Can you install the barrier if someone else did the insulation?

Yes, but we check the insulation first. A barrier over a poorly filled cavity locks the problem in, and once the board is on neither can be corrected without opening the wall.

Is the vapour barrier the same as an air barrier?

Not by itself. Poly slows vapour diffusion; sealed properly it also slows air, and unsealed it does very little of either. The sealing is what turns a sheet of plastic into a working assembly.

Is a bathroom done differently?

Same rules, larger consequences. A bathroom pushes far more vapour into the wall, so a gap shows up faster. The fan housing and duct are sealed rather than trimmed around, and we check the fan vents outside rather than into the attic.

What if there is already a vapour barrier in the wall?

We tie into it, and we check whether there is a second one somewhere that would trap moisture between the two. Older Allard renovations quite often have both, and finding that before boarding is worth the hour.

Does it matter where the sheet meets the ceiling and floor?

It is the whole job. Left loose at the top or bottom plate, warm air simply goes over or under a perfectly installed sheet. The junction into a vaulted ceiling is the most commonly skipped and the wettest point in the room.

Which side does the vapour barrier go on?

The warm side of the insulation. Through an Alberta winter moisture pushes outward from the heated space, and the barrier stops it before it reaches a cold surface where it can condense.

Vapour Barrier Installation Allard Edmonton | 6 Mil Poly

Poly and air sealing in Allard before the board goes on

A vapour barrier only works as a continuous plane. In Allard the failures are almost never the sheet itself — they are the electrical boxes, the top and bottom plates, the window returns and the penetrations, where the poly is cut and not resealed.

Seams lapped at framing and sealed, not just taped
Rim joists air-sealed before insulating
Electrical boxes poly-hatted and sealed
Window and door returns detailed properly
Left ready for inspection before boarding
Poly on the warm side of the insulation

Laps, and the framing member behind them

Where sheets meet

A lap needs to land on solid framing and be sealed with acoustical sealant compressed between the layers, not taped in mid-air across a cavity.

Why it fails otherwise

An unsupported lap flexes with pressure changes and the seal works loose. In an Allard build the sheets are planned so that laps fall on studs rather than wherever the roll ran out.

Inspecting it before it is covered

Last chance to see it

Once board is on, an Allard vapour barrier is inaccessible for the life of the wall.

How we work

The barrier gets walked and repaired, every box, every lap, every penetration, before boarding is scheduled, and it is photographed. A tear found before the board goes on costs a piece of tape; found afterwards it costs a wall.

Warm side, always

The one rule everything else follows

The barrier goes on the heated side of the insulation. In an Allard climate that is the room side of an exterior wall.

Why position decides everything

Put it on the cold side and you have placed a moisture stop exactly where indoor humidity will condense against it, inside the wall, where nothing dries and nothing is visible until the damage is done.

The parts an inspector looks at first

Predictable list

Electrical boxes, seams landing off framing, the top and bottom plates, window returns and any penetration. Those are where Allard vapour barrier inspections fail, and they fail for the same reasons every time.

Why we sequence to it

We leave the work visible and board after the inspection rather than ahead of it. Covering something an inspector needs to see costs a wall, not an afternoon.

Top plates, bottom plates and the perimeter

The edges do the leaking

The continuous joints at the top and bottom of an Allard wall are longer than every box and lap put together, and they are the easiest to seal well or badly.

What good looks like

Sealant on the plate, poly laid into it and compressed by the framing or the board above, carried around corners rather than cut and butted at every change of direction.

Bathrooms, kitchens and the wet rooms

More moisture, same rules

A Allard bathroom pushes far more vapour into the wall than a bedroom. The barrier is not different, but the consequences of a gap are larger and show up faster.

Fans and penetrations

The fan housing, the duct and any pot lights all pierce the plane in the wettest room in the house. Those are sealed rather than trimmed around, and we check that the fan actually vents outside rather than into the attic.

How it works

Simple, clean, on schedule — Vapour Barrier Installation in Allard Edmonton

Free quote

We come out to your Allard Edmonton property, take a real look at the vapour barrier installation, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every vapour barrier installation quote in Allard Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the vapour barrier installation in Allard Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Allard Edmonton home while we finish the vapour barrier installation to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished vapour barrier installation with us and you're happy with the result in Allard Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the vapour barrier installation contractor Allard Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your vapour barrier installation project in Allard Edmonton.

Read our reviews on Google

FAQ — Vapour Barrier Installation Allard Edmonton

Vapour Barrier Installation Allard Edmonton: your questions answered

Can you install the barrier if someone else did the insulation?: Yes, but we check the insulation first. A barrier over a poorly filled cavity locks the problem in, and once the board is on neither can be corrected without opening the wall.
Is the vapour barrier the same as an air barrier?: Not by itself. Poly slows vapour diffusion; sealed properly it also slows air, and unsealed it does very little of either. The sealing is what turns a sheet of plastic into a working assembly.
Is a bathroom done differently?: Same rules, larger consequences. A bathroom pushes far more vapour into the wall, so a gap shows up faster. The fan housing and duct are sealed rather than trimmed around, and we check the fan vents outside rather than into the attic.
What if there is already a vapour barrier in the wall?: We tie into it, and we check whether there is a second one somewhere that would trap moisture between the two. Older Allard renovations quite often have both, and finding that before boarding is worth the hour.
Does it matter where the sheet meets the ceiling and floor?: It is the whole job. Left loose at the top or bottom plate, warm air simply goes over or under a perfectly installed sheet. The junction into a vaulted ceiling is the most commonly skipped and the wettest point in the room.
Which side does the vapour barrier go on?: The warm side of the insulation. Through an Alberta winter moisture pushes outward from the heated space, and the barrier stops it before it reaches a cold surface where it can condense.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Vapour Barrier Installation Allard Edmonton

Poly and air sealing in Allard before the board goes on