Dusty — the machine sits outside and a hose runs through the house to the hatch. We protect the route, seal around the hatch and vacuum afterwards. What the house looks like at the end is most of the difference between crews.

Can you blow insulation into my walls without opening them?

Often yes — dense-pack through small holes, packed hard enough that it does not slump and leave a cold band at the top. The holes then need filling and finishing, which is drywall work, so we quote that with it rather than surprising you.

Can you just add over what is already up there?

Usually, and it is the best value if the existing material is dry, even and uncontaminated. If it is damp, matted, rodent-affected or hiding unsealed penetrations, adding over it buries the problem — we tell you which one we found.

Is it too heavy for my ceiling?

Rarely, but worth thinking about on an older lath ceiling or a long unsupported span. Where the ceiling is old or already sagging we would rather use the lighter material at a sensible depth, and sometimes recommend fixing the ceiling first.

Will it make the house quieter?

It noticeably reduces airborne noise from outside — traffic, aircraft, neighbours. It does very little for footsteps from a floor above, which travel through structure, and we would rather say which half it fixes.

What about my pot lights?

Older recessed fixtures are not all rated to be covered and loose-fill packs right against them. We check the rating, and where they are not rated they get a proper clearance detail that is also sealed, rather than being buried and hoped about.

Loose Fill Insulation Idylwylde | Loose Fill Insulation

Blown-in insulation for Idylwylde attics and closed cavities

Loose-fill insulation is blown in rather than cut and fitted, which makes it the right answer wherever a batt cannot go: over an irregular Idylwylde attic floor, around trusses and bracing, and into wall cavities that are already closed. What you are paying for is settled depth spread evenly, and that is a thing which can be measured. Depth markers go in before the hose starts, and we read them at the corners rather than in the middle where it is always deepest.

Even coverage carried right out over the top plates
Settled depth specified and marked before the hose starts
Ceiling penetrations air-sealed first, not buried
Baffles at the eaves so soffit venting stays clear
Existing material assessed — topped up, or removed if it is wet or contaminated
Depth read back at the corners, not just where the hatch is

Topping up what is already there

Usually the best value

Dry, uncontaminated existing material does not need removing. Blowing over it to reach the target settled depth costs a fraction of a strip-and-replace.

When we say no

If it is damp, matted flat, rodent-affected, or hiding unsealed penetrations, adding over it buries a problem. We say which one we found in the Idylwylde attic and price both options.

Idylwylde drywall in context

About Idylwylde

Idylwylde is bounded by four major roadways, which serve to keep the area's centre quiet.

What we see in Idylwylde

In Idylwylde the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Bag count is the honest check

Coverage is arithmetic

Every bag states the area it covers at a given depth. Bags used, divided by area, tells you exactly what was installed.

Why we keep them

Depth can be probed in a few spots and averaged; the bag count cannot be argued with. On an Idylwylde attic it is the simplest proof that what was quoted is what went in.

The material must not block the eaves

Loose material moves

Unlike a batt, blown-in can be pushed by wind washing at the eaves and drift away from where it was placed.

Baffles, every time

Baffles hold it back from the soffit vents and stop wind scouring the edge thin. In an Idylwylde attic that band above the exterior wall is exactly where the house loses heat, so it is the last place to accept a thin spot.

Moisture is what ruins it

Wet insulation is not insulation

Loose-fill that takes moisture packs down, loses most of its value and does not recover when it dries.

Finding the cause first

A damp patch in an Idylwylde attic means a roof leak, a bathroom fan venting into the space, or warm moist air leaking up through the ceiling. Blowing new material over any of those wastes it.

The hatch, again, because it undoes the rest

The one gap left

You can blow a perfect even depth across an Idylwylde ceiling and still lose heat through an uninsulated hatch that loose material spills through every time it opens.

What it needs

An insulated, weatherstripped cover and a dam around the opening high enough to hold the new depth back.

How it works

Simple, clean, on schedule — Drywall in Edmonton

Free quote

We come out to your Edmonton property, take a real look at the drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every drywall quote in Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the drywall in Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Edmonton home while we finish the drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished drywall with us and you're happy with the result in Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the drywall contractor Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your drywall project in Edmonton.

Read our reviews on Google

FAQ — Loose Fill Insulation Idylwylde

Loose Fill Insulation Idylwylde: your questions answered

How messy is it?: Dusty — the machine sits outside and a hose runs through the house to the hatch. We protect the route, seal around the hatch and vacuum afterwards. What the house looks like at the end is most of the difference between crews.
Can you blow insulation into my walls without opening them?: Often yes — dense-pack through small holes, packed hard enough that it does not slump and leave a cold band at the top. The holes then need filling and finishing, which is drywall work, so we quote that with it rather than surprising you.
Can you just add over what is already up there?: Usually, and it is the best value if the existing material is dry, even and uncontaminated. If it is damp, matted, rodent-affected or hiding unsealed penetrations, adding over it buries the problem — we tell you which one we found.
Is it too heavy for my ceiling?: Rarely, but worth thinking about on an older lath ceiling or a long unsupported span. Where the ceiling is old or already sagging we would rather use the lighter material at a sensible depth, and sometimes recommend fixing the ceiling first.
Will it make the house quieter?: It noticeably reduces airborne noise from outside — traffic, aircraft, neighbours. It does very little for footsteps from a floor above, which travel through structure, and we would rather say which half it fixes.
What about my pot lights?: Older recessed fixtures are not all rated to be covered and loose-fill packs right against them. We check the rating, and where they are not rated they get a proper clearance detail that is also sealed, rather than being buried and hoped about.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Loose Fill Insulation Idylwylde

Blown-in insulation for Idylwylde attics and closed cavities