What if someone cuts into it later?

That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.

Can I put an access hatch in my rated garage ceiling?

Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Tawa garages where storage access was cut in afterwards and never addressed.

Do you handle the firestopping as well as the board?

We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.

Can you finish the fire-rated board too?

Yes — your Tawa separation passes code and looks properly finished, ready for paint.

Where is fire-rated drywall required?

The standard Tawa fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Tawa project needs.

Do you install fire-rated drywall in Tawa?

Yes — fire-rated drywall in Tawa is part of our regular work, and we are usually booked within the week. We also cover Bisset, Crawford Plains, Daly Grove and Mill Woods and Meadows.

Fire-Rated Drywall Tawa Edmonton | Type X Board

Type X board in Tawa for garages, suites and mechanical rooms

In Tawa the code decides: garage separations, basement suites and party walls must carry Type X board in a rated assembly to pass inspection and protect the home. In Tawa we install fire-rated drywall to code and finish it clean. Tawa is this established Mill Woods and Meadows community where reno, repair and ceiling drywall are common, so fire-rated work here is common on garages and suites. We cover Tawa, Bisset, Crawford Plains, Daly Grove and Mill Woods and Meadows, 7 days a week.

Joints taped as part of the rated assembly, not just for looks
Furnace and mechanical room enclosures
Party walls and legal-suite separations
Basement legal-suite fire separations
Finished clean and inspection-ready
Rated assemblies installed and sealed correctly
Type X board to the assembly on the drawings

Finishing a rated wall in Tawa without compromising it

Rated first, pretty second

Taping on a rated assembly in Tawa does two jobs: it completes the fire separation and it produces the surface you will paint. The tape and fill on the rated joints is not optional cosmetic work.

Level of finish

Beyond the rated joint treatment, the visible finish level is your choice — a garage ceiling rarely needs the same finish as a living room. We will tell you where a higher level is worth paying for and where it is not.

Tawa drywall in context

About Tawa

Tawa means "you are welcome" in the Cree language to honour Aboriginal leaders and history.

What we see in Tawa

In Tawa the drywall work is popcorn and stipple ceiling removal, settling+truss-uplift cracks, nail pops, Poly-B repipe patching repipe patching. We confirm what your home actually needs on site, in writing, before anything starts.

Coordinating with the electrician early

Boxes in rated walls

Outlet and switch boxes in a rated Tawa assembly need treatment — spacing rules, pads or listed boxes — and back-to-back boxes are a particular problem.

Why early matters

Rearranging a box after board is up means opening a rated wall. Walking the wall with the electrician before boarding takes ten minutes and avoids that entirely.

Type X and Type C are not interchangeable

Two different boards

Type X is the common 5/8 inch rated board. Type C carries additional additives that resist shrinkage at high heat and is specified where an assembly — often a ceiling — depends on the board staying in place longer.

Substituting downward fails

Where drawings call for Type C, Type X is not an equivalent, and an inspector who spots it will fail the assembly. We order to the specification on your Tawa drawings and tell you if what is on site does not match it.

Our Tawa fire-rated drywall process, step by step

Right board, right build-up

In Tawa we confirm the required rating, then install the correct Type X board in the right layers — the assembly, not just the board, is what carries the rating.

Seal and finish

Penetrations and edges are where a rated assembly fails, so we firestop and seal them, then tape and finish the board clean. An Tawa separation the inspector approves and the eye approves too.

Board thickness and why 5/8 is standard here

Not just thicker

Type X is 5/8 inch because the core needs that mass and the glass-fibre reinforcement to hold together as the gypsum calcines under heat.

The common error

Using 1/2 inch board in a rated Tawa assembly because it is what was on site. It looks identical once finished and it is not the tested assembly. Board arriving on site is checked against the specification rather than assumed.

Joints, screws and the details inspectors actually check

The parts nobody photographs

A rated assembly in Tawa depends on screw spacing, joints landing on framing, and joints being taped and filled. Loose screw spacing, unsupported butt joints and untaped joints are the usual reasons a rated wall does not pass.

Two-layer assemblies

Where the assembly is two layers, the second layer joints are offset from the first so no joint runs straight through the wall. That offset is part of the rating, not a finishing preference.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Tawa Edmonton

Free quote

We come out to your Tawa Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Tawa Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Tawa Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Tawa Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Tawa Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Tawa Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Tawa Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Tawa Edmonton

Fire-Rated Drywall Tawa Edmonton: your questions answered

What if someone cuts into it later?: That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.
Can I put an access hatch in my rated garage ceiling?: Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Tawa garages where storage access was cut in afterwards and never addressed.
Do you handle the firestopping as well as the board?: We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.
Can you finish the fire-rated board too?: Yes — your Tawa separation passes code and looks properly finished, ready for paint.
Where is fire-rated drywall required?: The standard Tawa fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Tawa project needs.
Do you install fire-rated drywall in Tawa?: Yes — fire-rated drywall in Tawa is part of our regular work, and we are usually booked within the week. We also cover Bisset, Crawford Plains, Daly Grove and Mill Woods and Meadows.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Tawa Edmonton

Type X board in Tawa for garages, suites and mechanical rooms