Can you finish the fire-rated board too?

Yes — your Malmo Plains separation passes code and looks properly finished, ready for paint.

Do you install fire-rated drywall in Malmo Plains?

Yes — fire-rated drywall in Malmo Plains is part of our regular work, and we are usually booked within the week. We also cover Allendale, Argyll, Belgravia and Scona.

Do you handle the firestopping as well as the board?

We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.

Can I use 1/2 inch board if that is what is on site?

Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

Do you stand behind your fire-rated work in Malmo Plains?

Yes. We install to code and walk the Malmo Plains job with you, and if something is not right we come back and make it right.

Can pot lights go in a rated ceiling?

Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Malmo Plains ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.

Fire-Rated Drywall Malmo Plains Edmonton | Type X Board

Fire-rated drywall in Malmo Plains, installed to code

Most fire-rated work we do in Malmo Plains is one of four things: a garage ceiling under living space, a party wall between units, a furnace or mechanical room, or a legal-suite separation. Each has its own assembly, and the drawings or the building official decide which one applies — not us and not the supplier.

Finished clean and inspection-ready
Joints taped as part of the rated assembly, not just for looks
Rated assemblies installed and sealed correctly
Type X board to the assembly on the drawings
Malmo Plains coverage — we come to you
Party walls between units
Penetrations firestopped before the finish goes on

Rated does not mean soundproof

Two different goals

People often assume a fire-rated Malmo Plains wall is also a sound wall. It is denser than a standard wall so it helps a little, but rating and acoustic performance are separate specifications.

When both are needed

A suite separation usually needs both, and they are built together. If sound is what you actually care about, we would rather design for that explicitly than let a rating imply it.

Malmo Plains drywall in context

About Malmo Plains

Most of the land within the present neighbourhood was at one time part of the University of Alberta research farm.

What we see in Malmo Plains

In Malmo Plains the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Type X and Type C are not interchangeable

Two different boards

Type X is the common 5/8 inch rated board. Type C carries additional additives that resist shrinkage at high heat and is specified where an assembly — often a ceiling — depends on the board staying in place longer.

Substituting downward fails

Where drawings call for Type C, Type X is not an equivalent, and an inspector who spots it will fail the assembly. We order to the specification on your Malmo Plains drawings and tell you if what is on site does not match it.

Our Malmo Plains fire-rated drywall process, step by step

Right board, right build-up

In Malmo Plains we confirm the required rating, then install the correct Type X board in the right layers — the assembly, not just the board, is what carries the rating.

Seal and finish

Penetrations and edges are where a rated assembly fails, so we firestop and seal them, then tape and finish the board clean. An Malmo Plains separation the inspector approves and the eye approves too.

What happens when an assembly is altered later

Every future trade is a risk

A rated Malmo Plains wall or ceiling stays rated only while nobody cuts an unsealed hole in it. Later work — a fan, a light, a duct, a speaker — can quietly undo it.

What we leave you

We photograph the rated work before covering it, so there is a record of what is behind the finish for whoever works on the house next.

Fire-rated garages, suites and party walls in Malmo Plains

Garage firewalls

The most common fire-rated job in Malmo Plains is the garage-to-house separation — Type X board on the common wall and ceiling. Code-compliant install and finish.

Legal suites and shared walls

Frequent work in Malmo Plains homes and multi-unit buildings. We build the rated separations these require. See our legal suite drywall page.

Where Malmo Plains homes usually need rated board

The four common places

Most rated drywall in Malmo Plains houses is one of: the garage ceiling where living space sits above it, the garage-to-house wall, the furnace or mechanical room, and a legal-suite separation between dwelling units.

Renovations trigger it too

Finishing a basement, adding a suite or converting a garage often brings a separation into play that was not there before. If you are not sure whether your Malmo Plains project triggers one, that is a question for the building official at permit stage, and we will tell you when we think you should ask.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Malmo Plains Edmonton

Free quote

We come out to your Malmo Plains Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Malmo Plains Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Malmo Plains Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Malmo Plains Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Malmo Plains Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Malmo Plains Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Malmo Plains Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Malmo Plains Edmonton

Fire-Rated Drywall Malmo Plains Edmonton: your questions answered

Can you finish the fire-rated board too?: Yes — your Malmo Plains separation passes code and looks properly finished, ready for paint.
Do you install fire-rated drywall in Malmo Plains?: Yes — fire-rated drywall in Malmo Plains is part of our regular work, and we are usually booked within the week. We also cover Allendale, Argyll, Belgravia and Scona.
Do you handle the firestopping as well as the board?: We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.
Can I use 1/2 inch board if that is what is on site?: Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.
Do you stand behind your fire-rated work in Malmo Plains?: Yes. We install to code and walk the Malmo Plains job with you, and if something is not right we come back and make it right.
Can pot lights go in a rated ceiling?: Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Malmo Plains ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Malmo Plains Edmonton

Fire-rated drywall in Malmo Plains, installed to code