Will it block my soffit vents?

Not if baffles go in first. Loose material can also be pushed around by wind at the eaves, so the baffles both hold it clear of the vents and stop the edge being scoured thin — which is exactly where the house loses heat.

Can I still store things in the attic?

Only over a raised platform. Anything laid straight on the joists compresses the material and cuts a thin channel through the middle of the ceiling. Otherwise a fully insulated attic is not also a storage room.

What about my pot lights?

Older recessed fixtures are not all rated to be covered and loose-fill packs right against them. We check the rating, and where they are not rated they get a proper clearance detail that is also sealed, rather than being buried and hoped about.

Can you blow insulation into my walls without opening them?

Often yes — dense-pack through small holes, packed hard enough that it does not slump and leave a cold band at the top. The holes then need filling and finishing, which is drywall work, so we quote that with it rather than surprising you.

What if you find old wiring?

If we find wiring that must not be covered, we stop and say so rather than blowing over it. That is an electrician's call, not ours, and it is a real reason a job gets paused rather than finished the same day.

How do I know I got what I paid for?

Bag count. Every bag states the area it covers at a given depth, so bags used divided by area is exactly what went in. We keep them, mark the target settled depth, and read the depth back at the corners rather than the middle.

Loose Fill Insulation Ormsby Place Edmonton | Blown-In

Loose-fill insulation in Ormsby Place, measured rather than estimated

Blown-in material fills the awkward parts of an Ormsby Place building that batts leave gapped — around cross-bracing, over the top plates of interior walls, into the shallow triangle at the eaves. It settles over time, which is why it is specified at a settled depth rather than the depth it looks on the day. Air sealing comes first, because loose material laid over an open ceiling penetration hides the leak instead of stopping it.

Existing material assessed — topped up, or removed if it is wet or contaminated
Settled depth specified and marked before the hose starts
Depth read back at the corners, not just where the hatch is
Ceiling penetrations air-sealed first, not buried
Baffles at the eaves so soffit venting stays clear
Even coverage carried right out over the top plates

Moisture is what ruins it

Wet insulation is not insulation

Loose-fill that takes moisture packs down, loses most of its value and does not recover when it dries.

Finding the cause first

A damp patch in an Ormsby Place attic means a roof leak, a bathroom fan venting into the space, or warm moist air leaking up through the ceiling. Blowing new material over any of those wastes it.

Ormsby Place drywall in context

About Ormsby Place

Named for the man responsible for developing Edmonton's grid system of numbering streets and avenues, Ormsby Place is located in the City's west end.

What we see in Ormsby Place

In Ormsby Place the drywall work is popcorn and stipple ceiling removal, settling+truss-uplift cracks, nail pops, Poly-B repipe patching repipe patching. We confirm what your home actually needs on site, in writing, before anything starts.

Loose-fill or batts, decided on the space

Not a loyalty question

Batts suit open framing at regular spacing. Loose-fill suits irregular, obstructed or already-closed spaces.

How we quote it

We look at the Ormsby Place space and recommend the one that fits it, including saying when a mix is right — batts in the open framed walls, blown-in above the ceiling. Nobody should be sold the material the truck happens to carry.

Topping up what is already there

Usually the best value

Dry, uncontaminated existing material does not need removing. Blowing over it to reach the target settled depth costs a fraction of a strip-and-replace.

When we say no

If it is damp, matted flat, rodent-affected, or hiding unsealed penetrations, adding over it buries a problem. We say which one we found in the Ormsby Place attic and price both options.

Cellulose or fibreglass, and when it matters

Two common materials

Cellulose is recycled paper treated for fire and pests; loose-fill fibreglass is the same glass wool as a batt, chopped. Both work.

How we choose for an Ormsby Place attic

Cellulose is denser, packs into odd shapes well and resists air movement through it better. Fibreglass is lighter, which matters on a ceiling of uncertain strength. Where the existing material is one of them, matching it is usually simpler than layering the other over top.

The material must not block the eaves

Loose material moves

Unlike a batt, blown-in can be pushed by wind washing at the eaves and drift away from where it was placed.

Baffles, every time

Baffles hold it back from the soffit vents and stop wind scouring the edge thin. In an Ormsby Place attic that band above the exterior wall is exactly where the house loses heat, so it is the last place to accept a thin spot.

Access, hoses and how much of the house we cross

Practical reality

The machine sits outside and a hose runs to the Ormsby Place attic hatch, which usually means through a hallway or a closet.

Keeping it clean

Protected route, sealed hatch surround, the space vacuumed after. It is a dusty trade and the difference between a good crew and a bad one is mostly what the house looks like at the end.

How it works

Simple, clean, on schedule — Drywall in Edmonton

Free quote

We come out to your Edmonton property, take a real look at the drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every drywall quote in Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the drywall in Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Edmonton home while we finish the drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished drywall with us and you're happy with the result in Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the drywall contractor Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your drywall project in Edmonton.

Read our reviews on Google

FAQ — Loose Fill Insulation Ormsby Place Edmonton

Loose Fill Insulation Ormsby Place Edmonton: your questions answered

Will it block my soffit vents?: Not if baffles go in first. Loose material can also be pushed around by wind at the eaves, so the baffles both hold it clear of the vents and stop the edge being scoured thin — which is exactly where the house loses heat.
Can I still store things in the attic?: Only over a raised platform. Anything laid straight on the joists compresses the material and cuts a thin channel through the middle of the ceiling. Otherwise a fully insulated attic is not also a storage room.
What about my pot lights?: Older recessed fixtures are not all rated to be covered and loose-fill packs right against them. We check the rating, and where they are not rated they get a proper clearance detail that is also sealed, rather than being buried and hoped about.
Can you blow insulation into my walls without opening them?: Often yes — dense-pack through small holes, packed hard enough that it does not slump and leave a cold band at the top. The holes then need filling and finishing, which is drywall work, so we quote that with it rather than surprising you.
What if you find old wiring?: If we find wiring that must not be covered, we stop and say so rather than blowing over it. That is an electrician's call, not ours, and it is a real reason a job gets paused rather than finished the same day.
How do I know I got what I paid for?: Bag count. Every bag states the area it covers at a given depth, so bags used divided by area is exactly what went in. We keep them, mark the target settled depth, and read the depth back at the corners rather than the middle.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Loose Fill Insulation Ormsby Place Edmonton

Loose-fill insulation in Ormsby Place, measured rather than estimated