Can you install the barrier if someone else did the insulation?

Yes, but we check the insulation first. A barrier over a poorly filled cavity locks the problem in, and once the board is on neither can be corrected without opening the wall.

Why is there staining around my window reveals?

Usually the vapour barrier return at the window was torn or tucked rather than sealed. It is a cold junction, so condensation shows there first — often as staining or mould at the reveal.

Which side does the vapour barrier go on?

The warm side of the insulation. Through an Alberta winter moisture pushes outward from the heated space, and the barrier stops it before it reaches a cold surface where it can condense.

Do the electrical boxes really need sealing?

They are the most common failure point. Every outlet in an exterior wall is a cut in the plane, and unsealed it is a direct path for moist air into the cavity at the coldest part of the wall.

What about outlets on exterior walls?

Each one is a deliberate hole. They need poly hats or airtight boxes sealed to the sheet. Taping poly to the front of an ordinary box does not last once board is fastened over it, and it is the most common leak we find.

Is a basement wall done the same way as an upstairs wall?

No. A basement wall can take moisture from the ground too, so poly detailed like an above-grade wall can trap moisture against the concrete. The insulation is held off the concrete so the wall can dry, with vapour control on the warm side.

Vapour Barrier Installation Carlton Edmonton | 6 Mil Poly

Vapour barrier details in Carlton that pass inspection

Alberta winters put a large vapour drive from inside to outside, so the barrier belongs on the warm side of the insulation. Getting the position right matters as much as getting it sealed: a second barrier on the cold side traps moisture in the assembly with no way to dry.

Electrical boxes poly-hatted and sealed
Seams lapped at framing and sealed, not just taped
Left ready for inspection before boarding
Window and door returns detailed properly
Rim joists air-sealed before insulating
Poly on the warm side of the insulation

Renovations, and meeting an existing barrier

Continuity across old and new

In an Carlton renovation the new poly has to tie into whatever is already in the wall. A new sheet stopped at the edge of the work leaves an open seam inside the assembly.

What we look for

Whether an existing barrier is present at all, what condition it is in, and whether there is a second one somewhere that would trap moisture between the two. Older renovations quite often have both, and finding that before boarding is worth the hour it takes.

Carlton drywall in context

About Carlton

Carlton is named after Fort Carlton There are several natural areas within the neighbourhood, including a woodlot containing indigenous species located in the northwestern portion of the neighbourhood.

What we see in Carlton

In Carlton the drywall work is first-year settling, basement dev for first owners, Level 5 over builder-grade. We confirm what your home actually needs on site, in writing, before anything starts.

Inspection, and leaving it visible

It gets checked before it is covered

Vapour barrier and air sealing in Carlton are inspected before drywall covers them. We sequence to your inspection date rather than boarding ahead and covering something the inspector needs to see.

If it does not pass

We want the inspector's note directly. Most failures are specific — an unsealed box, a floating seam, a torn return — and they are corrected faster from the actual note than from a second-hand summary.

Never two barriers

The trap

Poly on the room side plus a second impermeable layer behind the insulation leaves any moisture that gets in with no direction to dry.

Where it happens

Renovations, mostly. A new barrier gets added over a wall that already had a foil-faced or kraft-faced layer. We look at what is already in an Carlton wall before adding to it rather than assuming the cavity is bare.

Windows, doors and the returns around them

Where the detail gets fiddly

The return between a window frame and the wall in Carlton is awkward, tight, and often left as a torn edge tucked behind trim.

Why it matters

It is also a cold junction where condensation shows first, usually as staining or mould at the reveal. The poly is cut to fit, sealed to the frame and supported, rather than folded and hoped for.

Electrical boxes, the usual failure point

A hole in the plane

Every outlet and switch in an Carlton exterior wall is a cut in the poly. Left unsealed it is a direct path for moist air into the cavity, and the boxes are usually the coldest spot on the wall.

Poly hats and sealant

Boxes get a poly hat or an air-sealed box, and the poly is sealed to it rather than simply cut around. It is a small detail repeated dozens of times, which is exactly why it gets skipped.

Seams belong on framing

Not floating in a bay

A lap sealed in the middle of a cavity has nothing solid behind it. Any movement or pressure opens it, and it cannot be inspected properly.

How we run it

Sheets are sized so seams land on a stud or plate, lapped, and sealed against solid backing. It uses slightly more material and it is the difference between a barrier that holds and one that is only continuous on the day it was installed.

How it works

Simple, clean, on schedule — Vapour Barrier Installation in Carlton Edmonton

Free quote

We come out to your Carlton Edmonton property, take a real look at the vapour barrier installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every vapour barrier installation quote in Carlton Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the vapour barrier installation in Carlton Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Carlton Edmonton home while we finish the vapour barrier installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished vapour barrier installation with us and you're happy with the result in Carlton Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the vapour barrier installation contractor Carlton Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your vapour barrier installation project in Carlton Edmonton.

Read our reviews on Google

FAQ — Vapour Barrier Installation Carlton Edmonton

Vapour Barrier Installation Carlton Edmonton: your questions answered

Can you install the barrier if someone else did the insulation?: Yes, but we check the insulation first. A barrier over a poorly filled cavity locks the problem in, and once the board is on neither can be corrected without opening the wall.
Why is there staining around my window reveals?: Usually the vapour barrier return at the window was torn or tucked rather than sealed. It is a cold junction, so condensation shows there first — often as staining or mould at the reveal.
Which side does the vapour barrier go on?: The warm side of the insulation. Through an Alberta winter moisture pushes outward from the heated space, and the barrier stops it before it reaches a cold surface where it can condense.
Do the electrical boxes really need sealing?: They are the most common failure point. Every outlet in an exterior wall is a cut in the plane, and unsealed it is a direct path for moist air into the cavity at the coldest part of the wall.
What about outlets on exterior walls?: Each one is a deliberate hole. They need poly hats or airtight boxes sealed to the sheet. Taping poly to the front of an ordinary box does not last once board is fastened over it, and it is the most common leak we find.
Is a basement wall done the same way as an upstairs wall?: No. A basement wall can take moisture from the ground too, so poly detailed like an above-grade wall can trap moisture against the concrete. The insulation is held off the concrete so the wall can dry, with vapour control on the warm side.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Vapour Barrier Installation Carlton Edmonton

Vapour barrier details in Carlton that pass inspection