Can I still store things in the attic?

Only over a raised platform. Anything laid straight on the joists compresses the material and cuts a thin channel through the middle of the ceiling. Otherwise a fully insulated attic is not also a storage room.

Can you just add over what is already up there?

Usually, and it is the best value if the existing material is dry, even and uncontaminated. If it is damp, matted, rodent-affected or hiding unsealed penetrations, adding over it buries the problem — we tell you which one we found.

Does loose-fill settle?

Yes, which is why it is specified at a settled depth rather than how it looks on the day. A job blown to look right can measure short a year later. We work to the published settled figure and mark it before starting.

Will it block my soffit vents?

Not if baffles go in first. Loose material can also be pushed around by wind at the eaves, so the baffles both hold it clear of the vents and stop the edge being scoured thin — which is exactly where the house loses heat.

Does the attic hatch need doing too?

Yes, or it undoes a good part of the rest. It needs an insulated weatherstripped cover and a dam around the opening tall enough to hold the new depth back from spilling through every time it is opened.

Can you blow insulation into my walls without opening them?

Often yes — dense-pack through small holes, packed hard enough that it does not slump and leave a cold band at the top. The holes then need filling and finishing, which is drywall work, so we quote that with it rather than surprising you.

Loose Fill Insulation Sherbrooke Edmonton | Blown-In

Loose-fill insulation in Sherbrooke, measured rather than estimated

Blown-in material fills the awkward parts of an Sherbrooke building that batts leave gapped — around cross-bracing, over the top plates of interior walls, into the shallow triangle at the eaves. It settles over time, which is why it is specified at a settled depth rather than the depth it looks on the day. Air sealing comes first, because loose material laid over an open ceiling penetration hides the leak instead of stopping it.

Baffles at the eaves so soffit venting stays clear
Depth read back at the corners, not just where the hatch is
Even coverage carried right out over the top plates
Existing material assessed — topped up, or removed if it is wet or contaminated
Settled depth specified and marked before the hose starts
Ceiling penetrations air-sealed first, not buried

Bag count is the honest check

Coverage is arithmetic

Every bag states the area it covers at a given depth. Bags used, divided by area, tells you exactly what was installed.

Why we keep them

Depth can be probed in a few spots and averaged; the bag count cannot be argued with. On an Sherbrooke attic it is the simplest proof that what was quoted is what went in.

Sherbrooke drywall in context

About Sherbrooke

Sherbrooke dates to the City's earliest land boom in 1906.

What we see in Sherbrooke

In Sherbrooke the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Moisture is what ruins it

Wet insulation is not insulation

Loose-fill that takes moisture packs down, loses most of its value and does not recover when it dries.

Finding the cause first

A damp patch in an Sherbrooke attic means a roof leak, a bathroom fan venting into the space, or warm moist air leaking up through the ceiling. Blowing new material over any of those wastes it.

Removing old loose-fill

A vacuum job, not a shovel job

Old blown-in comes out with a vacuum and hose into sealed bags, because disturbing decades of settled material makes a great deal of airborne dust.

What it buys

A clean deck to air-seal properly and, in older Sherbrooke homes, the chance to see the ceiling structure and any past leaks before they are covered again.

What we hand over at the end

Evidence, not assurances

Bag count, target settled depth, and photographs of the finished Sherbrooke space including the corners and the eaves.

Why it matters later

It is what lets you or anyone else confirm years afterwards what was actually installed, rather than probing a hole in the ceiling and guessing.

Topping up what is already there

Usually the best value

Dry, uncontaminated existing material does not need removing. Blowing over it to reach the target settled depth costs a fraction of a strip-and-replace.

When we say no

If it is damp, matted flat, rodent-affected, or hiding unsealed penetrations, adding over it buries a problem. We say which one we found in the Sherbrooke attic and price both options.

The material must not block the eaves

Loose material moves

Unlike a batt, blown-in can be pushed by wind washing at the eaves and drift away from where it was placed.

Baffles, every time

Baffles hold it back from the soffit vents and stop wind scouring the edge thin. In an Sherbrooke attic that band above the exterior wall is exactly where the house loses heat, so it is the last place to accept a thin spot.

How it works

Simple, clean, on schedule — Drywall in Edmonton

Free quote

We come out to your Edmonton property, take a real look at the drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every drywall quote in Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the drywall in Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Edmonton home while we finish the drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished drywall with us and you're happy with the result in Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the drywall contractor Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your drywall project in Edmonton.

Read our reviews on Google

FAQ — Loose Fill Insulation Sherbrooke Edmonton

Loose Fill Insulation Sherbrooke Edmonton: your questions answered

Can I still store things in the attic?: Only over a raised platform. Anything laid straight on the joists compresses the material and cuts a thin channel through the middle of the ceiling. Otherwise a fully insulated attic is not also a storage room.
Can you just add over what is already up there?: Usually, and it is the best value if the existing material is dry, even and uncontaminated. If it is damp, matted, rodent-affected or hiding unsealed penetrations, adding over it buries the problem — we tell you which one we found.
Does loose-fill settle?: Yes, which is why it is specified at a settled depth rather than how it looks on the day. A job blown to look right can measure short a year later. We work to the published settled figure and mark it before starting.
Will it block my soffit vents?: Not if baffles go in first. Loose material can also be pushed around by wind at the eaves, so the baffles both hold it clear of the vents and stop the edge being scoured thin — which is exactly where the house loses heat.
Does the attic hatch need doing too?: Yes, or it undoes a good part of the rest. It needs an insulated weatherstripped cover and a dam around the opening tall enough to hold the new depth back from spilling through every time it is opened.
Can you blow insulation into my walls without opening them?: Often yes — dense-pack through small holes, packed hard enough that it does not slump and leave a cold band at the top. The holes then need filling and finishing, which is drywall work, so we quote that with it rather than surprising you.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Loose Fill Insulation Sherbrooke Edmonton

Loose-fill insulation in Sherbrooke, measured rather than estimated