What if someone cuts into it later?

That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.

Does the rated wall have to go above the ceiling?

Yes. A separation that stops at a suspended ceiling is not a separation — fire and smoke go over it. The wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions.

Where is fire-rated drywall required?

The standard Overlanders fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Overlanders project needs.

Can pot lights go in a rated ceiling?

Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Overlanders ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.

Do you install fire-rated drywall in Overlanders?

Yes — fire-rated drywall in Overlanders is part of our regular work, and we are usually booked within the week. We also cover Balwin, Bannerman, Belmont and Northeast.

Can you finish the fire-rated board too?

Yes — your Overlanders separation passes code and looks properly finished, ready for paint.

Fire-Rated Drywall Overlanders Edmonton | Type X Board

Type X board in Overlanders for garages, suites and mechanical rooms

In Overlanders the code decides: garage separations, basement suites and party walls must carry Type X board in a rated assembly to pass inspection and protect the home. In Overlanders we install fire-rated drywall to code and finish it clean. Overlanders is this established Northeast community where reno, repair and ceiling drywall are common, so fire-rated work here is common on garages and suites. We cover Overlanders, Balwin, Bannerman, Belmont and Northeast, 7 days a week.

Finished clean and inspection-ready
Overlanders coverage — we come to you
Penetrations firestopped before the finish goes on
Party walls between units
Garage-to-house firewall separations
Joints taped as part of the rated assembly, not just for looks
Furnace and mechanical room enclosures

Joints, screws and the details inspectors actually check

The parts nobody photographs

A rated assembly in Overlanders depends on screw spacing, joints landing on framing, and joints being taped and filled. Loose screw spacing, unsupported butt joints and untaped joints are the usual reasons a rated wall does not pass.

Two-layer assemblies

Where the assembly is two layers, the second layer joints are offset from the first so no joint runs straight through the wall. That offset is part of the rating, not a finishing preference.

Overlanders drywall in context

About Overlanders

In 1875 an Anglican minister built a church, home and hospital which he called the Hermitage, a name which is now used to describe the three neighbourhoods in this area.

What we see in Overlanders

In Overlanders the drywall work is popcorn and stipple ceiling removal, settling+truss-uplift cracks, nail pops, Poly-B repipe patching repipe patching. We confirm what your home actually needs on site, in writing, before anything starts.

Fire-rated drywall in a Overlanders garage ceiling

The most common one we do

Where Overlanders living space sits over a garage, the ceiling normally needs a rated separation. It is also the assembly most often found incomplete on older homes and DIY conversions — board up, joints untaped, pot lights cut straight through.

What we check before quoting

We look at what is above the ceiling, what is already installed, and whether the existing board is actually rated. Sometimes the honest answer is that the existing ceiling only needs its joints completed and its penetrations sealed rather than replacing.

Coordinating with the electrician early

Boxes in rated walls

Outlet and switch boxes in a rated Overlanders assembly need treatment — spacing rules, pads or listed boxes — and back-to-back boxes are a particular problem.

Why early matters

Rearranging a box after board is up means opening a rated wall. Walking the wall with the electrician before boarding takes ten minutes and avoids that entirely.

Type X and Type C are not interchangeable

Two different boards

Type X is the common 5/8 inch rated board. Type C carries additional additives that resist shrinkage at high heat and is specified where an assembly — often a ceiling — depends on the board staying in place longer.

Substituting downward fails

Where drawings call for Type C, Type X is not an equivalent, and an inspector who spots it will fail the assembly. We order to the specification on your Overlanders drawings and tell you if what is on site does not match it.

Fire-rated garages, suites and party walls in Overlanders

Garage firewalls

The most common fire-rated job in Overlanders is the garage-to-house separation — Type X board on the common wall and ceiling. Code-compliant install and finish.

Legal suites and shared walls

Frequent work in Overlanders homes and multi-unit buildings. We build the rated separations these require. See our legal suite drywall page.

Board thickness and why 5/8 is standard here

Not just thicker

Type X is 5/8 inch because the core needs that mass and the glass-fibre reinforcement to hold together as the gypsum calcines under heat.

The common error

Using 1/2 inch board in a rated Overlanders assembly because it is what was on site. It looks identical once finished and it is not the tested assembly. Board arriving on site is checked against the specification rather than assumed.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Overlanders Edmonton

Free quote

We come out to your Overlanders Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Overlanders Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Overlanders Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Overlanders Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Overlanders Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Overlanders Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Overlanders Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Overlanders Edmonton

Fire-Rated Drywall Overlanders Edmonton: your questions answered

What if someone cuts into it later?: That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.
Does the rated wall have to go above the ceiling?: Yes. A separation that stops at a suspended ceiling is not a separation — fire and smoke go over it. The wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions.
Where is fire-rated drywall required?: The standard Overlanders fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Overlanders project needs.
Can pot lights go in a rated ceiling?: Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Overlanders ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.
Do you install fire-rated drywall in Overlanders?: Yes — fire-rated drywall in Overlanders is part of our regular work, and we are usually booked within the week. We also cover Balwin, Bannerman, Belmont and Northeast.
Can you finish the fire-rated board too?: Yes — your Overlanders separation passes code and looks properly finished, ready for paint.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Overlanders Edmonton

Type X board in Overlanders for garages, suites and mechanical rooms