How is old insulation removed?

With a vacuum and hose into sealed bags, not shovels, because disturbing decades of settled material raises a lot of dust. It also gives a clean deck to air-seal and a look at the structure before it is covered again.

Cellulose or fibreglass?

Both work. Cellulose is denser, packs into odd shapes and resists air movement through it better; fibreglass is lighter, which matters on a ceiling of uncertain strength. Where there is existing material, matching it is usually simpler than layering the other over it.

Can I still store things in the attic?

Only over a raised platform. Anything laid straight on the joists compresses the material and cuts a thin channel through the middle of the ceiling. Otherwise a fully insulated attic is not also a storage room.

Does loose-fill settle?

Yes, which is why it is specified at a settled depth rather than how it looks on the day. A job blown to look right can measure short a year later. We work to the published settled figure and mark it before starting.

Can you blow insulation into my walls without opening them?

Often yes — dense-pack through small holes, packed hard enough that it does not slump and leave a cold band at the top. The holes then need filling and finishing, which is drywall work, so we quote that with it rather than surprising you.

What about my pot lights?

Older recessed fixtures are not all rated to be covered and loose-fill packs right against them. We check the rating, and where they are not rated they get a proper clearance detail that is also sealed, rather than being buried and hoped about.

Loose Fill Insulation Charlesworth Edmonton | Blown-In

Loose-fill insulation in Charlesworth, measured rather than estimated

Blown-in material fills the awkward parts of an Charlesworth building that batts leave gapped — around cross-bracing, over the top plates of interior walls, into the shallow triangle at the eaves. It settles over time, which is why it is specified at a settled depth rather than the depth it looks on the day. Air sealing comes first, because loose material laid over an open ceiling penetration hides the leak instead of stopping it.

Ceiling penetrations air-sealed first, not buried
Settled depth specified and marked before the hose starts
Even coverage carried right out over the top plates
Depth read back at the corners, not just where the hatch is
Existing material assessed — topped up, or removed if it is wet or contaminated
Baffles at the eaves so soffit venting stays clear

Storage areas and the platform question

The trade-off is real

Anything laid on the joists compresses loose-fill and cuts a thin channel through the middle of an Charlesworth ceiling.

Doing it properly

If storage is genuinely needed, a raised platform over a limited area lets full depth continue underneath. Otherwise the honest answer is that a fully insulated attic is not also a storage room.

Working in a cathedral or a low attic

Not every space suits it

A vented sloped ceiling needs its air channel kept clear, and a shallow attic may not have room for the hose or the depth.

Being straight about it

Where an Charlesworth roof space cannot take a proper depth without blocking ventilation, we say what the space can actually achieve instead of quoting a number the geometry will not allow.

Bath fans and the ducts above the ceiling

A very common find

Fans discharging into the attic instead of outside, or a duct that has come off its boot and is blowing into the insulation.

Why it belongs in this job

It is the fastest way to soak an Charlesworth attic from inside. We look for it while the space is open and flag it before covering anything, rather than blowing over the top.

Access, hoses and how much of the house we cross

Practical reality

The machine sits outside and a hose runs to the Charlesworth attic hatch, which usually means through a hallway or a closet.

Keeping it clean

Protected route, sealed hatch surround, the space vacuumed after. It is a dusty trade and the difference between a good crew and a bad one is mostly what the house looks like at the end.

What it does for sound

A side benefit

A deep layer of loose-fill over an Charlesworth ceiling noticeably reduces airborne noise from outside — traffic, aircraft, neighbours.

Being clear about limits

It does very little for footsteps from a floor above, which travel through structure. If quieting the house is the real goal we would rather say which half this fixes.

The material must not block the eaves

Loose material moves

Unlike a batt, blown-in can be pushed by wind washing at the eaves and drift away from where it was placed.

Baffles, every time

Baffles hold it back from the soffit vents and stop wind scouring the edge thin. In an Charlesworth attic that band above the exterior wall is exactly where the house loses heat, so it is the last place to accept a thin spot.

How it works

Simple, clean, on schedule — Drywall in Edmonton

Free quote

We come out to your Edmonton property, take a real look at the drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every drywall quote in Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the drywall in Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Edmonton home while we finish the drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished drywall with us and you're happy with the result in Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the drywall contractor Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your drywall project in Edmonton.

Read our reviews on Google

FAQ — Loose Fill Insulation Charlesworth Edmonton

Loose Fill Insulation Charlesworth Edmonton: your questions answered

How is old insulation removed?: With a vacuum and hose into sealed bags, not shovels, because disturbing decades of settled material raises a lot of dust. It also gives a clean deck to air-seal and a look at the structure before it is covered again.
Cellulose or fibreglass?: Both work. Cellulose is denser, packs into odd shapes and resists air movement through it better; fibreglass is lighter, which matters on a ceiling of uncertain strength. Where there is existing material, matching it is usually simpler than layering the other over it.
Can I still store things in the attic?: Only over a raised platform. Anything laid straight on the joists compresses the material and cuts a thin channel through the middle of the ceiling. Otherwise a fully insulated attic is not also a storage room.
Does loose-fill settle?: Yes, which is why it is specified at a settled depth rather than how it looks on the day. A job blown to look right can measure short a year later. We work to the published settled figure and mark it before starting.
Can you blow insulation into my walls without opening them?: Often yes — dense-pack through small holes, packed hard enough that it does not slump and leave a cold band at the top. The holes then need filling and finishing, which is drywall work, so we quote that with it rather than surprising you.
What about my pot lights?: Older recessed fixtures are not all rated to be covered and loose-fill packs right against them. We check the rating, and where they are not rated they get a proper clearance detail that is also sealed, rather than being buried and hoped about.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Loose Fill Insulation Charlesworth Edmonton

Loose-fill insulation in Charlesworth, measured rather than estimated