How do I know I got what I paid for?

Bag count. Every bag states the area it covers at a given depth, so bags used divided by area is exactly what went in. We keep them, mark the target settled depth, and read the depth back at the corners rather than the middle.

Do you seal before blowing?

Yes, and it is the step most often skipped. Loose material laid over an open ceiling penetration hides the leak rather than stopping it, and the warm moist air coming through is what wets the insulation from inside.

Cellulose or fibreglass?

Both work. Cellulose is denser, packs into odd shapes and resists air movement through it better; fibreglass is lighter, which matters on a ceiling of uncertain strength. Where there is existing material, matching it is usually simpler than layering the other over it.

Is it too heavy for my ceiling?

Rarely, but worth thinking about on an older lath ceiling or a long unsupported span. Where the ceiling is old or already sagging we would rather use the lighter material at a sensible depth, and sometimes recommend fixing the ceiling first.

Can you blow insulation into my walls without opening them?

Often yes — dense-pack through small holes, packed hard enough that it does not slump and leave a cold band at the top. The holes then need filling and finishing, which is drywall work, so we quote that with it rather than surprising you.

Will it block my soffit vents?

Not if baffles go in first. Loose material can also be pushed around by wind at the eaves, so the baffles both hold it clear of the vents and stop the edge being scoured thin — which is exactly where the house loses heat.

Loose Fill Insulation Prince Charles

Blown-in insulation for Prince Charles attics and closed cavities

Blown-in material fills the awkward parts of an Prince Charles building that batts leave gapped — around cross-bracing, over the top plates of interior walls, into the shallow triangle at the eaves. It settles over time, which is why it is specified at a settled depth rather than the depth it looks on the day. Air sealing comes first, because loose material laid over an open ceiling penetration hides the leak instead of stopping it.

Settled depth specified and marked before the hose starts
Ceiling penetrations air-sealed first, not buried
Baffles at the eaves so soffit venting stays clear
Even coverage carried right out over the top plates
Existing material assessed — topped up, or removed if it is wet or contaminated
Depth read back at the corners, not just where the hatch is

Topping up what is already there

Usually the best value

Dry, uncontaminated existing material does not need removing. Blowing over it to reach the target settled depth costs a fraction of a strip-and-replace.

When we say no

If it is damp, matted flat, rodent-affected, or hiding unsealed penetrations, adding over it buries a problem. We say which one we found in the Prince Charles attic and price both options.

Prince Charles drywall in context

About Prince Charles

Situated on land once own by prominent citizens N.

What we see in Prince Charles

In Prince Charles the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Settled depth versus installed depth

The number that counts

Loose-fill settles after installation. A job blown to look right on the day can be measurably short a year later.

How it is specified

The manufacturer publishes a settled depth and the bag count needed to reach it over a given area. We work to that and mark it, rather than blowing until the Prince Charles attic looks full.

Moisture is what ruins it

Wet insulation is not insulation

Loose-fill that takes moisture packs down, loses most of its value and does not recover when it dries.

Finding the cause first

A damp patch in an Prince Charles attic means a roof leak, a bathroom fan venting into the space, or warm moist air leaking up through the ceiling. Blowing new material over any of those wastes it.

Filling around bracing and trusses

Why batts fail here

Truss webs, cross-bracing and wiring turn an Prince Charles attic floor into a shape no rectangle fits. Batts get cut short or forced, leaving gaps.

What blown-in does

It flows around all of it and fills to a consistent depth. This is the single clearest reason to choose loose-fill over batts above a ceiling.

The material must not block the eaves

Loose material moves

Unlike a batt, blown-in can be pushed by wind washing at the eaves and drift away from where it was placed.

Baffles, every time

Baffles hold it back from the soffit vents and stop wind scouring the edge thin. In an Prince Charles attic that band above the exterior wall is exactly where the house loses heat, so it is the last place to accept a thin spot.

How it works

Simple, clean, on schedule — Drywall in Edmonton

Free quote

We come out to your Edmonton property, take a real look at the drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every drywall quote in Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the drywall in Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Edmonton home while we finish the drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished drywall with us and you're happy with the result in Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the drywall contractor Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your drywall project in Edmonton.

Read our reviews on Google

FAQ — Loose Fill Insulation Prince Charles