Will it block my soffit vents?

Not if baffles go in first. Loose material can also be pushed around by wind at the eaves, so the baffles both hold it clear of the vents and stop the edge being scoured thin — which is exactly where the house loses heat.

Is it too heavy for my ceiling?

Rarely, but worth thinking about on an older lath ceiling or a long unsupported span. Where the ceiling is old or already sagging we would rather use the lighter material at a sensible depth, and sometimes recommend fixing the ceiling first.

Does loose-fill settle?

Yes, which is why it is specified at a settled depth rather than how it looks on the day. A job blown to look right can measure short a year later. We work to the published settled figure and mark it before starting.

Cellulose or fibreglass?

Both work. Cellulose is denser, packs into odd shapes and resists air movement through it better; fibreglass is lighter, which matters on a ceiling of uncertain strength. Where there is existing material, matching it is usually simpler than layering the other over it.

What if you find old wiring?

If we find wiring that must not be covered, we stop and say so rather than blowing over it. That is an electrician's call, not ours, and it is a real reason a job gets paused rather than finished the same day.

Do you seal before blowing?

Yes, and it is the step most often skipped. Loose material laid over an open ceiling penetration hides the leak rather than stopping it, and the warm moist air coming through is what wets the insulation from inside.

Loose Fill Insulation Belvedere | Loose Fill Insulation

Loose-fill insulation in Belvedere — settled depth is what you are buying

Loose-fill insulation is blown in rather than cut and fitted, which makes it the right answer wherever a batt cannot go: over an irregular Belvedere attic floor, around trusses and bracing, and into wall cavities that are already closed. What you are paying for is settled depth spread evenly, and that is a thing which can be measured. Depth markers go in before the hose starts, and we read them at the corners rather than in the middle where it is always deepest.

Even coverage carried right out over the top plates
Baffles at the eaves so soffit venting stays clear
Ceiling penetrations air-sealed first, not buried
Existing material assessed — topped up, or removed if it is wet or contaminated
Depth read back at the corners, not just where the hatch is
Settled depth specified and marked before the hose starts

Weight on the ceiling below

Worth a thought

Insulation is light, but a deep layer of dense material over a large Belvedere ceiling is still a load, particularly on an older lath ceiling or a long unsupported span.

How we handle it

Where the ceiling is old or already sagging, the lighter material and a sensible depth beat the deepest possible number. Fixing the ceiling first is sometimes the honest recommendation.

Belvedere drywall in context

About Belvedere

Once part of the village of North Edmonton, Belvedere contains the Fort Road, which first thrived at a time when the trek between Fort Saskatchewan and Edmonton was made by wagon.

What we see in Belvedere

In Belvedere the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Blowing into a wall that is already closed

Dense-pack

Loose-fill can be blown into closed Belvedere wall cavities through small holes, packed to a density that stops it slumping and leaving a cold band at the top.

Where it fits

It suits an older home you do not want to open up. It needs the holes made, filled and finished afterwards, which is drywall work — so quote the patching with it rather than discovering it later.

Removing old loose-fill

A vacuum job, not a shovel job

Old blown-in comes out with a vacuum and hose into sealed bags, because disturbing decades of settled material makes a great deal of airborne dust.

What it buys

A clean deck to air-seal properly and, in older Belvedere homes, the chance to see the ceiling structure and any past leaks before they are covered again.

Storage areas and the platform question

The trade-off is real

Anything laid on the joists compresses loose-fill and cuts a thin channel through the middle of an Belvedere ceiling.

Doing it properly

If storage is genuinely needed, a raised platform over a limited area lets full depth continue underneath. Otherwise the honest answer is that a fully insulated attic is not also a storage room.

Working in a cathedral or a low attic

Not every space suits it

A vented sloped ceiling needs its air channel kept clear, and a shallow attic may not have room for the hose or the depth.

Being straight about it

Where an Belvedere roof space cannot take a proper depth without blocking ventilation, we say what the space can actually achieve instead of quoting a number the geometry will not allow.

Access, hoses and how much of the house we cross

Practical reality

The machine sits outside and a hose runs to the Belvedere attic hatch, which usually means through a hallway or a closet.

Keeping it clean

Protected route, sealed hatch surround, the space vacuumed after. It is a dusty trade and the difference between a good crew and a bad one is mostly what the house looks like at the end.

How it works

Simple, clean, on schedule — Drywall in Edmonton

Free quote

We come out to your Edmonton property, take a real look at the drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every drywall quote in Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the drywall in Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Edmonton home while we finish the drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished drywall with us and you're happy with the result in Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the drywall contractor Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your drywall project in Edmonton.

Read our reviews on Google

FAQ — Loose Fill Insulation Belvedere

Loose Fill Insulation Belvedere: your questions answered

Will it block my soffit vents?: Not if baffles go in first. Loose material can also be pushed around by wind at the eaves, so the baffles both hold it clear of the vents and stop the edge being scoured thin — which is exactly where the house loses heat.
Is it too heavy for my ceiling?: Rarely, but worth thinking about on an older lath ceiling or a long unsupported span. Where the ceiling is old or already sagging we would rather use the lighter material at a sensible depth, and sometimes recommend fixing the ceiling first.
Does loose-fill settle?: Yes, which is why it is specified at a settled depth rather than how it looks on the day. A job blown to look right can measure short a year later. We work to the published settled figure and mark it before starting.
Cellulose or fibreglass?: Both work. Cellulose is denser, packs into odd shapes and resists air movement through it better; fibreglass is lighter, which matters on a ceiling of uncertain strength. Where there is existing material, matching it is usually simpler than layering the other over it.
What if you find old wiring?: If we find wiring that must not be covered, we stop and say so rather than blowing over it. That is an electrician's call, not ours, and it is a real reason a job gets paused rather than finished the same day.
Do you seal before blowing?: Yes, and it is the step most often skipped. Loose material laid over an open ceiling penetration hides the leak rather than stopping it, and the warm moist air coming through is what wets the insulation from inside.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Loose Fill Insulation Belvedere

Loose-fill insulation in Belvedere — settled depth is what you are buying