Do you stand behind your fire-rated work in Spruce Grove?

Yes. We install to code and walk the Spruce Grove job with you, and if something is not right we come back and make it right.

Do you handle the firestopping as well as the board?

We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.

Can I use 1/2 inch board if that is what is on site?

Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

Can you finish over rated board so it looks like the rest of the room?

Yes. The rated joint treatment comes first because it is part of the assembly, then the visible finish is taken to whatever level suits the room. A Spruce Grove garage ceiling and a living room do not need the same finish level.

What if someone cuts into it later?

That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.

Is Type X the same as fireproof?

No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.

Fire-Rated Drywall Spruce Grove | Type X Board

Fire-rated drywall in Spruce Grove, built as a complete assembly

A fire-rated wall is not a board, it is an assembly. In Spruce Grove that means the specified board thickness and type, the specified stud and screw spacing, taped joints, and every penetration firestopped. Miss any one of those and the rating is not there, whatever the board says on the back.

Garage ceilings and garage-to-house separations in Spruce Grove
Joints taped as part of the rated assembly, not just for looks
Rated assemblies installed and sealed correctly
Garage-to-house firewall separations
Party walls between units
Basement legal-suite fire separations
Penetrations firestopped before the finish goes on

Rated does not mean soundproof

Two different goals

People often assume a fire-rated Spruce Grove wall is also a sound wall. It is denser than a standard wall so it helps a little, but rating and acoustic performance are separate specifications.

When both are needed

A suite separation usually needs both, and they are built together. If sound is what you actually care about, we would rather design for that explicitly than let a rating imply it.

What makes drywall fire-rated in Spruce Grove

The board is only part of it

Type X board carries a glass-fibre reinforced core that holds together longer under heat. That is what earns the rating in a lab, but only inside a tested assembly: a stated board thickness, stud spacing, screw pattern and joint treatment.

Why that matters on your job

Putting Type X on a wall does not make the wall rated. In Spruce Grove we build the assembly the drawings specify, because an inspector is checking the system, not the sticker on the board.

Rated ceilings and the membrane above

Protecting the structure

A rated ceiling under living space is protecting the floor structure above it, which is why the board and its fastening are specified rather than optional.

Access hatches

Any hatch through it interrupts the assembly and needs a rated detail. It is a common find in Spruce Grove garages where storage access was cut in afterwards and never addressed.

Why Spruce Grove homeowners trust Emplastrum for fire-rated drywall

To code, and finished clean

A rated assembly has to be right for safety and inspection, and finished well for the room — in Spruce Grove we do both, installing to code and finishing flat.

Fixed price, same-day reply

We install fire-rated drywall across Spruce Grove and Edmonton, 7 days a week. Fixed pricing on free Spruce Grove quotes, a clean site and a guarantee on the work. When an Spruce Grove job is not right, we make it right — on us.

Our Spruce Grove fire-rated drywall process, step by step

Right board, right build-up

In Spruce Grove we confirm the required rating, then install the correct Type X board in the right layers — the assembly, not just the board, is what carries the rating.

Seal and finish

Penetrations and edges are where a rated assembly fails, so we firestop and seal them, then tape and finish the board clean. An Spruce Grove separation the inspector approves and the eye approves too.

Fire-rated drywall in a Spruce Grove garage ceiling

The most common one we do

Where Spruce Grove living space sits over a garage, the ceiling normally needs a rated separation. It is also the assembly most often found incomplete on older homes and DIY conversions — board up, joints untaped, pot lights cut straight through.

What we check before quoting

We look at what is above the ceiling, what is already installed, and whether the existing board is actually rated. Sometimes the honest answer is that the existing ceiling only needs its joints completed and its penetrations sealed rather than replacing.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Spruce Grove

Free quote

We come out to your Spruce Grove property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Spruce Grove starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Spruce Grove. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Spruce Grove home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Spruce Grove. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Spruce Grove Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Spruce Grove trusts for repair, restoration and finishing — rated on Google by Spruce Grove homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Spruce Grove.

Read our reviews on Google

FAQ — Fire-Rated Drywall Spruce Grove

Fire-Rated Drywall Spruce Grove: your questions answered

Do you stand behind your fire-rated work in Spruce Grove?: Yes. We install to code and walk the Spruce Grove job with you, and if something is not right we come back and make it right.
Do you handle the firestopping as well as the board?: We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.
Can I use 1/2 inch board if that is what is on site?: Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.
Can you finish over rated board so it looks like the rest of the room?: Yes. The rated joint treatment comes first because it is part of the assembly, then the visible finish is taken to whatever level suits the room. A Spruce Grove garage ceiling and a living room do not need the same finish level.
What if someone cuts into it later?: That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.
Is Type X the same as fireproof?: No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Spruce Grove

Fire-rated drywall in Spruce Grove, built as a complete assembly