Where is fire-rated drywall required?

The standard Westwood fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Westwood project needs.

Do you handle the firestopping as well as the board?

We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.

Will it pass inspection in Westwood?

Yes — we install the correct Type X assembly and seal penetrations to spec so your Westwood separation passes inspection.

Does the rated wall have to go above the ceiling?

Yes. A separation that stops at a suspended ceiling is not a separation — fire and smoke go over it. The wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions.

Is Type X the same as fireproof?

No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.

Can I use 1/2 inch board if that is what is on site?

Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

Fire-Rated Drywall Westwood Edmonton | Type X Board

Fire-rated drywall in Westwood, installed to code

No shortcuts on Westwood fire-rating — separations, suites and party walls need code Type X rated assemblies to clear inspection and keep people safe. In Westwood we install fire-rated drywall to code and finish it clean. Westwood is one of North Central's newer communities, where fresh installation and first-year settling work are common, so fire-rated work here is common on garages and suites. We cover Westwood, Abbottsfield, Alberta Avenue, Beacon Heights and North Central, 7 days a week.

Party walls between units
Type X board to the assembly on the drawings
Garage ceilings and garage-to-house separations in Westwood
Furnace and mechanical room enclosures
Type X fire-rated board to code in Westwood
Party walls and legal-suite separations
Garage-to-house firewall separations

Common fire-rated situations in Westwood

In Westwood, westwood sits in Edmonton's North Central district. The character of Westwood has changed considerably in the second half of the 20th century. Across roughly 1,660 homes here, the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We cover Westwood and the surrounding North Central district, 7 days a week. Same trusted team, same process on every job — on-site quote, fixed price, no surprises.

Westwood drywall in context

About Westwood

The character of Westwood has changed considerably in the second half of the 20th century.

What we see in Westwood

In Westwood the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

What affects the cost of fire-rated drywall in Westwood?

Area and assembly

The cost in Westwood depends on the area and the rated assembly required — a single-layer garage ceiling is different from a two-layer party wall. The Westwood rating drives the build-up, and Type X board carries a premium over standard. We price off the spec and a site look.

Passing inspection in Westwood

The common rated jobs here are garages and suites. The rating only holds if the assembly is built and sealed exactly to spec, so we install it to code and seal penetrations properly so your Westwood project passes the first time.

Board thickness and why 5/8 is standard here

Not just thicker

Type X is 5/8 inch because the core needs that mass and the glass-fibre reinforcement to hold together as the gypsum calcines under heat.

The common error

Using 1/2 inch board in a rated Westwood assembly because it is what was on site. It looks identical once finished and it is not the tested assembly. Board arriving on site is checked against the specification rather than assumed.

Our Westwood fire-rated drywall process, step by step

Right board, right build-up

In Westwood we confirm the required rating, then install the correct Type X board in the right layers — the assembly, not just the board, is what carries the rating.

Seal and finish

Penetrations and edges are where a rated assembly fails, so we firestop and seal them, then tape and finish the board clean. An Westwood separation the inspector approves and the eye approves too.

Coordinating with the electrician early

Boxes in rated walls

Outlet and switch boxes in a rated Westwood assembly need treatment — spacing rules, pads or listed boxes — and back-to-back boxes are a particular problem.

Why early matters

Rearranging a box after board is up means opening a rated wall. Walking the wall with the electrician before boarding takes ten minutes and avoids that entirely.

Rated ceilings and the membrane above

Protecting the structure

A rated ceiling under living space is protecting the floor structure above it, which is why the board and its fastening are specified rather than optional.

Access hatches

Any hatch through it interrupts the assembly and needs a rated detail. It is a common find in Westwood garages where storage access was cut in afterwards and never addressed.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Westwood Edmonton

Free quote

We come out to your Westwood Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Westwood Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Westwood Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Westwood Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Westwood Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Westwood Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Westwood Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Westwood Edmonton

Fire-Rated Drywall Westwood Edmonton: your questions answered

Where is fire-rated drywall required?: The standard Westwood fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Westwood project needs.
Do you handle the firestopping as well as the board?: We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.
Will it pass inspection in Westwood?: Yes — we install the correct Type X assembly and seal penetrations to spec so your Westwood separation passes inspection.
Does the rated wall have to go above the ceiling?: Yes. A separation that stops at a suspended ceiling is not a separation — fire and smoke go over it. The wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions.
Is Type X the same as fireproof?: No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.
Can I use 1/2 inch board if that is what is on site?: Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Westwood Edmonton

Fire-rated drywall in Westwood, installed to code