Dusty — the machine sits outside and a hose runs through the house to the hatch. We protect the route, seal around the hatch and vacuum afterwards. What the house looks like at the end is most of the difference between crews.

Can you just add over what is already up there?

Usually, and it is the best value if the existing material is dry, even and uncontaminated. If it is damp, matted, rodent-affected or hiding unsealed penetrations, adding over it buries the problem — we tell you which one we found.

Will it block my soffit vents?

Not if baffles go in first. Loose material can also be pushed around by wind at the eaves, so the baffles both hold it clear of the vents and stop the edge being scoured thin — which is exactly where the house loses heat.

Does loose-fill settle?

Yes, which is why it is specified at a settled depth rather than how it looks on the day. A job blown to look right can measure short a year later. We work to the published settled figure and mark it before starting.

What do I get when the job is done?

The bag count, the target settled depth, and photographs of the finished space including the corners and the eaves — so you can confirm years later what was actually installed instead of probing a hole and guessing.

What about my pot lights?

Older recessed fixtures are not all rated to be covered and loose-fill packs right against them. We check the rating, and where they are not rated they get a proper clearance detail that is also sealed, rather than being buried and hoped about.

Loose Fill Insulation Strathcona Edmonton | Blown-In

Loose-fill insulation in Strathcona, measured rather than estimated

Blown-in material fills the awkward parts of an Strathcona building that batts leave gapped — around cross-bracing, over the top plates of interior walls, into the shallow triangle at the eaves. It settles over time, which is why it is specified at a settled depth rather than the depth it looks on the day. Air sealing comes first, because loose material laid over an open ceiling penetration hides the leak instead of stopping it.

Depth read back at the corners, not just where the hatch is
Ceiling penetrations air-sealed first, not buried
Existing material assessed — topped up, or removed if it is wet or contaminated
Even coverage carried right out over the top plates
Settled depth specified and marked before the hose starts
Baffles at the eaves so soffit venting stays clear

Blowing into a wall that is already closed

Dense-pack

Loose-fill can be blown into closed Strathcona wall cavities through small holes, packed to a density that stops it slumping and leaving a cold band at the top.

Where it fits

It suits an older home you do not want to open up. It needs the holes made, filled and finished afterwards, which is drywall work — so quote the patching with it rather than discovering it later.

Strathcona drywall in context

About Strathcona

Strathcona was named for Lord Strathcona, Hudson Bay Company Governor (1889-1914) and the man chosen to drive the "last spike" of the CPR transcontinental railway.

What we see in Strathcona

In Strathcona the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Topping up what is already there

Usually the best value

Dry, uncontaminated existing material does not need removing. Blowing over it to reach the target settled depth costs a fraction of a strip-and-replace.

When we say no

If it is damp, matted flat, rodent-affected, or hiding unsealed penetrations, adding over it buries a problem. We say which one we found in the Strathcona attic and price both options.

Loose-fill or batts, decided on the space

Not a loyalty question

Batts suit open framing at regular spacing. Loose-fill suits irregular, obstructed or already-closed spaces.

How we quote it

We look at the Strathcona space and recommend the one that fits it, including saying when a mix is right — batts in the open framed walls, blown-in above the ceiling. Nobody should be sold the material the truck happens to carry.

Moisture is what ruins it

Wet insulation is not insulation

Loose-fill that takes moisture packs down, loses most of its value and does not recover when it dries.

Finding the cause first

A damp patch in an Strathcona attic means a roof leak, a bathroom fan venting into the space, or warm moist air leaking up through the ceiling. Blowing new material over any of those wastes it.

Removing old loose-fill

A vacuum job, not a shovel job

Old blown-in comes out with a vacuum and hose into sealed bags, because disturbing decades of settled material makes a great deal of airborne dust.

What it buys

A clean deck to air-seal properly and, in older Strathcona homes, the chance to see the ceiling structure and any past leaks before they are covered again.

What we hand over at the end

Evidence, not assurances

Bag count, target settled depth, and photographs of the finished Strathcona space including the corners and the eaves.

Why it matters later

It is what lets you or anyone else confirm years afterwards what was actually installed, rather than probing a hole in the ceiling and guessing.

How it works

Simple, clean, on schedule — Drywall in Edmonton

Free quote

We come out to your Edmonton property, take a real look at the drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every drywall quote in Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the drywall in Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Edmonton home while we finish the drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished drywall with us and you're happy with the result in Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the drywall contractor Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your drywall project in Edmonton.

Read our reviews on Google

FAQ — Loose Fill Insulation Strathcona Edmonton

Loose Fill Insulation Strathcona Edmonton: your questions answered

How messy is it?: Dusty — the machine sits outside and a hose runs through the house to the hatch. We protect the route, seal around the hatch and vacuum afterwards. What the house looks like at the end is most of the difference between crews.
Can you just add over what is already up there?: Usually, and it is the best value if the existing material is dry, even and uncontaminated. If it is damp, matted, rodent-affected or hiding unsealed penetrations, adding over it buries the problem — we tell you which one we found.
Will it block my soffit vents?: Not if baffles go in first. Loose material can also be pushed around by wind at the eaves, so the baffles both hold it clear of the vents and stop the edge being scoured thin — which is exactly where the house loses heat.
Does loose-fill settle?: Yes, which is why it is specified at a settled depth rather than how it looks on the day. A job blown to look right can measure short a year later. We work to the published settled figure and mark it before starting.
What do I get when the job is done?: The bag count, the target settled depth, and photographs of the finished space including the corners and the eaves — so you can confirm years later what was actually installed instead of probing a hole and guessing.
What about my pot lights?: Older recessed fixtures are not all rated to be covered and loose-fill packs right against them. We check the rating, and where they are not rated they get a proper clearance detail that is also sealed, rather than being buried and hoped about.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Loose Fill Insulation Strathcona Edmonton

Loose-fill insulation in Strathcona, measured rather than estimated