Will it make the house quieter?

It noticeably reduces airborne noise from outside — traffic, aircraft, neighbours. It does very little for footsteps from a floor above, which travel through structure, and we would rather say which half it fixes.

What if you find old wiring?

If we find wiring that must not be covered, we stop and say so rather than blowing over it. That is an electrician's call, not ours, and it is a real reason a job gets paused rather than finished the same day.

How is old insulation removed?

With a vacuum and hose into sealed bags, not shovels, because disturbing decades of settled material raises a lot of dust. It also gives a clean deck to air-seal and a look at the structure before it is covered again.

Do you seal before blowing?

Yes, and it is the step most often skipped. Loose material laid over an open ceiling penetration hides the leak rather than stopping it, and the warm moist air coming through is what wets the insulation from inside.

How do I know I got what I paid for?

Bag count. Every bag states the area it covers at a given depth, so bags used divided by area is exactly what went in. We keep them, mark the target settled depth, and read the depth back at the corners rather than the middle.

Does loose-fill settle?

Yes, which is why it is specified at a settled depth rather than how it looks on the day. A job blown to look right can measure short a year later. We work to the published settled figure and mark it before starting.

Loose Fill Insulation Kensington Edmonton | Blown-In

Blown-in insulation for Kensington attics and closed cavities

Loose-fill insulation is blown in rather than cut and fitted, which makes it the right answer wherever a batt cannot go: over an irregular Kensington attic floor, around trusses and bracing, and into wall cavities that are already closed. What you are paying for is settled depth spread evenly, and that is a thing which can be measured. Depth markers go in before the hose starts, and we read them at the corners rather than in the middle where it is always deepest.

Ceiling penetrations air-sealed first, not buried
Existing material assessed — topped up, or removed if it is wet or contaminated
Even coverage carried right out over the top plates
Settled depth specified and marked before the hose starts
Depth read back at the corners, not just where the hatch is
Baffles at the eaves so soffit venting stays clear

Pot lights buried in loose material

A heat question

Older recessed fixtures are not all rated to be covered, and loose-fill packs right against them.

What we check

Whether the Kensington fixtures are rated for insulation contact. Where they are not, they get a proper clearance detail rather than being buried and hoped about — and that detail is also a sealed one, so it does not become a new air leak.

Kensington drywall in context

About Kensington

Kensington was annexed to the City in 1913 during a real estate boom but most development didn't occur until the 1950s.

What we see in Kensington

In Kensington the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Topping up what is already there

Usually the best value

Dry, uncontaminated existing material does not need removing. Blowing over it to reach the target settled depth costs a fraction of a strip-and-replace.

When we say no

If it is damp, matted flat, rodent-affected, or hiding unsealed penetrations, adding over it buries a problem. We say which one we found in the Kensington attic and price both options.

Bath fans and the ducts above the ceiling

A very common find

Fans discharging into the attic instead of outside, or a duct that has come off its boot and is blowing into the insulation.

Why it belongs in this job

It is the fastest way to soak an Kensington attic from inside. We look for it while the space is open and flag it before covering anything, rather than blowing over the top.

Cellulose or fibreglass, and when it matters

Two common materials

Cellulose is recycled paper treated for fire and pests; loose-fill fibreglass is the same glass wool as a batt, chopped. Both work.

How we choose for an Kensington attic

Cellulose is denser, packs into odd shapes well and resists air movement through it better. Fibreglass is lighter, which matters on a ceiling of uncertain strength. Where the existing material is one of them, matching it is usually simpler than layering the other over top.

Settled depth versus installed depth

The number that counts

Loose-fill settles after installation. A job blown to look right on the day can be measurably short a year later.

How it is specified

The manufacturer publishes a settled depth and the bag count needed to reach it over a given area. We work to that and mark it, rather than blowing until the Kensington attic looks full.

Loose-fill or batts, decided on the space

Not a loyalty question

Batts suit open framing at regular spacing. Loose-fill suits irregular, obstructed or already-closed spaces.

How we quote it

We look at the Kensington space and recommend the one that fits it, including saying when a mix is right — batts in the open framed walls, blown-in above the ceiling. Nobody should be sold the material the truck happens to carry.

How it works

Simple, clean, on schedule — Drywall in Edmonton

Free quote

We come out to your Edmonton property, take a real look at the drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every drywall quote in Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the drywall in Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Edmonton home while we finish the drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished drywall with us and you're happy with the result in Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the drywall contractor Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your drywall project in Edmonton.

Read our reviews on Google

FAQ — Loose Fill Insulation Kensington Edmonton

Loose Fill Insulation Kensington Edmonton: your questions answered

Will it make the house quieter?: It noticeably reduces airborne noise from outside — traffic, aircraft, neighbours. It does very little for footsteps from a floor above, which travel through structure, and we would rather say which half it fixes.
What if you find old wiring?: If we find wiring that must not be covered, we stop and say so rather than blowing over it. That is an electrician's call, not ours, and it is a real reason a job gets paused rather than finished the same day.
How is old insulation removed?: With a vacuum and hose into sealed bags, not shovels, because disturbing decades of settled material raises a lot of dust. It also gives a clean deck to air-seal and a look at the structure before it is covered again.
Do you seal before blowing?: Yes, and it is the step most often skipped. Loose material laid over an open ceiling penetration hides the leak rather than stopping it, and the warm moist air coming through is what wets the insulation from inside.
How do I know I got what I paid for?: Bag count. Every bag states the area it covers at a given depth, so bags used divided by area is exactly what went in. We keep them, mark the target settled depth, and read the depth back at the corners rather than the middle.
Does loose-fill settle?: Yes, which is why it is specified at a settled depth rather than how it looks on the day. A job blown to look right can measure short a year later. We work to the published settled figure and mark it before starting.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Loose Fill Insulation Kensington Edmonton

Blown-in insulation for Kensington attics and closed cavities