Will it pass inspection in Pleasantview?

Yes — we install the correct Type X assembly and seal penetrations to spec so your Pleasantview separation passes inspection.

How do I know which rated assembly my Pleasantview project needs?

It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.

What if someone cuts into it later?

That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.

My Pleasantview garage ceiling has board but the joints are open. Is that a problem?

Usually yes. Untaped joints are one of the most common reasons a garage separation is not complete, because the board looks installed. Often the fix is finishing the joints and sealing penetrations rather than replacing the ceiling.

Can I put an access hatch in my rated garage ceiling?

Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Pleasantview garages where storage access was cut in afterwards and never addressed.

Do you install fire-rated drywall in Pleasantview?

Yes — fire-rated drywall in Pleasantview is part of our regular work, and we are usually booked within the week. We also cover Allendale, Argyll, Belgravia and Scona.

Fire-Rated Drywall Pleasantview Edmonton | Type X Board

Fire-rated drywall in Pleasantview, built as a complete assembly

No shortcuts on Pleasantview fire-rating — separations, suites and party walls need code Type X rated assemblies to clear inspection and keep people safe. In Pleasantview we install fire-rated drywall to code and finish it clean. Pleasantview is an established south Edmonton community of 1960s-70s homes where ceiling stipple, settling cracks and dated texture are common, so fire-rated work here is common on garages and suites. We cover Pleasantview, Allendale, Argyll, Belgravia and Scona, 7 days a week.

Party walls between units
Finished clean and inspection-ready
Garage ceilings and garage-to-house separations in Pleasantview
Party walls and legal-suite separations
Penetrations firestopped before the finish goes on
Rated assemblies installed and sealed correctly
Garage-to-house firewall separations

What affects the cost of fire-rated drywall in Pleasantview?

Area and assembly

The cost in Pleasantview depends on the area and the rated assembly required — a single-layer garage ceiling is different from a two-layer party wall. The Pleasantview rating drives the build-up, and Type X board carries a premium over standard. We price off the spec and a site look.

Passing inspection in Pleasantview

The common rated jobs here are garages and suites. The rating only holds if the assembly is built and sealed exactly to spec, so we install it to code and seal penetrations properly so your Pleasantview project passes the first time.

Pleasantview drywall in context

About Pleasantview

Close to Southgate Mall, the area's most prominent feature is its elevation: hence the name Pleasantview.

What we see in Pleasantview

In Pleasantview the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Type X and Type C are not interchangeable

Two different boards

Type X is the common 5/8 inch rated board. Type C carries additional additives that resist shrinkage at high heat and is specified where an assembly — often a ceiling — depends on the board staying in place longer.

Substituting downward fails

Where drawings call for Type C, Type X is not an equivalent, and an inspector who spots it will fail the assembly. We order to the specification on your Pleasantview drawings and tell you if what is on site does not match it.

Inspection, and what we hand over

Sequencing with your inspection

Rated assemblies in Pleasantview are usually inspected before the finish covers them, so we sequence boarding and firestopping to suit your inspection date rather than working ahead and covering something the inspector needs to see.

If something fails

If an assembly does not pass, we want to hear the inspector reason directly. Most failures are specific and fixable — a screw pattern, an untaped joint, an unsealed penetration — and are corrected faster from the actual note than from a second-hand summary.

Board thickness and why 5/8 is standard here

Not just thicker

Type X is 5/8 inch because the core needs that mass and the glass-fibre reinforcement to hold together as the gypsum calcines under heat.

The common error

Using 1/2 inch board in a rated Pleasantview assembly because it is what was on site. It looks identical once finished and it is not the tested assembly. Board arriving on site is checked against the specification rather than assumed.

Joints, screws and the details inspectors actually check

The parts nobody photographs

A rated assembly in Pleasantview depends on screw spacing, joints landing on framing, and joints being taped and filled. Loose screw spacing, unsupported butt joints and untaped joints are the usual reasons a rated wall does not pass.

Two-layer assemblies

Where the assembly is two layers, the second layer joints are offset from the first so no joint runs straight through the wall. That offset is part of the rating, not a finishing preference.

Fire-rated drywall in a Pleasantview garage ceiling

The most common one we do

Where Pleasantview living space sits over a garage, the ceiling normally needs a rated separation. It is also the assembly most often found incomplete on older homes and DIY conversions — board up, joints untaped, pot lights cut straight through.

What we check before quoting

We look at what is above the ceiling, what is already installed, and whether the existing board is actually rated. Sometimes the honest answer is that the existing ceiling only needs its joints completed and its penetrations sealed rather than replacing.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Pleasantview Edmonton

Free quote

We come out to your Pleasantview Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Pleasantview Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Pleasantview Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Pleasantview Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Pleasantview Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Pleasantview Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Pleasantview Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Pleasantview Edmonton

Fire-Rated Drywall Pleasantview Edmonton: your questions answered

Will it pass inspection in Pleasantview?: Yes — we install the correct Type X assembly and seal penetrations to spec so your Pleasantview separation passes inspection.
How do I know which rated assembly my Pleasantview project needs?: It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.
What if someone cuts into it later?: That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.
My Pleasantview garage ceiling has board but the joints are open. Is that a problem?: Usually yes. Untaped joints are one of the most common reasons a garage separation is not complete, because the board looks installed. Often the fix is finishing the joints and sealing penetrations rather than replacing the ceiling.
Can I put an access hatch in my rated garage ceiling?: Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Pleasantview garages where storage access was cut in afterwards and never addressed.
Do you install fire-rated drywall in Pleasantview?: Yes — fire-rated drywall in Pleasantview is part of our regular work, and we are usually booked within the week. We also cover Allendale, Argyll, Belgravia and Scona.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Pleasantview Edmonton

Fire-rated drywall in Pleasantview, built as a complete assembly