Can you finish the fire-rated board too?

Yes — your Westridge separation passes code and looks properly finished, ready for paint.

Will it pass inspection in Westridge?

Yes — we install the correct Type X assembly and seal penetrations to spec so your Westridge separation passes inspection.

My Westridge garage ceiling has board but the joints are open. Is that a problem?

Usually yes. Untaped joints are one of the most common reasons a garage separation is not complete, because the board looks installed. Often the fix is finishing the joints and sealing penetrations rather than replacing the ceiling.

Is Type X the same as fireproof?

No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.

Do you stand behind your fire-rated work in Westridge?

Yes. We install to code and walk the Westridge job with you, and if something is not right we come back and make it right.

Where is fire-rated drywall required?

The standard Westridge fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Westridge project needs.

Fire-Rated Drywall Westridge Edmonton | Type X Board

Fire-rated drywall in Westridge, built as a complete assembly

In Westridge the code decides: garage separations, basement suites and party walls must carry Type X board in a rated assembly to pass inspection and protect the home. In Westridge we install fire-rated drywall to code and finish it clean. Westridge is this established West Edmonton community where reno, repair and ceiling drywall are common, so fire-rated work here is common on garages and suites. We cover Westridge, Aldergrove, Belmead, Callingwood North and West Edmonton, 7 days a week.

Type X fire-rated board to code in Westridge
Rated assemblies installed and sealed correctly
Finished clean and inspection-ready
Penetrations firestopped before the finish goes on
Westridge coverage — we come to you
Party walls between units
Basement legal-suite fire separations

Board thickness and why 5/8 is standard here

Not just thicker

Type X is 5/8 inch because the core needs that mass and the glass-fibre reinforcement to hold together as the gypsum calcines under heat.

The common error

Using 1/2 inch board in a rated Westridge assembly because it is what was on site. It looks identical once finished and it is not the tested assembly. Board arriving on site is checked against the specification rather than assumed.

Westridge drywall in context

About Westridge

Westridge is a long narrow neighbourhood extending into the North Saskatchewan River Valley.

What we see in Westridge

In Westridge the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

What makes drywall fire-rated in Westridge

The board is only part of it

Type X board carries a glass-fibre reinforced core that holds together longer under heat. That is what earns the rating in a lab, but only inside a tested assembly: a stated board thickness, stud spacing, screw pattern and joint treatment.

Why that matters on your job

Putting Type X on a wall does not make the wall rated. In Westridge we build the assembly the drawings specify, because an inspector is checking the system, not the sticker on the board.

Fire-rated garages, suites and party walls in Westridge

Garage firewalls

The most common fire-rated job in Westridge is the garage-to-house separation — Type X board on the common wall and ceiling. Code-compliant install and finish.

Legal suites and shared walls

Frequent work in Westridge homes and multi-unit buildings. We build the rated separations these require. See our legal suite drywall page.

Where Westridge homes usually need rated board

The four common places

Most rated drywall in Westridge houses is one of: the garage ceiling where living space sits above it, the garage-to-house wall, the furnace or mechanical room, and a legal-suite separation between dwelling units.

Renovations trigger it too

Finishing a basement, adding a suite or converting a garage often brings a separation into play that was not there before. If you are not sure whether your Westridge project triggers one, that is a question for the building official at permit stage, and we will tell you when we think you should ask.

Fire-rated drywall in a Westridge garage ceiling

The most common one we do

Where Westridge living space sits over a garage, the ceiling normally needs a rated separation. It is also the assembly most often found incomplete on older homes and DIY conversions — board up, joints untaped, pot lights cut straight through.

What we check before quoting

We look at what is above the ceiling, what is already installed, and whether the existing board is actually rated. Sometimes the honest answer is that the existing ceiling only needs its joints completed and its penetrations sealed rather than replacing.

Our Westridge fire-rated drywall process, step by step

Right board, right build-up

In Westridge we confirm the required rating, then install the correct Type X board in the right layers — the assembly, not just the board, is what carries the rating.

Seal and finish

Penetrations and edges are where a rated assembly fails, so we firestop and seal them, then tape and finish the board clean. An Westridge separation the inspector approves and the eye approves too.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Westridge Edmonton

Free quote

We come out to your Westridge Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Westridge Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Westridge Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Westridge Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Westridge Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Westridge Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Westridge Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Westridge Edmonton

Fire-Rated Drywall Westridge Edmonton: your questions answered

Can you finish the fire-rated board too?: Yes — your Westridge separation passes code and looks properly finished, ready for paint.
Will it pass inspection in Westridge?: Yes — we install the correct Type X assembly and seal penetrations to spec so your Westridge separation passes inspection.
My Westridge garage ceiling has board but the joints are open. Is that a problem?: Usually yes. Untaped joints are one of the most common reasons a garage separation is not complete, because the board looks installed. Often the fix is finishing the joints and sealing penetrations rather than replacing the ceiling.
Is Type X the same as fireproof?: No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.
Do you stand behind your fire-rated work in Westridge?: Yes. We install to code and walk the Westridge job with you, and if something is not right we come back and make it right.
Where is fire-rated drywall required?: The standard Westridge fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Westridge project needs.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Westridge Edmonton

Fire-rated drywall in Westridge, built as a complete assembly