Can I still store things in the attic?

Only over a raised platform. Anything laid straight on the joists compresses the material and cuts a thin channel through the middle of the ceiling. Otherwise a fully insulated attic is not also a storage room.

Can you blow insulation into my walls without opening them?

Often yes — dense-pack through small holes, packed hard enough that it does not slump and leave a cold band at the top. The holes then need filling and finishing, which is drywall work, so we quote that with it rather than surprising you.

Do you seal before blowing?

Yes, and it is the step most often skipped. Loose material laid over an open ceiling penetration hides the leak rather than stopping it, and the warm moist air coming through is what wets the insulation from inside.

Is blown-in better than batts?

In an attic, usually yes, because it flows around trusses, bracing and wiring where batts get cut short or forced and leave gaps. In open framed walls at regular spacing, batts are fine. We recommend by the space, not by what is on the truck.

What if you find old wiring?

If we find wiring that must not be covered, we stop and say so rather than blowing over it. That is an electrician's call, not ours, and it is a real reason a job gets paused rather than finished the same day.

Is it too heavy for my ceiling?

Rarely, but worth thinking about on an older lath ceiling or a long unsupported span. Where the ceiling is old or already sagging we would rather use the lighter material at a sensible depth, and sometimes recommend fixing the ceiling first.

Loose Fill Insulation Walker | Loose Fill Insulation

Blown-in insulation for Walker attics and closed cavities

Loose-fill insulation is blown in rather than cut and fitted, which makes it the right answer wherever a batt cannot go: over an irregular Walker attic floor, around trusses and bracing, and into wall cavities that are already closed. What you are paying for is settled depth spread evenly, and that is a thing which can be measured. Depth markers go in before the hose starts, and we read them at the corners rather than in the middle where it is always deepest.

Depth read back at the corners, not just where the hatch is
Baffles at the eaves so soffit venting stays clear
Existing material assessed — topped up, or removed if it is wet or contaminated
Even coverage carried right out over the top plates
Ceiling penetrations air-sealed first, not buried
Settled depth specified and marked before the hose starts

The material must not block the eaves

Loose material moves

Unlike a batt, blown-in can be pushed by wind washing at the eaves and drift away from where it was placed.

Baffles, every time

Baffles hold it back from the soffit vents and stop wind scouring the edge thin. In an Walker attic that band above the exterior wall is exactly where the house loses heat, so it is the last place to accept a thin spot.

Access, hoses and how much of the house we cross

Practical reality

The machine sits outside and a hose runs to the Walker attic hatch, which usually means through a hallway or a closet.

Keeping it clean

Protected route, sealed hatch surround, the space vacuumed after. It is a dusty trade and the difference between a good crew and a bad one is mostly what the house looks like at the end.

Moisture is what ruins it

Wet insulation is not insulation

Loose-fill that takes moisture packs down, loses most of its value and does not recover when it dries.

Finding the cause first

A damp patch in an Walker attic means a roof leak, a bathroom fan venting into the space, or warm moist air leaking up through the ceiling. Blowing new material over any of those wastes it.

Removing old loose-fill

A vacuum job, not a shovel job

Old blown-in comes out with a vacuum and hose into sealed bags, because disturbing decades of settled material makes a great deal of airborne dust.

What it buys

A clean deck to air-seal properly and, in older Walker homes, the chance to see the ceiling structure and any past leaks before they are covered again.

Pot lights buried in loose material

A heat question

Older recessed fixtures are not all rated to be covered, and loose-fill packs right against them.

What we check

Whether the Walker fixtures are rated for insulation contact. Where they are not, they get a proper clearance detail rather than being buried and hoped about — and that detail is also a sealed one, so it does not become a new air leak.

How it works

Simple, clean, on schedule — Drywall in Edmonton

Free quote

We come out to your Edmonton property, take a real look at the drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every drywall quote in Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the drywall in Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Edmonton home while we finish the drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished drywall with us and you're happy with the result in Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the drywall contractor Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your drywall project in Edmonton.

Read our reviews on Google

FAQ — Loose Fill Insulation Walker

Loose Fill Insulation Walker: your questions answered

Can I still store things in the attic?: Only over a raised platform. Anything laid straight on the joists compresses the material and cuts a thin channel through the middle of the ceiling. Otherwise a fully insulated attic is not also a storage room.
Can you blow insulation into my walls without opening them?: Often yes — dense-pack through small holes, packed hard enough that it does not slump and leave a cold band at the top. The holes then need filling and finishing, which is drywall work, so we quote that with it rather than surprising you.
Do you seal before blowing?: Yes, and it is the step most often skipped. Loose material laid over an open ceiling penetration hides the leak rather than stopping it, and the warm moist air coming through is what wets the insulation from inside.
Is blown-in better than batts?: In an attic, usually yes, because it flows around trusses, bracing and wiring where batts get cut short or forced and leave gaps. In open framed walls at regular spacing, batts are fine. We recommend by the space, not by what is on the truck.
What if you find old wiring?: If we find wiring that must not be covered, we stop and say so rather than blowing over it. That is an electrician's call, not ours, and it is a real reason a job gets paused rather than finished the same day.
Is it too heavy for my ceiling?: Rarely, but worth thinking about on an older lath ceiling or a long unsupported span. Where the ceiling is old or already sagging we would rather use the lighter material at a sensible depth, and sometimes recommend fixing the ceiling first.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Loose Fill Insulation Walker

Blown-in insulation for Walker attics and closed cavities