What if you find old wiring?

If we find wiring that must not be covered, we stop and say so rather than blowing over it. That is an electrician's call, not ours, and it is a real reason a job gets paused rather than finished the same day.

How do I know I got what I paid for?

Bag count. Every bag states the area it covers at a given depth, so bags used divided by area is exactly what went in. We keep them, mark the target settled depth, and read the depth back at the corners rather than the middle.

Can you blow insulation into my walls without opening them?

Often yes — dense-pack through small holes, packed hard enough that it does not slump and leave a cold band at the top. The holes then need filling and finishing, which is drywall work, so we quote that with it rather than surprising you.

Cellulose or fibreglass?

Both work. Cellulose is denser, packs into odd shapes and resists air movement through it better; fibreglass is lighter, which matters on a ceiling of uncertain strength. Where there is existing material, matching it is usually simpler than layering the other over it.

What about my pot lights?

Older recessed fixtures are not all rated to be covered and loose-fill packs right against them. We check the rating, and where they are not rated they get a proper clearance detail that is also sealed, rather than being buried and hoped about.

Will it block my soffit vents?

Not if baffles go in first. Loose material can also be pushed around by wind at the eaves, so the baffles both hold it clear of the vents and stop the edge being scoured thin — which is exactly where the house loses heat.

Loose Fill Insulation Cameron Heights Edmonton | Blown-In

Loose-fill insulation in Cameron Heights — settled depth is what you are buying

Loose-fill insulation is blown in rather than cut and fitted, which makes it the right answer wherever a batt cannot go: over an irregular Cameron Heights attic floor, around trusses and bracing, and into wall cavities that are already closed. What you are paying for is settled depth spread evenly, and that is a thing which can be measured. Depth markers go in before the hose starts, and we read them at the corners rather than in the middle where it is always deepest.

Even coverage carried right out over the top plates
Depth read back at the corners, not just where the hatch is
Existing material assessed — topped up, or removed if it is wet or contaminated
Settled depth specified and marked before the hose starts
Ceiling penetrations air-sealed first, not buried
Baffles at the eaves so soffit venting stays clear

Cameron Heights drywall in context

About Cameron Heights

Cameron Heights was named after John Cameron, a pioneer and businessman who lived at the north end of the road that now bears his name (Cameron Avenue).

What we see in Cameron Heights

In Cameron Heights the drywall work is first-year settling, basement dev for first owners, Level 5 over builder-grade. We confirm what your home actually needs on site, in writing, before anything starts.

Loose-fill or batts, decided on the space

Not a loyalty question

Batts suit open framing at regular spacing. Loose-fill suits irregular, obstructed or already-closed spaces.

How we quote it

We look at the Cameron Heights space and recommend the one that fits it, including saying when a mix is right — batts in the open framed walls, blown-in above the ceiling. Nobody should be sold the material the truck happens to carry.

Removing old loose-fill

A vacuum job, not a shovel job

Old blown-in comes out with a vacuum and hose into sealed bags, because disturbing decades of settled material makes a great deal of airborne dust.

What it buys

A clean deck to air-seal properly and, in older Cameron Heights homes, the chance to see the ceiling structure and any past leaks before they are covered again.

Storage areas and the platform question

The trade-off is real

Anything laid on the joists compresses loose-fill and cuts a thin channel through the middle of an Cameron Heights ceiling.

Doing it properly

If storage is genuinely needed, a raised platform over a limited area lets full depth continue underneath. Otherwise the honest answer is that a fully insulated attic is not also a storage room.

Bag count is the honest check

Coverage is arithmetic

Every bag states the area it covers at a given depth. Bags used, divided by area, tells you exactly what was installed.

Why we keep them

Depth can be probed in a few spots and averaged; the bag count cannot be argued with. On an Cameron Heights attic it is the simplest proof that what was quoted is what went in.

Filling around bracing and trusses

Why batts fail here

Truss webs, cross-bracing and wiring turn an Cameron Heights attic floor into a shape no rectangle fits. Batts get cut short or forced, leaving gaps.

What blown-in does

It flows around all of it and fills to a consistent depth. This is the single clearest reason to choose loose-fill over batts above a ceiling.

How it works

Simple, clean, on schedule — Drywall in Edmonton

Free quote

We come out to your Edmonton property, take a real look at the drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every drywall quote in Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the drywall in Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Edmonton home while we finish the drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished drywall with us and you're happy with the result in Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the drywall contractor Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your drywall project in Edmonton.

Read our reviews on Google

FAQ — Loose Fill Insulation Cameron Heights Edmonton

Loose Fill Insulation Cameron Heights Edmonton: your questions answered

What if you find old wiring?: If we find wiring that must not be covered, we stop and say so rather than blowing over it. That is an electrician's call, not ours, and it is a real reason a job gets paused rather than finished the same day.
How do I know I got what I paid for?: Bag count. Every bag states the area it covers at a given depth, so bags used divided by area is exactly what went in. We keep them, mark the target settled depth, and read the depth back at the corners rather than the middle.
Can you blow insulation into my walls without opening them?: Often yes — dense-pack through small holes, packed hard enough that it does not slump and leave a cold band at the top. The holes then need filling and finishing, which is drywall work, so we quote that with it rather than surprising you.
Cellulose or fibreglass?: Both work. Cellulose is denser, packs into odd shapes and resists air movement through it better; fibreglass is lighter, which matters on a ceiling of uncertain strength. Where there is existing material, matching it is usually simpler than layering the other over it.
What about my pot lights?: Older recessed fixtures are not all rated to be covered and loose-fill packs right against them. We check the rating, and where they are not rated they get a proper clearance detail that is also sealed, rather than being buried and hoped about.
Will it block my soffit vents?: Not if baffles go in first. Loose material can also be pushed around by wind at the eaves, so the baffles both hold it clear of the vents and stop the edge being scoured thin — which is exactly where the house loses heat.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Loose Fill Insulation Cameron Heights Edmonton

Loose-fill insulation in Cameron Heights — settled depth is what you are buying