Do you install fire-rated drywall in Montrose?

Yes — fire-rated drywall in Montrose is part of our regular work, and we are usually booked within the week. We also cover Abbottsfield, Alberta Avenue, Beacon Heights and North Central.

Is Type X the same as fireproof?

No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.

How do I know which rated assembly my Montrose project needs?

It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.

Will it pass inspection in Montrose?

Yes — we install the correct Type X assembly and seal penetrations to spec so your Montrose separation passes inspection.

Can I put an access hatch in my rated garage ceiling?

Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Montrose garages where storage access was cut in afterwards and never addressed.

Where is fire-rated drywall required?

The standard Montrose fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Montrose project needs.

Fire-Rated Drywall Montrose Edmonton | Type X Board

Type X board in Montrose for garages, suites and mechanical rooms

No shortcuts on Montrose fire-rating — separations, suites and party walls need code Type X rated assemblies to clear inspection and keep people safe. In Montrose we install fire-rated drywall to code and finish it clean. Montrose is one of North Central's newer communities, where fresh installation and first-year settling work are common, so fire-rated work here is common on garages and suites. We cover Montrose, Abbottsfield, Alberta Avenue, Beacon Heights and North Central, 7 days a week.

Garage ceilings and garage-to-house separations in Montrose
Furnace and mechanical room enclosures
Joints taped as part of the rated assembly, not just for looks
Type X fire-rated board to code in Montrose
Party walls and legal-suite separations
Type X board to the assembly on the drawings
Rated assemblies installed and sealed correctly

What happens when an assembly is altered later

Every future trade is a risk

A rated Montrose wall or ceiling stays rated only while nobody cuts an unsealed hole in it. Later work — a fan, a light, a duct, a speaker — can quietly undo it.

What we leave you

We photograph the rated work before covering it, so there is a record of what is behind the finish for whoever works on the house next.

Montrose drywall in context

About Montrose

Most of Montrose was developed prior to 1950, and the remainder completed before 1960.

What we see in Montrose

In Montrose the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

One-hour and two-hour assemblies

What the number means

A rating is how long a tested assembly resisted fire under laboratory conditions, not a guarantee about your Montrose house. One hour is the common residential separation; two hour appears between units in some buildings.

Why it changes the build

A two-hour assembly is usually two layers of board with offset joints, which changes material, labour and thickness. It is specified on the drawings and it is not something to substitute down.

Inspection, and what we hand over

Sequencing with your inspection

Rated assemblies in Montrose are usually inspected before the finish covers them, so we sequence boarding and firestopping to suit your inspection date rather than working ahead and covering something the inspector needs to see.

If something fails

If an assembly does not pass, we want to hear the inspector reason directly. Most failures are specific and fixable — a screw pattern, an untaped joint, an unsealed penetration — and are corrected faster from the actual note than from a second-hand summary.

Our Montrose fire-rated drywall process, step by step

Right board, right build-up

In Montrose we confirm the required rating, then install the correct Type X board in the right layers — the assembly, not just the board, is what carries the rating.

Seal and finish

Penetrations and edges are where a rated assembly fails, so we firestop and seal them, then tape and finish the board clean. An Montrose separation the inspector approves and the eye approves too.

Where Montrose homes usually need rated board

The four common places

Most rated drywall in Montrose houses is one of: the garage ceiling where living space sits above it, the garage-to-house wall, the furnace or mechanical room, and a legal-suite separation between dwelling units.

Renovations trigger it too

Finishing a basement, adding a suite or converting a garage often brings a separation into play that was not there before. If you are not sure whether your Montrose project triggers one, that is a question for the building official at permit stage, and we will tell you when we think you should ask.

Type X and Type C are not interchangeable

Two different boards

Type X is the common 5/8 inch rated board. Type C carries additional additives that resist shrinkage at high heat and is specified where an assembly — often a ceiling — depends on the board staying in place longer.

Substituting downward fails

Where drawings call for Type C, Type X is not an equivalent, and an inspector who spots it will fail the assembly. We order to the specification on your Montrose drawings and tell you if what is on site does not match it.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Montrose Edmonton

Free quote

We come out to your Montrose Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Montrose Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Montrose Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Montrose Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Montrose Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Montrose Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Montrose Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Montrose Edmonton

Fire-Rated Drywall Montrose Edmonton: your questions answered

Do you install fire-rated drywall in Montrose?: Yes — fire-rated drywall in Montrose is part of our regular work, and we are usually booked within the week. We also cover Abbottsfield, Alberta Avenue, Beacon Heights and North Central.
Is Type X the same as fireproof?: No. Type X resists fire for a stated period inside a tested assembly, which buys time to get out. Nothing about it makes a wall fireproof, and the rating only holds if the whole assembly — board, spacing, joints and penetrations — is built as specified.
How do I know which rated assembly my Montrose project needs?: It comes from your drawings or from the building official at permit stage, not from us and not from the board supplier. We build to the assembly you have been given, and if what is specified does not match what is on site we will tell you before boarding.
Will it pass inspection in Montrose?: Yes — we install the correct Type X assembly and seal penetrations to spec so your Montrose separation passes inspection.
Can I put an access hatch in my rated garage ceiling?: Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Montrose garages where storage access was cut in afterwards and never addressed.
Where is fire-rated drywall required?: The standard Montrose fire-rating locations: garage-to-house walls, basement suites and party walls between units. We confirm what your Montrose project needs.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Montrose Edmonton

Type X board in Montrose for garages, suites and mechanical rooms