Can you coordinate with my plumber for the re-pipe in Ogilvie Ridge?

Yes. Tell us ahead of the Ogilvie Ridge Poly-B work and we coordinate with the plumber around the inspection dates. This keeps the walls in your Ogilvie Ridge home closed as quickly as possible after the plumbing work is done.

How long does the drywall part take?

Longer than people expect, because it cannot start until the plumbing is signed off and compound cannot be rushed. Board, coats with drying between, sand, prime, paint. Anyone promising all of it in two days is quoting a schedule they will not keep.

How do you handle texture matching after poly-b drywall repair work in Ogilvie Ridge?

Texture matching is part of every repair and patch job we do in Ogilvie Ridge. Whether the surrounding surface is knockdown, smooth or an older pattern, we match it so the repair is not visible under paint.

Do I need to wait for plumbing inspections before you repair the drywall in my Ogilvie Ridge home?

Yes. We do not close any cut-out in your Ogilvie Ridge home until the plumbing re-pipe is done and inspections have passed. Board over an Ogilvie Ridge opening before the inspection and the inspector re-cuts it — double the repair bill. In Ogilvie Ridge we sync with your plumber and slot in right after the inspections.

Poly-B Drywall Repair Ogilvie Ridge Edmonton | Re-Pipe Patching

Poly-B re-pipe drywall repair in Ogilvie Ridge

Poly-B plumbing was installed in Edmonton-area homes from the late 1970s through the mid-1990s. When a plumber does a full re-pipe or repairs a failed fitting in an Ogilvie Ridge home, the job leaves cut-outs in walls and ceilings. Ogilvie Ridge is a premium Whitemud community built with PEX or copper plumbing. Plumbing repair patches here are small scope and the finish expectation is high. We follow the Ogilvie Ridge plumber and the inspections, then close, Level-4 tape and texture-match every opening until the re-pipe is invisible. We cover Ogilvie Ridge, Aspen Gardens, Bearspaw, Blue Quill and surrounding communities, 7 days a week.

Drywall repair after poly-B re-pipe — all cut-outs closed
Dust contained, room protected during repair
Ogilvie Ridge patches finished to Level 4 — bedded tape, built-up coats, a flat sand
Dust contained room by room across the Ogilvie Ridge home, cleaned before we leave
Re-pipe drywall in Ogilvie Ridge — all cut-outs closed, one scope, one invoice
We align with the Ogilvie Ridge plumber and wait on Poly-B inspections
Contained dust throughout the Ogilvie Ridge job, cleanup before we go

Insulation and vapour barrier the pipes went through

Do not just close it

An exterior Ogilvie Ridge wall opened for repiping usually has its insulation disturbed and its vapour barrier cut.

What we restore

Batts refitted properly, the barrier repaired and sealed before board goes back on. Boarding over a torn barrier hides a problem inside the wall that nobody will see until it stains the finish.

Closing up after the repipe, at a price fixed up front

The half of the job nobody quotes

Homeowners are usually given a repipe price with the drywall left as an open question. We give a fixed price at the on-site quote for putting the house back, and the number does not change.

Back to paint-ready

Every joint taped to Level 4, every texture matched precisely, and the surface left paint-ready when we leave. We cover Ogilvie Ridge, Aspen Gardens, Bearspaw, Blue Quill and surrounding communities, with free on-site quotes and a same-day reply, 7 days a week. Call or text ' . emp_phone() . '.

Cutting for access, before it is opened

Where the openings go matters

A plumber cuts where the pipe is. If we are involved before that, openings can often be placed to land on framing, in one plane, and away from corners.

What it saves

A neat rectangle between two studs closes cleanly. A ragged hole across a corner in an Ogilvie Ridge hallway costs far more to make invisible. Ten minutes of coordination changes the repair bill.

What affects the cost of poly-B re-pipe drywall repair in Edmonton?

Patch count, ceiling vs. wall, and texture matching

The main cost drivers for poly-B re-pipe drywall repair in Edmonton are how many cut-outs the plumber left, whether the openings are in walls or ceilings (ceilings take more setup), and how many different textures need to be matched throughout the home. A full re-pipe in a 1970s Edmonton bungalow — one storey, slab-on-grade or crawl space below — can leave 15 to 25 wall and ceiling patches. A two-storey from the same era can leave 25 to 40. We walk the Ogilvie Ridge home, scope every opening and set a fixed price for all of it.

Coordinating around the plumber in Edmonton

Re-pipe jobs go smoothest when the drywall work follows the plumbing directly. We schedule to come in immediately after the plumber is done and inspections have passed — so your Edmonton home is not sitting with open walls for weeks. If you are planning a re-pipe, call us before the plumbing starts and we can coordinate the timing from the beginning.

Scheduling around the water being off

Two trades, one timeline

Drywall cannot start until the plumbing is inspected and signed off, and compound cannot be rushed after that.

What to expect

We give the honest sequence for the Ogilvie Ridge house: plumber, inspection, board, coats with drying between, sand, prime, paint. Anyone promising it all inside two days is quoting a schedule they will not keep.

Poly-B drywall repair work we do across Edmonton

Full re-pipe drywall work in Whitemud’s established communities

Aspen Gardens, Bearspaw, Blue Quill — these are the Edmonton communities where we do consistent full re-pipe drywall work. A typical job in one of these homes involves 15 to 40 wall and ceiling cut-outs across multiple rooms, closets, utility spaces and occasionally crawl spaces. In Ogilvie Ridge we seal each opening, take joints to Level 4 and match texture everywhere. We work room by room so the home stays livable, and we clean up each room completely before we move on.

Single fitting failure patches and newer-community repair work

Not every poly-B call is a full re-pipe. A single fitting failure at a bathroom shutoff or hot water tank connection in a home that has not yet been re-piped leaves a targeted cut-out. We patch it, tape to Level 4 and texture match — same standard as a full re-pipe job, just a single opening. In newer Edmonton communities — Aspen Gardens, Bearspaw, Blue Quill — the calls are small-scope plumbing repair patches where the primary requirement is a clean Level 4 finish and a precise texture match.

How it works

Simple, clean, on schedule — Poly-B Repair in Ogilvie Ridge Edmonton

Free quote

We come out to your Ogilvie Ridge Edmonton property, take a real look at the poly-b repair, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every poly-b repair quote in Ogilvie Ridge Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the poly-b repair in Ogilvie Ridge Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Ogilvie Ridge Edmonton home while we finish the poly-b repair to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished poly-b repair with us and you're happy with the result in Ogilvie Ridge Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the poly-b repair contractor Ogilvie Ridge Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your poly-b repair project in Ogilvie Ridge Edmonton.

Read our reviews on Google

FAQ — Poly-B Drywall Repair Ogilvie Ridge Edmonton

Poly-B Drywall Repair Ogilvie Ridge Edmonton: your questions answered

Can you coordinate with my plumber for the re-pipe in Ogilvie Ridge?: Yes. Tell us ahead of the Ogilvie Ridge Poly-B work and we coordinate with the plumber around the inspection dates. This keeps the walls in your Ogilvie Ridge home closed as quickly as possible after the plumbing work is done.
How long does the drywall part take?: Longer than people expect, because it cannot start until the plumbing is signed off and compound cannot be rushed. Board, coats with drying between, sand, prime, paint. Anyone promising all of it in two days is quoting a schedule they will not keep.
How do you handle texture matching after poly-b drywall repair work in Ogilvie Ridge?: Texture matching is part of every repair and patch job we do in Ogilvie Ridge. Whether the surrounding surface is knockdown, smooth or an older pattern, we match it so the repair is not visible under paint.
Do you do poly-B re-pipe drywall repair in Ogilvie Ridge?: Yes — Ogilvie Ridge is part of our regular service area. We cover Ogilvie Ridge, Aspen Gardens, Bearspaw, Blue Quill and surrounding communities, 7 days a week. Free on-site quotes, fixed prices, same-day reply.
Do you do poly-b drywall repair in Ogilvie Ridge?: Yes — Ogilvie Ridge is part of our regular service area. We cover Ogilvie Ridge, Aspen Gardens, Bearspaw, Blue Quill and surrounding communities, 7 days a week. Free on-site quotes, fixed prices, same-day reply.
Do I need to wait for plumbing inspections before you repair the drywall in my Ogilvie Ridge home?: Yes. We do not close any cut-out in your Ogilvie Ridge home until the plumbing re-pipe is done and inspections have passed. Board over an Ogilvie Ridge opening before the inspection and the inspector re-cuts it — double the repair bill. In Ogilvie Ridge we sync with your plumber and slot in right after the inspections.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Poly-B Drywall Repair Ogilvie Ridge Edmonton

Poly-B re-pipe drywall repair in Ogilvie Ridge