Do you install fire-rated drywall in Wellington?

Yes — fire-rated drywall in Wellington is part of our regular work, and we are usually booked within the week. We also cover Albany, Athlone, Baranow and Northwest.

Will it pass inspection in Wellington?

Yes — we install the correct Type X assembly and seal penetrations to spec so your Wellington separation passes inspection.

Where is fire-rated drywall required?

The standard Wellington fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Wellington project needs.

How do I know which rated assembly my Wellington project needs?

It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.

Can I use 1/2 inch board if that is what is on site?

Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

Does the rated wall have to go above the ceiling?

Yes. A separation that stops at a suspended ceiling is not a separation — fire and smoke go over it. The wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions.

Fire-Rated Drywall Wellington Edmonton | Type X Board

Fire-rated drywall in Wellington, installed to code

No shortcuts on Wellington fire-rating — separations, suites and party walls need code Type X rated assemblies to clear inspection and keep people safe. In Wellington we install fire-rated drywall to code and finish it clean. Wellington is one of Northwest's newer communities, where fresh installation and first-year settling work are common, so fire-rated work here is common on garages and suites. We cover Wellington, Albany, Athlone, Baranow and Northwest, 7 days a week.

Basement legal-suite fire separations
Party walls between units
Garage-to-house firewall separations
Type X fire-rated board to code in Wellington
Furnace and mechanical room enclosures
Wellington coverage — we come to you
Garage ceilings and garage-to-house separations in Wellington

Fire-rated drywall in a Wellington garage ceiling

The most common one we do

Where Wellington living space sits over a garage, the ceiling normally needs a rated separation. It is also the assembly most often found incomplete on older homes and DIY conversions — board up, joints untaped, pot lights cut straight through.

What we check before quoting

We look at what is above the ceiling, what is already installed, and whether the existing board is actually rated. Sometimes the honest answer is that the existing ceiling only needs its joints completed and its penetrations sealed rather than replacing.

What makes drywall fire-rated in Wellington

The board is only part of it

Type X board carries a glass-fibre reinforced core that holds together longer under heat. That is what earns the rating in a lab, but only inside a tested assembly: a stated board thickness, stud spacing, screw pattern and joint treatment.

Why that matters on your job

Putting Type X on a wall does not make the wall rated. In Wellington we build the assembly the drawings specify, because an inspector is checking the system, not the sticker on the board.

What happens when an assembly is altered later

Every future trade is a risk

A rated Wellington wall or ceiling stays rated only while nobody cuts an unsealed hole in it. Later work — a fan, a light, a duct, a speaker — can quietly undo it.

What we leave you

We photograph the rated work before covering it, so there is a record of what is behind the finish for whoever works on the house next.

Rated ceilings and the membrane above

Protecting the structure

A rated ceiling under living space is protecting the floor structure above it, which is why the board and its fastening are specified rather than optional.

Access hatches

Any hatch through it interrupts the assembly and needs a rated detail. It is a common find in Wellington garages where storage access was cut in afterwards and never addressed.

Joints, screws and the details inspectors actually check

The parts nobody photographs

A rated assembly in Wellington depends on screw spacing, joints landing on framing, and joints being taped and filled. Loose screw spacing, unsupported butt joints and untaped joints are the usual reasons a rated wall does not pass.

Two-layer assemblies

Where the assembly is two layers, the second layer joints are offset from the first so no joint runs straight through the wall. That offset is part of the rating, not a finishing preference.

Inspection, and what we hand over

Sequencing with your inspection

Rated assemblies in Wellington are usually inspected before the finish covers them, so we sequence boarding and firestopping to suit your inspection date rather than working ahead and covering something the inspector needs to see.

If something fails

If an assembly does not pass, we want to hear the inspector reason directly. Most failures are specific and fixable — a screw pattern, an untaped joint, an unsealed penetration — and are corrected faster from the actual note than from a second-hand summary.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Wellington Edmonton

Free quote

We come out to your Wellington Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Wellington Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Wellington Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Wellington Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Wellington Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Wellington Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Wellington Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Wellington Edmonton

Fire-Rated Drywall Wellington Edmonton: your questions answered

Do you install fire-rated drywall in Wellington?: Yes — fire-rated drywall in Wellington is part of our regular work, and we are usually booked within the week. We also cover Albany, Athlone, Baranow and Northwest.
Will it pass inspection in Wellington?: Yes — we install the correct Type X assembly and seal penetrations to spec so your Wellington separation passes inspection.
Where is fire-rated drywall required?: The standard Wellington fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Wellington project needs.
How do I know which rated assembly my Wellington project needs?: It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.
Can I use 1/2 inch board if that is what is on site?: Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.
Does the rated wall have to go above the ceiling?: Yes. A separation that stops at a suspended ceiling is not a separation — fire and smoke go over it. The wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Wellington Edmonton

Fire-rated drywall in Wellington, installed to code