Is the vapour barrier the same as an air barrier?

Not by itself. Poly slows vapour diffusion; sealed properly it also slows air, and unsealed it does very little of either. The sealing is what turns a sheet of plastic into a working assembly.

Is a basement wall done the same way as an upstairs wall?

No. A basement wall can take moisture from the ground too, so poly detailed like an above-grade wall can trap moisture against the concrete. The insulation is held off the concrete so the wall can dry, with vapour control on the warm side.

Does it matter where the sheet meets the ceiling and floor?

It is the whole job. Left loose at the top or bottom plate, warm air simply goes over or under a perfectly installed sheet. The junction into a vaulted ceiling is the most commonly skipped and the wettest point in the room.

Does it matter where the sheets overlap?

Yes. A lap must land on solid framing and be sealed with acoustical sealant compressed between layers. An unsupported lap taped across a cavity flexes with pressure changes and works loose.

Is a bathroom done differently?

Same rules, larger consequences. A bathroom pushes far more vapour into the wall, so a gap shows up faster. The fan housing and duct are sealed rather than trimmed around, and we check the fan vents outside rather than into the attic.

Is it a problem to have poly on both sides?

Yes. Two barriers trap moisture between them with no direction to dry. It is a real mistake we still find in renovated Falconer Heights walls, and it stays invisible until the damage shows.

Vapour Barrier Installation Falconer Heights Edmonton | 6 Mil Poly

Vapour barrier in Falconer Heights, sealed as a continuous plane

Alberta winters put a large vapour drive from inside to outside, so the barrier belongs on the warm side of the insulation. Getting the position right matters as much as getting it sealed: a second barrier on the cold side traps moisture in the assembly with no way to dry.

Window and door returns detailed properly
Poly on the warm side of the insulation
Seams lapped at framing and sealed, not just taped
Electrical boxes poly-hatted and sealed
Left ready for inspection before boarding
Rim joists air-sealed before insulating

Inspection, and leaving it visible

It gets checked before it is covered

Vapour barrier and air sealing in Falconer Heights are inspected before drywall covers them. We sequence to your inspection date rather than boarding ahead and covering something the inspector needs to see.

If it does not pass

We want the inspector's note directly. Most failures are specific — an unsealed box, a floating seam, a torn return — and they are corrected faster from the actual note than from a second-hand summary.

Falconer Heights drywall in context

About Falconer Heights

Falconer, who was involved in the formation of Edmonton's Names Advisory Committee in the mid 1950s and served on the committee until 1979.

What we see in Falconer Heights

In Falconer Heights the drywall work is popcorn and stipple ceiling removal, settling+truss-uplift cracks, nail pops, Poly-B repipe patching repipe patching. We confirm what your home actually needs on site, in writing, before anything starts.

Never two barriers

The trap

Poly on the room side plus a second impermeable layer behind the insulation leaves any moisture that gets in with no direction to dry.

Where it happens

Renovations, mostly. A new barrier gets added over a wall that already had a foil-faced or kraft-faced layer. We look at what is already in an Falconer Heights wall before adding to it rather than assuming the cavity is bare.

The parts an inspector looks at first

Predictable list

Electrical boxes, seams landing off framing, the top and bottom plates, window returns and any penetration. Those are where Falconer Heights vapour barrier inspections fail, and they fail for the same reasons every time.

Why we sequence to it

We leave the work visible and board after the inspection rather than ahead of it. Covering something an inspector needs to see costs a wall, not an afternoon.

Why the warm side, and why only one

Which way the moisture moves

Through an Falconer Heights winter, warm humid indoor air pushes outward through the assembly. A vapour barrier on the warm side stops that moisture before it reaches a cold surface where it can condense.

Two barriers is worse than one

A second barrier on the cold side traps moisture between the two with no direction to dry. It is a genuine mistake we still find in renovated walls, and it is invisible until the damage shows.

Seams belong on framing

Not floating in a bay

A lap sealed in the middle of a cavity has nothing solid behind it. Any movement or pressure opens it, and it cannot be inspected properly.

How we run it

Sheets are sized so seams land on a stud or plate, lapped, and sealed against solid backing. It uses slightly more material and it is the difference between a barrier that holds and one that is only continuous on the day it was installed.

Laps, and the framing member behind them

Where sheets meet

A lap needs to land on solid framing and be sealed with acoustical sealant compressed between the layers, not taped in mid-air across a cavity.

Why it fails otherwise

An unsupported lap flexes with pressure changes and the seal works loose. In an Falconer Heights build the sheets are planned so that laps fall on studs rather than wherever the roll ran out.

How it works

Simple, clean, on schedule — Vapour Barrier Installation in Falconer Heights Edmonton

Free quote

We come out to your Falconer Heights Edmonton property, take a real look at the vapour barrier installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every vapour barrier installation quote in Falconer Heights Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the vapour barrier installation in Falconer Heights Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Falconer Heights Edmonton home while we finish the vapour barrier installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished vapour barrier installation with us and you're happy with the result in Falconer Heights Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the vapour barrier installation contractor Falconer Heights Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your vapour barrier installation project in Falconer Heights Edmonton.

Read our reviews on Google

FAQ — Vapour Barrier Installation Falconer Heights Edmonton

Vapour Barrier Installation Falconer Heights Edmonton: your questions answered

Is the vapour barrier the same as an air barrier?: Not by itself. Poly slows vapour diffusion; sealed properly it also slows air, and unsealed it does very little of either. The sealing is what turns a sheet of plastic into a working assembly.
Is a basement wall done the same way as an upstairs wall?: No. A basement wall can take moisture from the ground too, so poly detailed like an above-grade wall can trap moisture against the concrete. The insulation is held off the concrete so the wall can dry, with vapour control on the warm side.
Does it matter where the sheet meets the ceiling and floor?: It is the whole job. Left loose at the top or bottom plate, warm air simply goes over or under a perfectly installed sheet. The junction into a vaulted ceiling is the most commonly skipped and the wettest point in the room.
Does it matter where the sheets overlap?: Yes. A lap must land on solid framing and be sealed with acoustical sealant compressed between layers. An unsupported lap taped across a cavity flexes with pressure changes and works loose.
Is a bathroom done differently?: Same rules, larger consequences. A bathroom pushes far more vapour into the wall, so a gap shows up faster. The fan housing and duct are sealed rather than trimmed around, and we check the fan vents outside rather than into the attic.
Is it a problem to have poly on both sides?: Yes. Two barriers trap moisture between them with no direction to dry. It is a real mistake we still find in renovated Falconer Heights walls, and it stays invisible until the damage shows.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Vapour Barrier Installation Falconer Heights Edmonton

Vapour barrier in Falconer Heights, sealed as a continuous plane