Can pot lights go in a rated ceiling?

Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Summerlea ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.

Can you finish the fire-rated board too?

Yes — your Summerlea separation passes code and looks properly finished, ready for paint.

Do you handle the firestopping as well as the board?

We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.

How do I know which rated assembly my Summerlea project needs?

It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.

Will it pass inspection in Summerlea?

Yes — we install the correct Type X assembly and seal penetrations to spec so your Summerlea separation passes inspection.

Is Type X the same as fireproof?

No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.

Fire-Rated Drywall Summerlea Edmonton | Type X Board

Type X board in Summerlea for garages, suites and mechanical rooms

In Summerlea the code decides: garage separations, basement suites and party walls must carry Type X board in a rated assembly to pass inspection and protect the home. In Summerlea we install fire-rated drywall to code and finish it clean. Summerlea is this established West Edmonton community where reno, repair and ceiling drywall are common, so fire-rated work here is common on garages and suites. We cover Summerlea, Aldergrove, Belmead, Callingwood North and West Edmonton, 7 days a week.

Summerlea coverage — we come to you
Garage-to-house firewall separations
Type X fire-rated board to code in Summerlea
Party walls and legal-suite separations
Basement legal-suite fire separations
Finished clean and inspection-ready
Joints taped as part of the rated assembly, not just for looks

What happens when an assembly is altered later

Every future trade is a risk

A rated Summerlea wall or ceiling stays rated only while nobody cuts an unsealed hole in it. Later work — a fan, a light, a duct, a speaker — can quietly undo it.

What we leave you

We photograph the rated work before covering it, so there is a record of what is behind the finish for whoever works on the house next.

Summerlea drywall in context

About Summerlea

Summerlea is the site of West Edmonton Mall, one of Edmonton's major attractions and a focus of shopping and entertainment activities.

What we see in Summerlea

In Summerlea the drywall work is popcorn and stipple ceiling removal, settling+truss-uplift cracks, nail pops, Poly-B repipe patching repipe patching. We confirm what your home actually needs on site, in writing, before anything starts.

Type X and Type C are not interchangeable

Two different boards

Type X is the common 5/8 inch rated board. Type C carries additional additives that resist shrinkage at high heat and is specified where an assembly — often a ceiling — depends on the board staying in place longer.

Substituting downward fails

Where drawings call for Type C, Type X is not an equivalent, and an inspector who spots it will fail the assembly. We order to the specification on your Summerlea drawings and tell you if what is on site does not match it.

Board thickness and why 5/8 is standard here

Not just thicker

Type X is 5/8 inch because the core needs that mass and the glass-fibre reinforcement to hold together as the gypsum calcines under heat.

The common error

Using 1/2 inch board in a rated Summerlea assembly because it is what was on site. It looks identical once finished and it is not the tested assembly. Board arriving on site is checked against the specification rather than assumed.

Our Summerlea fire-rated drywall process, step by step

Right board, right build-up

In Summerlea we confirm the required rating, then install the correct Type X board in the right layers — the assembly, not just the board, is what carries the rating.

Seal and finish

Penetrations and edges are where a rated assembly fails, so we firestop and seal them, then tape and finish the board clean. An Summerlea separation the inspector approves and the eye approves too.

Fire-rated drywall in a Summerlea garage ceiling

The most common one we do

Where Summerlea living space sits over a garage, the ceiling normally needs a rated separation. It is also the assembly most often found incomplete on older homes and DIY conversions — board up, joints untaped, pot lights cut straight through.

What we check before quoting

We look at what is above the ceiling, what is already installed, and whether the existing board is actually rated. Sometimes the honest answer is that the existing ceiling only needs its joints completed and its penetrations sealed rather than replacing.

What affects the cost of fire-rated drywall in Summerlea?

Area and assembly

The cost in Summerlea depends on the area and the rated assembly required — a single-layer garage ceiling is different from a two-layer party wall. The Summerlea rating drives the build-up, and Type X board carries a premium over standard. We price off the spec and a site look.

Passing inspection in Summerlea

The common rated jobs here are garages and suites. The rating only holds if the assembly is built and sealed exactly to spec, so we install it to code and seal penetrations properly so your Summerlea project passes the first time.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Summerlea Edmonton

Free quote

We come out to your Summerlea Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Summerlea Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Summerlea Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Summerlea Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Summerlea Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Summerlea Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Summerlea Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Summerlea Edmonton

Fire-Rated Drywall Summerlea Edmonton: your questions answered

Can pot lights go in a rated ceiling?: Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Summerlea ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.
Can you finish the fire-rated board too?: Yes — your Summerlea separation passes code and looks properly finished, ready for paint.
Do you handle the firestopping as well as the board?: We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.
How do I know which rated assembly my Summerlea project needs?: It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.
Will it pass inspection in Summerlea?: Yes — we install the correct Type X assembly and seal penetrations to spec so your Summerlea separation passes inspection.
Is Type X the same as fireproof?: No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Summerlea Edmonton

Type X board in Summerlea for garages, suites and mechanical rooms