one

Which way the moisture moves

Through an Fulton Place winter, warm humid indoor air pushes outward through the assembly. A vapour barrier on the warm side stops that moisture before it reaches a cold surface where it can condense.

Two barriers is worse than one

A second barrier on the cold side traps moisture between the two with no direction to dry. It is a genuine mistake we still find in renovated walls, and it is invisible until the damage shows.

Top plates, bottom plates and the perimeter

The edges do the leaking

The continuous joints at the top and bottom of an Fulton Place wall are longer than every box and lap put together, and they are the easiest to seal well or badly.

What good looks like

Sealant on the plate, poly laid into it and compressed by the framing or the board above, carried around corners rather than cut and butted at every change of direction.

Basement walls, where the rules change

Concrete complicates it

A Fulton Place basement wall can take moisture from the ground as well as from the room. That is why a poly barrier detailed the way it is on an above-grade wall can trap moisture against the concrete instead of keeping it out.

How the assembly is built

Rigid insulation or a framed cavity held off the concrete gives the wall a way to dry, with vapour control on the warm side of the insulation. Getting that order wrong is the most common reason a finished Fulton Place basement smells musty.

Where the barrier meets the ceiling and the floor

The two continuous edges

A Fulton Place wall barrier has to be sealed at the top plate and the bottom plate. Left loose, warm air simply goes over or under a perfectly installed sheet.

Cathedral and vaulted areas

Where a wall runs into a vaulted ceiling the junction is awkward and often skipped. It is also the warmest, wettest point in the room because that is where the air collects. It gets detailed properly or the rest of the sheet is decorative.

How it works

Simple, clean, on schedule — Vapour Barrier Installation in Fulton Place Edmonton

Free quote

We come out to your Fulton Place Edmonton property, take a real look at the vapour barrier installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every vapour barrier installation quote in Fulton Place Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the vapour barrier installation in Fulton Place Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Fulton Place Edmonton home while we finish the vapour barrier installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished vapour barrier installation with us and you're happy with the result in Fulton Place Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the vapour barrier installation contractor Fulton Place Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your vapour barrier installation project in Fulton Place Edmonton.

Read our reviews on Google

FAQ — Vapour Barrier Installation Fulton Place Edmonton

Vapour Barrier Installation Fulton Place Edmonton: your questions answered

Is poly always the right answer?: No. Some assemblies, such as insulated concrete basements or walls with exterior rigid insulation, are designed to dry inward, and poly stops that. We look at the whole assembly rather than defaulting.
Will this pass inspection?: It is built to what the code asks for on your permit, and we leave it visible and sequence to your inspection date rather than boarding ahead. If an inspector raises something, we want the note directly so it is fixed from the actual reason.
What if there is already a vapour barrier in the wall?: We tie into it, and we check whether there is a second one somewhere that would trap moisture between the two. Older Fulton Place renovations quite often have both, and finding that before boarding is worth the hour.
Does it matter where the sheets overlap?: Yes. A lap must land on solid framing and be sealed with acoustical sealant compressed between layers. An unsupported lap taped across a cavity flexes with pressure changes and works loose.
Is it a problem to have poly on both sides?: Yes. Two barriers trap moisture between them with no direction to dry. It is a real mistake we still find in renovated Fulton Place walls, and it stays invisible until the damage shows.
Is a basement wall done the same way as an upstairs wall?: No. A basement wall can take moisture from the ground too, so poly detailed like an above-grade wall can trap moisture against the concrete. The insulation is held off the concrete so the wall can dry, with vapour control on the warm side.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Vapour Barrier Installation Fulton Place Edmonton

Vapour barrier details in Fulton Place that pass inspection