Is Type X the same as fireproof?

No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.

Do you stand behind your fire-rated work in Parkview?

Yes. We install to code and walk the Parkview job with you, and if something is not right we come back and make it right.

Will it pass inspection in Parkview?

Yes — we install the correct Type X assembly and seal penetrations to spec so your Parkview separation passes inspection.

What if someone cuts into it later?

That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.

Can you finish over rated board so it looks like the rest of the room?

Yes. The rated joint treatment comes first because it is part of the assembly, then the visible finish is taken to whatever level suits the room. A Parkview garage ceiling and a living room do not need the same finish level.

Where is fire-rated drywall required?

The standard Parkview fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Parkview project needs.

Fire-Rated Drywall Parkview Edmonton | Type X Board

Fire-rated drywall in Parkview, built as a complete assembly

Most fire-rated work we do in Parkview is one of four things: a garage ceiling under living space, a party wall between units, a furnace or mechanical room, or a legal-suite separation. Each has its own assembly, and the drawings or the building official decide which one applies — not us and not the supplier.

Basement legal-suite fire separations
Penetrations firestopped before the finish goes on
Type X fire-rated board to code in Parkview
Parkview coverage — we come to you
Finished clean and inspection-ready
Joints taped as part of the rated assembly, not just for looks
Party walls between units

What affects the cost of fire-rated drywall in Parkview?

Area and assembly

The cost in Parkview depends on the area and the rated assembly required — a single-layer garage ceiling is different from a two-layer party wall. The Parkview rating drives the build-up, and Type X board carries a premium over standard. We price off the spec and a site look.

Passing inspection in Parkview

The common rated jobs here are garages and suites. The rating only holds if the assembly is built and sealed exactly to spec, so we install it to code and seal penetrations properly so your Parkview project passes the first time.

Parkview drywall in context

About Parkview

One of the City's larger neighbourhoods, dating to the 1950s, Parkview is a beautiful area featuring mature trees, attractively landscaped homes on quiet streets, and breathtaking views of the river valley.

What we see in Parkview

In Parkview the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Board thickness and why 5/8 is standard here

Not just thicker

Type X is 5/8 inch because the core needs that mass and the glass-fibre reinforcement to hold together as the gypsum calcines under heat.

The common error

Using 1/2 inch board in a rated Parkview assembly because it is what was on site. It looks identical once finished and it is not the tested assembly. Board arriving on site is checked against the specification rather than assumed.

Our Parkview fire-rated drywall process, step by step

Right board, right build-up

In Parkview we confirm the required rating, then install the correct Type X board in the right layers — the assembly, not just the board, is what carries the rating.

Seal and finish

Penetrations and edges are where a rated assembly fails, so we firestop and seal them, then tape and finish the board clean. An Parkview separation the inspector approves and the eye approves too.

Rated ceilings and the membrane above

Protecting the structure

A rated ceiling under living space is protecting the floor structure above it, which is why the board and its fastening are specified rather than optional.

Access hatches

Any hatch through it interrupts the assembly and needs a rated detail. It is a common find in Parkview garages where storage access was cut in afterwards and never addressed.

Rated does not mean soundproof

Two different goals

People often assume a fire-rated Parkview wall is also a sound wall. It is denser than a standard wall so it helps a little, but rating and acoustic performance are separate specifications.

When both are needed

A suite separation usually needs both, and they are built together. If sound is what you actually care about, we would rather design for that explicitly than let a rating imply it.

Coordinating with the electrician early

Boxes in rated walls

Outlet and switch boxes in a rated Parkview assembly need treatment — spacing rules, pads or listed boxes — and back-to-back boxes are a particular problem.

Why early matters

Rearranging a box after board is up means opening a rated wall. Walking the wall with the electrician before boarding takes ten minutes and avoids that entirely.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Parkview Edmonton

Free quote

We come out to your Parkview Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Parkview Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Parkview Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Parkview Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Parkview Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Parkview Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Parkview Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Parkview Edmonton

Fire-Rated Drywall Parkview Edmonton: your questions answered

Is Type X the same as fireproof?: No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.
Do you stand behind your fire-rated work in Parkview?: Yes. We install to code and walk the Parkview job with you, and if something is not right we come back and make it right.
Will it pass inspection in Parkview?: Yes — we install the correct Type X assembly and seal penetrations to spec so your Parkview separation passes inspection.
What if someone cuts into it later?: That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.
Can you finish over rated board so it looks like the rest of the room?: Yes. The rated joint treatment comes first because it is part of the assembly, then the visible finish is taken to whatever level suits the room. A Parkview garage ceiling and a living room do not need the same finish level.
Where is fire-rated drywall required?: The standard Parkview fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Parkview project needs.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Parkview Edmonton

Fire-rated drywall in Parkview, built as a complete assembly