Do you seal before blowing?

Yes, and it is the step most often skipped. Loose material laid over an open ceiling penetration hides the leak rather than stopping it, and the warm moist air coming through is what wets the insulation from inside.

Is blown-in better than batts?

In an attic, usually yes, because it flows around trusses, bracing and wiring where batts get cut short or forced and leave gaps. In open framed walls at regular spacing, batts are fine. We recommend by the space, not by what is on the truck.

Can you just add over what is already up there?

Usually, and it is the best value if the existing material is dry, even and uncontaminated. If it is damp, matted, rodent-affected or hiding unsealed penetrations, adding over it buries the problem — we tell you which one we found.

What if you find old wiring?

If we find wiring that must not be covered, we stop and say so rather than blowing over it. That is an electrician's call, not ours, and it is a real reason a job gets paused rather than finished the same day.

Will it block my soffit vents?

Not if baffles go in first. Loose material can also be pushed around by wind at the eaves, so the baffles both hold it clear of the vents and stop the edge being scoured thin — which is exactly where the house loses heat.

Can you blow insulation into my walls without opening them?

Often yes — dense-pack through small holes, packed hard enough that it does not slump and leave a cold band at the top. The holes then need filling and finishing, which is drywall work, so we quote that with it rather than surprising you.

Loose Fill Insulation Kirkness Edmonton | Blown-In

Loose-fill insulation in Kirkness — settled depth is what you are buying

Loose-fill insulation is blown in rather than cut and fitted, which makes it the right answer wherever a batt cannot go: over an irregular Kirkness attic floor, around trusses and bracing, and into wall cavities that are already closed. What you are paying for is settled depth spread evenly, and that is a thing which can be measured. Depth markers go in before the hose starts, and we read them at the corners rather than in the middle where it is always deepest.

Depth read back at the corners, not just where the hatch is
Ceiling penetrations air-sealed first, not buried
Baffles at the eaves so soffit venting stays clear
Even coverage carried right out over the top plates
Settled depth specified and marked before the hose starts
Existing material assessed — topped up, or removed if it is wet or contaminated

Pot lights buried in loose material

A heat question

Older recessed fixtures are not all rated to be covered, and loose-fill packs right against them.

What we check

Whether the Kirkness fixtures are rated for insulation contact. Where they are not, they get a proper clearance detail rather than being buried and hoped about — and that detail is also a sealed one, so it does not become a new air leak.

Kirkness drywall in context

About Kirkness

Located in the Clareview district, this area is named for James Kirkness, a Hudson's Bay Company employee who came here from Scotland in 1866.

What we see in Kirkness

In Kirkness the drywall work is popcorn and stipple ceiling removal, settling+truss-uplift cracks, nail pops, Poly-B repipe patching repipe patching. We confirm what your home actually needs on site, in writing, before anything starts.

Access, hoses and how much of the house we cross

Practical reality

The machine sits outside and a hose runs to the Kirkness attic hatch, which usually means through a hallway or a closet.

Keeping it clean

Protected route, sealed hatch surround, the space vacuumed after. It is a dusty trade and the difference between a good crew and a bad one is mostly what the house looks like at the end.

What it does for sound

A side benefit

A deep layer of loose-fill over an Kirkness ceiling noticeably reduces airborne noise from outside — traffic, aircraft, neighbours.

Being clear about limits

It does very little for footsteps from a floor above, which travel through structure. If quieting the house is the real goal we would rather say which half this fixes.

Removing old loose-fill

A vacuum job, not a shovel job

Old blown-in comes out with a vacuum and hose into sealed bags, because disturbing decades of settled material makes a great deal of airborne dust.

What it buys

A clean deck to air-seal properly and, in older Kirkness homes, the chance to see the ceiling structure and any past leaks before they are covered again.

Loose-fill or batts, decided on the space

Not a loyalty question

Batts suit open framing at regular spacing. Loose-fill suits irregular, obstructed or already-closed spaces.

How we quote it

We look at the Kirkness space and recommend the one that fits it, including saying when a mix is right — batts in the open framed walls, blown-in above the ceiling. Nobody should be sold the material the truck happens to carry.

Bath fans and the ducts above the ceiling

A very common find

Fans discharging into the attic instead of outside, or a duct that has come off its boot and is blowing into the insulation.

Why it belongs in this job

It is the fastest way to soak an Kirkness attic from inside. We look for it while the space is open and flag it before covering anything, rather than blowing over the top.

How it works

Simple, clean, on schedule — Drywall in Edmonton

Free quote

We come out to your Edmonton property, take a real look at the drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every drywall quote in Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the drywall in Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Edmonton home while we finish the drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished drywall with us and you're happy with the result in Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the drywall contractor Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your drywall project in Edmonton.

Read our reviews on Google

FAQ — Loose Fill Insulation Kirkness Edmonton

Loose Fill Insulation Kirkness Edmonton: your questions answered

Do you seal before blowing?: Yes, and it is the step most often skipped. Loose material laid over an open ceiling penetration hides the leak rather than stopping it, and the warm moist air coming through is what wets the insulation from inside.
Is blown-in better than batts?: In an attic, usually yes, because it flows around trusses, bracing and wiring where batts get cut short or forced and leave gaps. In open framed walls at regular spacing, batts are fine. We recommend by the space, not by what is on the truck.
Can you just add over what is already up there?: Usually, and it is the best value if the existing material is dry, even and uncontaminated. If it is damp, matted, rodent-affected or hiding unsealed penetrations, adding over it buries the problem — we tell you which one we found.
What if you find old wiring?: If we find wiring that must not be covered, we stop and say so rather than blowing over it. That is an electrician's call, not ours, and it is a real reason a job gets paused rather than finished the same day.
Will it block my soffit vents?: Not if baffles go in first. Loose material can also be pushed around by wind at the eaves, so the baffles both hold it clear of the vents and stop the edge being scoured thin — which is exactly where the house loses heat.
Can you blow insulation into my walls without opening them?: Often yes — dense-pack through small holes, packed hard enough that it does not slump and leave a cold band at the top. The holes then need filling and finishing, which is drywall work, so we quote that with it rather than surprising you.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Loose Fill Insulation Kirkness Edmonton

Loose-fill insulation in Kirkness — settled depth is what you are buying