What if someone cuts into it later?

That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.

Do you stand behind your fire-rated work in Ogilvie Ridge?

Yes. We install to code and walk the Ogilvie Ridge job with you, and if something is not right we come back and make it right.

Can you finish over rated board so it looks like the rest of the room?

Yes. The rated joint treatment comes first because it is part of the assembly, then the visible finish is taken to whatever level suits the room. A Ogilvie Ridge garage ceiling and a living room do not need the same finish level.

Can I use 1/2 inch board if that is what is on site?

Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

Is a fire-rated wall also soundproof?

It helps a little because it is denser, but rating and acoustic performance are separate specifications. A suite separation usually needs both, built together. If sound is the real goal we would rather design for it explicitly.

Can I put an access hatch in my rated garage ceiling?

Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Ogilvie Ridge garages where storage access was cut in afterwards and never addressed.

Fire-Rated Drywall Ogilvie Ridge Edmonton | Type X Board

Fire-rated drywall in Ogilvie Ridge, installed to code

Most fire-rated work we do in Ogilvie Ridge is one of four things: a garage ceiling under living space, a party wall between units, a furnace or mechanical room, or a legal-suite separation. Each has its own assembly, and the drawings or the building official decide which one applies — not us and not the supplier.

Garage-to-house firewall separations
Party walls and legal-suite separations
Type X board to the assembly on the drawings
Basement legal-suite fire separations
Ogilvie Ridge coverage — we come to you
Garage ceilings and garage-to-house separations in Ogilvie Ridge
Type X fire-rated board to code in Ogilvie Ridge

What affects the cost of fire-rated drywall in Ogilvie Ridge?

Area and assembly

The cost in Ogilvie Ridge depends on the area and the rated assembly required — a single-layer garage ceiling is different from a two-layer party wall. The Ogilvie Ridge rating drives the build-up, and Type X board carries a premium over standard. We price off the spec and a site look.

Passing inspection in Ogilvie Ridge

The common rated jobs here are garages and suites. The rating only holds if the assembly is built and sealed exactly to spec, so we install it to code and seal penetrations properly so your Ogilvie Ridge project passes the first time.

Penetrations are where ratings are lost

Every hole is a path

Electrical boxes, plumbing, ducting and pot lights all pierce a rated wall or ceiling in Ogilvie Ridge. Each one is a route for fire and smoke unless it is firestopped to suit the assembly.

Sequencing matters

Firestopping happens before the finish goes on. We coordinate with your other trades so penetrations are made and sealed before we tape, rather than cut into a finished rated ceiling afterwards and leave it open behind the paint.

One-hour and two-hour assemblies

What the number means

A rating is how long a tested assembly resisted fire under laboratory conditions, not a guarantee about your Ogilvie Ridge house. One hour is the common residential separation; two hour appears between units in some buildings.

Why it changes the build

A two-hour assembly is usually two layers of board with offset joints, which changes material, labour and thickness. It is specified on the drawings and it is not something to substitute down.

Inspection, and what we hand over

Sequencing with your inspection

Rated assemblies in Ogilvie Ridge are usually inspected before the finish covers them, so we sequence boarding and firestopping to suit your inspection date rather than working ahead and covering something the inspector needs to see.

If something fails

If an assembly does not pass, we want to hear the inspector reason directly. Most failures are specific and fixable — a screw pattern, an untaped joint, an unsealed penetration — and are corrected faster from the actual note than from a second-hand summary.

Sealing at the top and bottom of a rated wall

The wall has to be continuous

A rated separation that stops at a suspended ceiling, or has a gap at the floor, is not a separation. Fire and smoke go over and under it.

Deck to deck

In an Ogilvie Ridge build the rated wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions where a wall was built to the ceiling and no further.

Board thickness and why 5/8 is standard here

Not just thicker

Type X is 5/8 inch because the core needs that mass and the glass-fibre reinforcement to hold together as the gypsum calcines under heat.

The common error

Using 1/2 inch board in a rated Ogilvie Ridge assembly because it is what was on site. It looks identical once finished and it is not the tested assembly. Board arriving on site is checked against the specification rather than assumed.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Ogilvie Ridge Edmonton

Free quote

We come out to your Ogilvie Ridge Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Ogilvie Ridge Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Ogilvie Ridge Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Ogilvie Ridge Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Ogilvie Ridge Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Ogilvie Ridge Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Ogilvie Ridge Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Ogilvie Ridge Edmonton

Fire-Rated Drywall Ogilvie Ridge Edmonton: your questions answered

What if someone cuts into it later?: That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.
Do you stand behind your fire-rated work in Ogilvie Ridge?: Yes. We install to code and walk the Ogilvie Ridge job with you, and if something is not right we come back and make it right.
Can you finish over rated board so it looks like the rest of the room?: Yes. The rated joint treatment comes first because it is part of the assembly, then the visible finish is taken to whatever level suits the room. A Ogilvie Ridge garage ceiling and a living room do not need the same finish level.
Can I use 1/2 inch board if that is what is on site?: Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.
Is a fire-rated wall also soundproof?: It helps a little because it is denser, but rating and acoustic performance are separate specifications. A suite separation usually needs both, built together. If sound is the real goal we would rather design for it explicitly.
Can I put an access hatch in my rated garage ceiling?: Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Ogilvie Ridge garages where storage access was cut in afterwards and never addressed.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Ogilvie Ridge Edmonton

Fire-rated drywall in Ogilvie Ridge, installed to code