Does it matter where the sheets overlap?

Yes. A lap must land on solid framing and be sealed with acoustical sealant compressed between layers. An unsupported lap taped across a cavity flexes with pressure changes and works loose.

Is a bathroom done differently?

Same rules, larger consequences. A bathroom pushes far more vapour into the wall, so a gap shows up faster. The fan housing and duct are sealed rather than trimmed around, and we check the fan vents outside rather than into the attic.

Can you install the barrier if someone else did the insulation?

Yes, but we check the insulation first. A barrier over a poorly filled cavity locks the problem in, and once the board is on neither can be corrected without opening the wall.

Why is there staining around my window reveals?

Usually the vapour barrier return at the window was torn or tucked rather than sealed. It is a cold junction, so condensation shows there first — often as staining or mould at the reveal.

What if there is already a vapour barrier in the wall?

We tie into it, and we check whether there is a second one somewhere that would trap moisture between the two. Older Bisset renovations quite often have both, and finding that before boarding is worth the hour.

Which side does the vapour barrier go on?

The warm side of the insulation. Through an Alberta winter moisture pushes outward from the heated space, and the barrier stops it before it reaches a cold surface where it can condense.

Vapour Barrier Installation Bisset Edmonton | 6 Mil Poly

Vapour barrier details in Bisset that pass inspection

Alberta winters put a large vapour drive from inside to outside, so the barrier belongs on the warm side of the insulation. Getting the position right matters as much as getting it sealed: a second barrier on the cold side traps moisture in the assembly with no way to dry.

Electrical boxes poly-hatted and sealed
Poly on the warm side of the insulation
Window and door returns detailed properly
Rim joists air-sealed before insulating
Seams lapped at framing and sealed, not just taped
Left ready for inspection before boarding

Laps, and the framing member behind them

Where sheets meet

A lap needs to land on solid framing and be sealed with acoustical sealant compressed between the layers, not taped in mid-air across a cavity.

Why it fails otherwise

An unsupported lap flexes with pressure changes and the seal works loose. In an Bisset build the sheets are planned so that laps fall on studs rather than wherever the roll ran out.

Bisset drywall in context

About Bisset

Bisset is named for Judge Athelstan Bisset, Q.C.

What we see in Bisset

In Bisset the drywall work is popcorn and stipple ceiling removal, settling+truss-uplift cracks, nail pops, Poly-B repipe patching repipe patching. We confirm what your home actually needs on site, in writing, before anything starts.

Inspecting it before it is covered

Last chance to see it

Once board is on, an Bisset vapour barrier is inaccessible for the life of the wall.

How we work

The barrier gets walked and repaired, every box, every lap, every penetration, before boarding is scheduled, and it is photographed. A tear found before the board goes on costs a piece of tape; found afterwards it costs a wall.

Where the barrier meets the ceiling and the floor

The two continuous edges

A Bisset wall barrier has to be sealed at the top plate and the bottom plate. Left loose, warm air simply goes over or under a perfectly installed sheet.

Cathedral and vaulted areas

Where a wall runs into a vaulted ceiling the junction is awkward and often skipped. It is also the warmest, wettest point in the room because that is where the air collects. It gets detailed properly or the rest of the sheet is decorative.

Inspection, and leaving it visible

It gets checked before it is covered

Vapour barrier and air sealing in Bisset are inspected before drywall covers them. We sequence to your inspection date rather than boarding ahead and covering something the inspector needs to see.

If it does not pass

We want the inspector's note directly. Most failures are specific — an unsealed box, a floating seam, a torn return — and they are corrected faster from the actual note than from a second-hand summary.

Seams belong on framing

Not floating in a bay

A lap sealed in the middle of a cavity has nothing solid behind it. Any movement or pressure opens it, and it cannot be inspected properly.

How we run it

Sheets are sized so seams land on a stud or plate, lapped, and sealed against solid backing. It uses slightly more material and it is the difference between a barrier that holds and one that is only continuous on the day it was installed.

Sealing at the electrical boxes

Every box is a hole

An outlet or switch on an exterior Bisset wall is a deliberate opening straight through the barrier.

The fix

Poly hats or airtight boxes, sealed to the sheet. Taping the poly to the front of an ordinary box does not last, because the board is fastened over it and the seal breaks. This is the single most common leak we find behind finished walls.

How it works

Simple, clean, on schedule — Vapour Barrier Installation in Bisset Edmonton

Free quote

We come out to your Bisset Edmonton property, take a real look at the vapour barrier installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every vapour barrier installation quote in Bisset Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the vapour barrier installation in Bisset Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Bisset Edmonton home while we finish the vapour barrier installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished vapour barrier installation with us and you're happy with the result in Bisset Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the vapour barrier installation contractor Bisset Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your vapour barrier installation project in Bisset Edmonton.

Read our reviews on Google

FAQ — Vapour Barrier Installation Bisset Edmonton

Vapour Barrier Installation Bisset Edmonton: your questions answered

Does it matter where the sheets overlap?: Yes. A lap must land on solid framing and be sealed with acoustical sealant compressed between layers. An unsupported lap taped across a cavity flexes with pressure changes and works loose.
Is a bathroom done differently?: Same rules, larger consequences. A bathroom pushes far more vapour into the wall, so a gap shows up faster. The fan housing and duct are sealed rather than trimmed around, and we check the fan vents outside rather than into the attic.
Can you install the barrier if someone else did the insulation?: Yes, but we check the insulation first. A barrier over a poorly filled cavity locks the problem in, and once the board is on neither can be corrected without opening the wall.
Why is there staining around my window reveals?: Usually the vapour barrier return at the window was torn or tucked rather than sealed. It is a cold junction, so condensation shows there first — often as staining or mould at the reveal.
What if there is already a vapour barrier in the wall?: We tie into it, and we check whether there is a second one somewhere that would trap moisture between the two. Older Bisset renovations quite often have both, and finding that before boarding is worth the hour.
Which side does the vapour barrier go on?: The warm side of the insulation. Through an Alberta winter moisture pushes outward from the heated space, and the barrier stops it before it reaches a cold surface where it can condense.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Vapour Barrier Installation Bisset Edmonton

Vapour barrier details in Bisset that pass inspection