Can I put an access hatch in my rated garage ceiling?

Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Rapperswill garages where storage access was cut in afterwards and never addressed.

What if someone cuts into it later?

That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.

Can you finish over rated board so it looks like the rest of the room?

Yes. The rated joint treatment comes first because it is part of the assembly, then the visible finish is taken to whatever level suits the room. A Rapperswill garage ceiling and a living room do not need the same finish level.

Can pot lights go in a rated ceiling?

Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Rapperswill ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.

My Rapperswill garage ceiling has board but the joints are open. Is that a problem?

Usually yes. Untaped joints are one of the most common reasons a garage separation is not complete, because the board looks installed. Often the fix is finishing the joints and sealing penetrations rather than replacing the ceiling.

Can I use 1/2 inch board if that is what is on site?

Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

Fire-Rated Drywall Rapperswill Edmonton | Type X Board

Type X board in Rapperswill for garages, suites and mechanical rooms

No shortcuts on Rapperswill fire-rating — separations, suites and party walls need code Type X rated assemblies to clear inspection and keep people safe. In Rapperswill we install fire-rated drywall to code and finish it clean. Rapperswill is an established south Edmonton community of 1960s-70s homes where ceiling stipple, settling cracks and dated texture are common, so fire-rated work here is common on garages and suites. We cover Rapperswill, Albany, Athlone, Baranow and Northwest, 7 days a week.

Rapperswill coverage — we come to you
Rated assemblies installed and sealed correctly
Garage ceilings and garage-to-house separations in Rapperswill
Furnace and mechanical room enclosures
Type X board to the assembly on the drawings
Finished clean and inspection-ready
Type X fire-rated board to code in Rapperswill

Common fire-rated situations in Rapperswill

In Rapperswill, rapperswill sits in Edmonton's Northwest district. Across roughly 780 homes here, the drywall work is first-year settling, basement dev for first owners, Level 5 over builder-grade. We cover Rapperswill and the surrounding Northwest district, 7 days a week. Same trusted team, same process on every job — on-site quote, fixed price, no surprises.

What makes drywall fire-rated in Rapperswill

The board is only part of it

Type X board carries a glass-fibre reinforced core that holds together longer under heat. That is what earns the rating in a lab, but only inside a tested assembly: a stated board thickness, stud spacing, screw pattern and joint treatment.

Why that matters on your job

Putting Type X on a wall does not make the wall rated. In Rapperswill we build the assembly the drawings specify, because an inspector is checking the system, not the sticker on the board.

Fire-rated drywall in a Rapperswill garage ceiling

The most common one we do

Where Rapperswill living space sits over a garage, the ceiling normally needs a rated separation. It is also the assembly most often found incomplete on older homes and DIY conversions — board up, joints untaped, pot lights cut straight through.

What we check before quoting

We look at what is above the ceiling, what is already installed, and whether the existing board is actually rated. Sometimes the honest answer is that the existing ceiling only needs its joints completed and its penetrations sealed rather than replacing.

Sealing at the top and bottom of a rated wall

The wall has to be continuous

A rated separation that stops at a suspended ceiling, or has a gap at the floor, is not a separation. Fire and smoke go over and under it.

Deck to deck

In an Rapperswill build the rated wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions where a wall was built to the ceiling and no further.

Why Rapperswill homeowners trust Emplastrum for fire-rated drywall

To code, and finished clean

A rated assembly has to be right for safety and inspection, and finished well for the room — in Rapperswill we do both, installing to code and finishing flat.

Fixed price, same-day reply

We install fire-rated drywall across Rapperswill and Northwest, 7 days a week. Fixed pricing on free Rapperswill quotes, a clean site and a guarantee on the work. When an Rapperswill job is not right, we make it right — on us.

Our Rapperswill fire-rated drywall process, step by step

Right board, right build-up

In Rapperswill we confirm the required rating, then install the correct Type X board in the right layers — the assembly, not just the board, is what carries the rating.

Seal and finish

Penetrations and edges are where a rated assembly fails, so we firestop and seal them, then tape and finish the board clean. An Rapperswill separation the inspector approves and the eye approves too.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Rapperswill Edmonton

Free quote

We come out to your Rapperswill Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Rapperswill Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Rapperswill Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Rapperswill Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Rapperswill Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Rapperswill Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Rapperswill Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Rapperswill Edmonton

Fire-Rated Drywall Rapperswill Edmonton: your questions answered

Can I put an access hatch in my rated garage ceiling?: Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Rapperswill garages where storage access was cut in afterwards and never addressed.
What if someone cuts into it later?: That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.
Can you finish over rated board so it looks like the rest of the room?: Yes. The rated joint treatment comes first because it is part of the assembly, then the visible finish is taken to whatever level suits the room. A Rapperswill garage ceiling and a living room do not need the same finish level.
Can pot lights go in a rated ceiling?: Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Rapperswill ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.
My Rapperswill garage ceiling has board but the joints are open. Is that a problem?: Usually yes. Untaped joints are one of the most common reasons a garage separation is not complete, because the board looks installed. Often the fix is finishing the joints and sealing penetrations rather than replacing the ceiling.
Can I use 1/2 inch board if that is what is on site?: Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Rapperswill Edmonton

Type X board in Rapperswill for garages, suites and mechanical rooms