Will it block my soffit vents?

Not if baffles go in first. Loose material can also be pushed around by wind at the eaves, so the baffles both hold it clear of the vents and stop the edge being scoured thin — which is exactly where the house loses heat.

Can you blow insulation into my walls without opening them?

Often yes — dense-pack through small holes, packed hard enough that it does not slump and leave a cold band at the top. The holes then need filling and finishing, which is drywall work, so we quote that with it rather than surprising you.

What if you find old wiring?

If we find wiring that must not be covered, we stop and say so rather than blowing over it. That is an electrician's call, not ours, and it is a real reason a job gets paused rather than finished the same day.

Does loose-fill settle?

Yes, which is why it is specified at a settled depth rather than how it looks on the day. A job blown to look right can measure short a year later. We work to the published settled figure and mark it before starting.

How is old insulation removed?

With a vacuum and hose into sealed bags, not shovels, because disturbing decades of settled material raises a lot of dust. It also gives a clean deck to air-seal and a look at the structure before it is covered again.

What do I get when the job is done?

The bag count, the target settled depth, and photographs of the finished space including the corners and the eaves — so you can confirm years later what was actually installed instead of probing a hole and guessing.

Loose Fill Insulation Allard Edmonton | Blown-In

Loose-fill insulation in Allard — settled depth is what you are buying

Loose-fill insulation is blown in rather than cut and fitted, which makes it the right answer wherever a batt cannot go: over an irregular Allard attic floor, around trusses and bracing, and into wall cavities that are already closed. What you are paying for is settled depth spread evenly, and that is a thing which can be measured. Depth markers go in before the hose starts, and we read them at the corners rather than in the middle where it is always deepest.

Baffles at the eaves so soffit venting stays clear
Settled depth specified and marked before the hose starts
Depth read back at the corners, not just where the hatch is
Ceiling penetrations air-sealed first, not buried
Even coverage carried right out over the top plates
Existing material assessed — topped up, or removed if it is wet or contaminated

Storage areas and the platform question

The trade-off is real

Anything laid on the joists compresses loose-fill and cuts a thin channel through the middle of an Allard ceiling.

Doing it properly

If storage is genuinely needed, a raised platform over a limited area lets full depth continue underneath. Otherwise the honest answer is that a fully insulated attic is not also a storage room.

Removing old loose-fill

A vacuum job, not a shovel job

Old blown-in comes out with a vacuum and hose into sealed bags, because disturbing decades of settled material makes a great deal of airborne dust.

What it buys

A clean deck to air-seal properly and, in older Allard homes, the chance to see the ceiling structure and any past leaks before they are covered again.

The hatch, again, because it undoes the rest

The one gap left

You can blow a perfect even depth across an Allard ceiling and still lose heat through an uninsulated hatch that loose material spills through every time it opens.

What it needs

An insulated, weatherstripped cover and a dam around the opening high enough to hold the new depth back.

The material must not block the eaves

Loose material moves

Unlike a batt, blown-in can be pushed by wind washing at the eaves and drift away from where it was placed.

Baffles, every time

Baffles hold it back from the soffit vents and stop wind scouring the edge thin. In an Allard attic that band above the exterior wall is exactly where the house loses heat, so it is the last place to accept a thin spot.

Working in a cathedral or a low attic

Not every space suits it

A vented sloped ceiling needs its air channel kept clear, and a shallow attic may not have room for the hose or the depth.

Being straight about it

Where an Allard roof space cannot take a proper depth without blocking ventilation, we say what the space can actually achieve instead of quoting a number the geometry will not allow.

What it does for sound

A side benefit

A deep layer of loose-fill over an Allard ceiling noticeably reduces airborne noise from outside — traffic, aircraft, neighbours.

Being clear about limits

It does very little for footsteps from a floor above, which travel through structure. If quieting the house is the real goal we would rather say which half this fixes.

How it works

Simple, clean, on schedule — Drywall in Edmonton

Free quote

We come out to your Edmonton property, take a real look at the drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every drywall quote in Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the drywall in Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Edmonton home while we finish the drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished drywall with us and you're happy with the result in Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the drywall contractor Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your drywall project in Edmonton.

Read our reviews on Google

FAQ — Loose Fill Insulation Allard Edmonton

Loose Fill Insulation Allard Edmonton: your questions answered

Will it block my soffit vents?: Not if baffles go in first. Loose material can also be pushed around by wind at the eaves, so the baffles both hold it clear of the vents and stop the edge being scoured thin — which is exactly where the house loses heat.
Can you blow insulation into my walls without opening them?: Often yes — dense-pack through small holes, packed hard enough that it does not slump and leave a cold band at the top. The holes then need filling and finishing, which is drywall work, so we quote that with it rather than surprising you.
What if you find old wiring?: If we find wiring that must not be covered, we stop and say so rather than blowing over it. That is an electrician's call, not ours, and it is a real reason a job gets paused rather than finished the same day.
Does loose-fill settle?: Yes, which is why it is specified at a settled depth rather than how it looks on the day. A job blown to look right can measure short a year later. We work to the published settled figure and mark it before starting.
How is old insulation removed?: With a vacuum and hose into sealed bags, not shovels, because disturbing decades of settled material raises a lot of dust. It also gives a clean deck to air-seal and a look at the structure before it is covered again.
What do I get when the job is done?: The bag count, the target settled depth, and photographs of the finished space including the corners and the eaves — so you can confirm years later what was actually installed instead of probing a hole and guessing.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Insulation

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Loose Fill Insulation Allard Edmonton

Loose-fill insulation in Allard — settled depth is what you are buying