Is the vapour barrier the same as an air barrier?

Not by itself. Poly slows vapour diffusion; sealed properly it also slows air, and unsealed it does very little of either. The sealing is what turns a sheet of plastic into a working assembly.

Is a bathroom done differently?

Same rules, larger consequences. A bathroom pushes far more vapour into the wall, so a gap shows up faster. The fan housing and duct are sealed rather than trimmed around, and we check the fan vents outside rather than into the attic.

Do the electrical boxes really need sealing?

They are the most common failure point. Every outlet in an exterior wall is a cut in the plane, and unsealed it is a direct path for moist air into the cavity at the coldest part of the wall.

Is it a problem to have poly on both sides?

Yes. Two barriers trap moisture between them with no direction to dry. It is a real mistake we still find in renovated Delton walls, and it stays invisible until the damage shows.

What if there is already a vapour barrier in the wall?

We tie into it, and we check whether there is a second one somewhere that would trap moisture between the two. Older Delton renovations quite often have both, and finding that before boarding is worth the hour.

Why is there staining around my window reveals?

Usually the vapour barrier return at the window was torn or tucked rather than sealed. It is a cold junction, so condensation shows there first — often as staining or mould at the reveal.

Vapour Barrier Installation Delton Edmonton | 6 Mil Poly

Vapour barrier details in Delton that pass inspection

A vapour barrier only works as a continuous plane. In Delton the failures are almost never the sheet itself — they are the electrical boxes, the top and bottom plates, the window returns and the penetrations, where the poly is cut and not resealed.

Window and door returns detailed properly
Seams lapped at framing and sealed, not just taped
Electrical boxes poly-hatted and sealed
Rim joists air-sealed before insulating
Poly on the warm side of the insulation
Left ready for inspection before boarding

Where the barrier meets the ceiling and the floor

The two continuous edges

A Delton wall barrier has to be sealed at the top plate and the bottom plate. Left loose, warm air simply goes over or under a perfectly installed sheet.

Cathedral and vaulted areas

Where a wall runs into a vaulted ceiling the junction is awkward and often skipped. It is also the warmest, wettest point in the room because that is where the air collects. It gets detailed properly or the rest of the sheet is decorative.

Delton drywall in context

About Delton

Delton has been part of Edmonton since 1910, a time when land speculators fuelled a tremendous expansion in the supply of vacant subdivisions.

What we see in Delton

In Delton the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Never two barriers

The trap

Poly on the room side plus a second impermeable layer behind the insulation leaves any moisture that gets in with no direction to dry.

Where it happens

Renovations, mostly. A new barrier gets added over a wall that already had a foil-faced or kraft-faced layer. We look at what is already in an Delton wall before adding to it rather than assuming the cavity is bare.

Inspection, and leaving it visible

It gets checked before it is covered

Vapour barrier and air sealing in Delton are inspected before drywall covers them. We sequence to your inspection date rather than boarding ahead and covering something the inspector needs to see.

If it does not pass

We want the inspector's note directly. Most failures are specific — an unsealed box, a floating seam, a torn return — and they are corrected faster from the actual note than from a second-hand summary.

Electrical boxes, the usual failure point

A hole in the plane

Every outlet and switch in an Delton exterior wall is a cut in the poly. Left unsealed it is a direct path for moist air into the cavity, and the boxes are usually the coldest spot on the wall.

Poly hats and sealant

Boxes get a poly hat or an air-sealed box, and the poly is sealed to it rather than simply cut around. It is a small detail repeated dozens of times, which is exactly why it gets skipped.

The parts an inspector looks at first

Predictable list

Electrical boxes, seams landing off framing, the top and bottom plates, window returns and any penetration. Those are where Delton vapour barrier inspections fail, and they fail for the same reasons every time.

Why we sequence to it

We leave the work visible and board after the inspection rather than ahead of it. Covering something an inspector needs to see costs a wall, not an afternoon.

Bathrooms, kitchens and the wet rooms

More moisture, same rules

A Delton bathroom pushes far more vapour into the wall than a bedroom. The barrier is not different, but the consequences of a gap are larger and show up faster.

Fans and penetrations

The fan housing, the duct and any pot lights all pierce the plane in the wettest room in the house. Those are sealed rather than trimmed around, and we check that the fan actually vents outside rather than into the attic.

How it works

Simple, clean, on schedule — Vapour Barrier Installation in Delton Edmonton

Free quote

We come out to your Delton Edmonton property, take a real look at the vapour barrier installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every vapour barrier installation quote in Delton Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the vapour barrier installation in Delton Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Delton Edmonton home while we finish the vapour barrier installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished vapour barrier installation with us and you're happy with the result in Delton Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the vapour barrier installation contractor Delton Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your vapour barrier installation project in Delton Edmonton.

Read our reviews on Google

FAQ — Vapour Barrier Installation Delton Edmonton

Vapour Barrier Installation Delton Edmonton: your questions answered

Is the vapour barrier the same as an air barrier?: Not by itself. Poly slows vapour diffusion; sealed properly it also slows air, and unsealed it does very little of either. The sealing is what turns a sheet of plastic into a working assembly.
Is a bathroom done differently?: Same rules, larger consequences. A bathroom pushes far more vapour into the wall, so a gap shows up faster. The fan housing and duct are sealed rather than trimmed around, and we check the fan vents outside rather than into the attic.
Do the electrical boxes really need sealing?: They are the most common failure point. Every outlet in an exterior wall is a cut in the plane, and unsealed it is a direct path for moist air into the cavity at the coldest part of the wall.
Is it a problem to have poly on both sides?: Yes. Two barriers trap moisture between them with no direction to dry. It is a real mistake we still find in renovated Delton walls, and it stays invisible until the damage shows.
What if there is already a vapour barrier in the wall?: We tie into it, and we check whether there is a second one somewhere that would trap moisture between the two. Older Delton renovations quite often have both, and finding that before boarding is worth the hour.
Why is there staining around my window reveals?: Usually the vapour barrier return at the window was torn or tucked rather than sealed. It is a cold junction, so condensation shows there first — often as staining or mould at the reveal.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Vapour Barrier Installation Delton Edmonton

Vapour barrier details in Delton that pass inspection