How do I know which rated assembly my Strathcona project needs?

It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.

Do you stand behind your fire-rated work in Strathcona?

Yes. We install to code and walk the Strathcona job with you, and if something is not right we come back and make it right.

My Strathcona garage ceiling has board but the joints are open. Is that a problem?

Usually yes. Untaped joints are one of the most common reasons a garage separation is not complete, because the board looks installed. Often the fix is finishing the joints and sealing penetrations rather than replacing the ceiling.

Can I put an access hatch in my rated garage ceiling?

Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Strathcona garages where storage access was cut in afterwards and never addressed.

Can I use 1/2 inch board if that is what is on site?

Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

Do you handle the firestopping as well as the board?

We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.

Fire-Rated Drywall Strathcona Edmonton | Type X Board

Fire-rated drywall in Strathcona, built as a complete assembly

In Strathcona the code decides: garage separations, basement suites and party walls must carry Type X board in a rated assembly to pass inspection and protect the home. In Strathcona we install fire-rated drywall to code and finish it clean. Strathcona is this established Scona community where reno, repair and ceiling drywall are common, so fire-rated work here is common on garages and suites. We cover Strathcona, Allendale, Argyll, Belgravia and Scona, 7 days a week.

Penetrations firestopped before the finish goes on
Basement legal-suite fire separations
Strathcona coverage — we come to you
Rated assemblies installed and sealed correctly
Garage ceilings and garage-to-house separations in Strathcona
Finished clean and inspection-ready
Furnace and mechanical room enclosures

What makes drywall fire-rated in Strathcona

The board is only part of it

Type X board carries a glass-fibre reinforced core that holds together longer under heat. That is what earns the rating in a lab, but only inside a tested assembly: a stated board thickness, stud spacing, screw pattern and joint treatment.

Why that matters on your job

Putting Type X on a wall does not make the wall rated. In Strathcona we build the assembly the drawings specify, because an inspector is checking the system, not the sticker on the board.

Strathcona drywall in context

About Strathcona

Strathcona was named for Lord Strathcona, Hudson Bay Company Governor (1889-1914) and the man chosen to drive the "last spike" of the CPR transcontinental railway.

What we see in Strathcona

In Strathcona the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Joints, screws and the details inspectors actually check

The parts nobody photographs

A rated assembly in Strathcona depends on screw spacing, joints landing on framing, and joints being taped and filled. Loose screw spacing, unsupported butt joints and untaped joints are the usual reasons a rated wall does not pass.

Two-layer assemblies

Where the assembly is two layers, the second layer joints are offset from the first so no joint runs straight through the wall. That offset is part of the rating, not a finishing preference.

Finishing a rated wall in Strathcona without compromising it

Rated first, pretty second

Taping on a rated assembly in Strathcona does two jobs: it completes the fire separation and it produces the surface you will paint. The tape and fill on the rated joints is not optional cosmetic work.

Level of finish

Beyond the rated joint treatment, the visible finish level is your choice — a garage ceiling rarely needs the same finish as a living room. We will tell you where a higher level is worth paying for and where it is not.

Penetrations are where ratings are lost

Every hole is a path

Electrical boxes, plumbing, ducting and pot lights all pierce a rated wall or ceiling in Strathcona. Each one is a route for fire and smoke unless it is firestopped to suit the assembly.

Sequencing matters

Firestopping happens before the finish goes on. We coordinate with your other trades so penetrations are made and sealed before we tape, rather than cut into a finished rated ceiling afterwards and leave it open behind the paint.

Rated ceilings and the membrane above

Protecting the structure

A rated ceiling under living space is protecting the floor structure above it, which is why the board and its fastening are specified rather than optional.

Access hatches

Any hatch through it interrupts the assembly and needs a rated detail. It is a common find in Strathcona garages where storage access was cut in afterwards and never addressed.

Where Strathcona homes usually need rated board

The four common places

Most rated drywall in Strathcona houses is one of: the garage ceiling where living space sits above it, the garage-to-house wall, the furnace or mechanical room, and a legal-suite separation between dwelling units.

Renovations trigger it too

Finishing a basement, adding a suite or converting a garage often brings a separation into play that was not there before. If you are not sure whether your Strathcona project triggers one, that is a question for the building official at permit stage, and we will tell you when we think you should ask.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Strathcona Edmonton

Free quote

We come out to your Strathcona Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Strathcona Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Strathcona Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Strathcona Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Strathcona Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Strathcona Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Strathcona Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Strathcona Edmonton

Fire-Rated Drywall Strathcona Edmonton: your questions answered

How do I know which rated assembly my Strathcona project needs?: It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.
Do you stand behind your fire-rated work in Strathcona?: Yes. We install to code and walk the Strathcona job with you, and if something is not right we come back and make it right.
My Strathcona garage ceiling has board but the joints are open. Is that a problem?: Usually yes. Untaped joints are one of the most common reasons a garage separation is not complete, because the board looks installed. Often the fix is finishing the joints and sealing penetrations rather than replacing the ceiling.
Can I put an access hatch in my rated garage ceiling?: Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Strathcona garages where storage access was cut in afterwards and never addressed.
Can I use 1/2 inch board if that is what is on site?: Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.
Do you handle the firestopping as well as the board?: We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Strathcona Edmonton

Fire-rated drywall in Strathcona, built as a complete assembly