What do I get when the job is done?

The bag count, the target settled depth, and photographs of the finished space including the corners and the eaves — so you can confirm years later what was actually installed instead of probing a hole and guessing.

Can you just add over what is already up there?

Usually, and it is the best value if the existing material is dry, even and uncontaminated. If it is damp, matted, rodent-affected or hiding unsealed penetrations, adding over it buries the problem — we tell you which one we found.

How do I know I got what I paid for?

Bag count. Every bag states the area it covers at a given depth, so bags used divided by area is exactly what went in. We keep them, mark the target settled depth, and read the depth back at the corners rather than the middle.

Does loose-fill settle?

Yes, which is why it is specified at a settled depth rather than how it looks on the day. A job blown to look right can measure short a year later. We work to the published settled figure and mark it before starting.

Is blown-in better than batts?

In an attic, usually yes, because it flows around trusses, bracing and wiring where batts get cut short or forced and leave gaps. In open framed walls at regular spacing, batts are fine. We recommend by the space, not by what is on the truck.

Cellulose or fibreglass?

Both work. Cellulose is denser, packs into odd shapes and resists air movement through it better; fibreglass is lighter, which matters on a ceiling of uncertain strength. Where there is existing material, matching it is usually simpler than layering the other over it.

Loose Fill Insulation Sherwood Edmonton | Blown-In

Loose-fill insulation in Sherwood, measured rather than estimated

Loose-fill insulation is blown in rather than cut and fitted, which makes it the right answer wherever a batt cannot go: over an irregular Sherwood attic floor, around trusses and bracing, and into wall cavities that are already closed. What you are paying for is settled depth spread evenly, and that is a thing which can be measured. Depth markers go in before the hose starts, and we read them at the corners rather than in the middle where it is always deepest.

Baffles at the eaves so soffit venting stays clear
Existing material assessed — topped up, or removed if it is wet or contaminated
Ceiling penetrations air-sealed first, not buried
Settled depth specified and marked before the hose starts
Even coverage carried right out over the top plates
Depth read back at the corners, not just where the hatch is

The material must not block the eaves

Loose material moves

Unlike a batt, blown-in can be pushed by wind washing at the eaves and drift away from where it was placed.

Baffles, every time

Baffles hold it back from the soffit vents and stop wind scouring the edge thin. In an Sherwood attic that band above the exterior wall is exactly where the house loses heat, so it is the last place to accept a thin spot.

Sherwood drywall in context

About Sherwood

Annexed to the City in 1964, Sherwood was once part of the Town of Jasper Place.

What we see in Sherwood

In Sherwood the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Pot lights buried in loose material

A heat question

Older recessed fixtures are not all rated to be covered, and loose-fill packs right against them.

What we check

Whether the Sherwood fixtures are rated for insulation contact. Where they are not, they get a proper clearance detail rather than being buried and hoped about — and that detail is also a sealed one, so it does not become a new air leak.

Blowing into a wall that is already closed

Dense-pack

Loose-fill can be blown into closed Sherwood wall cavities through small holes, packed to a density that stops it slumping and leaving a cold band at the top.

Where it fits

It suits an older home you do not want to open up. It needs the holes made, filled and finished afterwards, which is drywall work — so quote the patching with it rather than discovering it later.

Working in a cathedral or a low attic

Not every space suits it

A vented sloped ceiling needs its air channel kept clear, and a shallow attic may not have room for the hose or the depth.

Being straight about it

Where an Sherwood roof space cannot take a proper depth without blocking ventilation, we say what the space can actually achieve instead of quoting a number the geometry will not allow.

Topping up what is already there

Usually the best value

Dry, uncontaminated existing material does not need removing. Blowing over it to reach the target settled depth costs a fraction of a strip-and-replace.

When we say no

If it is damp, matted flat, rodent-affected, or hiding unsealed penetrations, adding over it buries a problem. We say which one we found in the Sherwood attic and price both options.

Bath fans and the ducts above the ceiling

A very common find

Fans discharging into the attic instead of outside, or a duct that has come off its boot and is blowing into the insulation.

Why it belongs in this job

It is the fastest way to soak an Sherwood attic from inside. We look for it while the space is open and flag it before covering anything, rather than blowing over the top.

How it works

Simple, clean, on schedule — Drywall in Edmonton

Free quote

We come out to your Edmonton property, take a real look at the drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every drywall quote in Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the drywall in Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Edmonton home while we finish the drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished drywall with us and you're happy with the result in Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the drywall contractor Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your drywall project in Edmonton.

Read our reviews on Google

FAQ — Loose Fill Insulation Sherwood Edmonton

Loose Fill Insulation Sherwood Edmonton: your questions answered

What do I get when the job is done?: The bag count, the target settled depth, and photographs of the finished space including the corners and the eaves — so you can confirm years later what was actually installed instead of probing a hole and guessing.
Can you just add over what is already up there?: Usually, and it is the best value if the existing material is dry, even and uncontaminated. If it is damp, matted, rodent-affected or hiding unsealed penetrations, adding over it buries the problem — we tell you which one we found.
How do I know I got what I paid for?: Bag count. Every bag states the area it covers at a given depth, so bags used divided by area is exactly what went in. We keep them, mark the target settled depth, and read the depth back at the corners rather than the middle.
Does loose-fill settle?: Yes, which is why it is specified at a settled depth rather than how it looks on the day. A job blown to look right can measure short a year later. We work to the published settled figure and mark it before starting.
Is blown-in better than batts?: In an attic, usually yes, because it flows around trusses, bracing and wiring where batts get cut short or forced and leave gaps. In open framed walls at regular spacing, batts are fine. We recommend by the space, not by what is on the truck.
Cellulose or fibreglass?: Both work. Cellulose is denser, packs into odd shapes and resists air movement through it better; fibreglass is lighter, which matters on a ceiling of uncertain strength. Where there is existing material, matching it is usually simpler than layering the other over it.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Loose Fill Insulation Sherwood Edmonton

Loose-fill insulation in Sherwood, measured rather than estimated