Does it matter where the sheet meets the ceiling and floor?

It is the whole job. Left loose at the top or bottom plate, warm air simply goes over or under a perfectly installed sheet. The junction into a vaulted ceiling is the most commonly skipped and the wettest point in the room.

Is it a problem to have poly on both sides?

Yes. Two barriers trap moisture between them with no direction to dry. It is a real mistake we still find in renovated Cameron Heights walls, and it stays invisible until the damage shows.

Which side does the vapour barrier go on?

The warm side of the insulation. Through an Alberta winter moisture pushes outward from the heated space, and the barrier stops it before it reaches a cold surface where it can condense.

What if there is already a vapour barrier in the wall?

We tie into it, and we check whether there is a second one somewhere that would trap moisture between the two. Older Cameron Heights renovations quite often have both, and finding that before boarding is worth the hour.

Will this stop water coming through my basement wall?

No, and installing it would hide the evidence. Water coming through a wall is a drainage and waterproofing problem. Vapour control manages moisture in the air, not liquid water, and we will say so rather than board over it.

Can I add poly over insulation that already has a facing?

Usually no. Two retarders leave any moisture that gets in with no direction to dry. We check what is already in the wall before adding to it rather than assuming the cavity is bare.

Vapour Barrier Installation Cameron Heights Edmonton | 6 Mil Poly

Vapour barrier in Cameron Heights, sealed as a continuous plane

A vapour barrier only works as a continuous plane. In Cameron Heights the failures are almost never the sheet itself — they are the electrical boxes, the top and bottom plates, the window returns and the penetrations, where the poly is cut and not resealed.

Left ready for inspection before boarding
Electrical boxes poly-hatted and sealed
Poly on the warm side of the insulation
Window and door returns detailed properly
Rim joists air-sealed before insulating
Seams lapped at framing and sealed, not just taped

Electrical boxes, the usual failure point

A hole in the plane

Every outlet and switch in an Cameron Heights exterior wall is a cut in the poly. Left unsealed it is a direct path for moist air into the cavity, and the boxes are usually the coldest spot on the wall.

Poly hats and sealant

Boxes get a poly hat or an air-sealed box, and the poly is sealed to it rather than simply cut around. It is a small detail repeated dozens of times, which is exactly why it gets skipped.

Cameron Heights drywall in context

About Cameron Heights

Cameron Heights was named after John Cameron, a pioneer and businessman who lived at the north end of the road that now bears his name (Cameron Avenue).

What we see in Cameron Heights

In Cameron Heights the drywall work is first-year settling, basement dev for first owners, Level 5 over builder-grade. We confirm what your home actually needs on site, in writing, before anything starts.

Never two barriers

The trap

Poly on the room side plus a second impermeable layer behind the insulation leaves any moisture that gets in with no direction to dry.

Where it happens

Renovations, mostly. A new barrier gets added over a wall that already had a foil-faced or kraft-faced layer. We look at what is already in an Cameron Heights wall before adding to it rather than assuming the cavity is bare.

Seams belong on framing

Not floating in a bay

A lap sealed in the middle of a cavity has nothing solid behind it. Any movement or pressure opens it, and it cannot be inspected properly.

How we run it

Sheets are sized so seams land on a stud or plate, lapped, and sealed against solid backing. It uses slightly more material and it is the difference between a barrier that holds and one that is only continuous on the day it was installed.

Bathrooms, kitchens and the wet rooms

More moisture, same rules

A Cameron Heights bathroom pushes far more vapour into the wall than a bedroom. The barrier is not different, but the consequences of a gap are larger and show up faster.

Fans and penetrations

The fan housing, the duct and any pot lights all pierce the plane in the wettest room in the house. Those are sealed rather than trimmed around, and we check that the fan actually vents outside rather than into the attic.

Inspecting it before it is covered

Last chance to see it

Once board is on, an Cameron Heights vapour barrier is inaccessible for the life of the wall.

How we work

The barrier gets walked and repaired, every box, every lap, every penetration, before boarding is scheduled, and it is photographed. A tear found before the board goes on costs a piece of tape; found afterwards it costs a wall.

Warm side, always

The one rule everything else follows

The barrier goes on the heated side of the insulation. In an Cameron Heights climate that is the room side of an exterior wall.

Why position decides everything

Put it on the cold side and you have placed a moisture stop exactly where indoor humidity will condense against it, inside the wall, where nothing dries and nothing is visible until the damage is done.

How it works

Simple, clean, on schedule — Vapour Barrier Installation in Cameron Heights Edmonton

Free quote

We come out to your Cameron Heights Edmonton property, take a real look at the vapour barrier installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every vapour barrier installation quote in Cameron Heights Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the vapour barrier installation in Cameron Heights Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Cameron Heights Edmonton home while we finish the vapour barrier installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished vapour barrier installation with us and you're happy with the result in Cameron Heights Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the vapour barrier installation contractor Cameron Heights Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your vapour barrier installation project in Cameron Heights Edmonton.

Read our reviews on Google

FAQ — Vapour Barrier Installation Cameron Heights Edmonton

Vapour Barrier Installation Cameron Heights Edmonton: your questions answered

Does it matter where the sheet meets the ceiling and floor?: It is the whole job. Left loose at the top or bottom plate, warm air simply goes over or under a perfectly installed sheet. The junction into a vaulted ceiling is the most commonly skipped and the wettest point in the room.
Is it a problem to have poly on both sides?: Yes. Two barriers trap moisture between them with no direction to dry. It is a real mistake we still find in renovated Cameron Heights walls, and it stays invisible until the damage shows.
Which side does the vapour barrier go on?: The warm side of the insulation. Through an Alberta winter moisture pushes outward from the heated space, and the barrier stops it before it reaches a cold surface where it can condense.
What if there is already a vapour barrier in the wall?: We tie into it, and we check whether there is a second one somewhere that would trap moisture between the two. Older Cameron Heights renovations quite often have both, and finding that before boarding is worth the hour.
Will this stop water coming through my basement wall?: No, and installing it would hide the evidence. Water coming through a wall is a drainage and waterproofing problem. Vapour control manages moisture in the air, not liquid water, and we will say so rather than board over it.
Can I add poly over insulation that already has a facing?: Usually no. Two retarders leave any moisture that gets in with no direction to dry. We check what is already in the wall before adding to it rather than assuming the cavity is bare.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Vapour Barrier Installation Cameron Heights Edmonton

Vapour barrier in Cameron Heights, sealed as a continuous plane