Can you finish the fire-rated board too?

Yes — your Lee Ridge separation passes code and looks properly finished, ready for paint.

Can pot lights go in a rated ceiling?

Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Lee Ridge ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.

Will it pass inspection in Lee Ridge?

Yes — we install the correct Type X assembly and seal penetrations to spec so your Lee Ridge separation passes inspection.

What if someone cuts into it later?

That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.

My Lee Ridge garage ceiling has board but the joints are open. Is that a problem?

Usually yes. Untaped joints are one of the most common reasons a garage separation is not complete, because the board looks installed. Often the fix is finishing the joints and sealing penetrations rather than replacing the ceiling.

Can I put an access hatch in my rated garage ceiling?

Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Lee Ridge garages where storage access was cut in afterwards and never addressed.

Fire-Rated Drywall Lee Ridge Edmonton | Type X Board

Fire-rated drywall in Lee Ridge, built as a complete assembly

Most fire-rated work we do in Lee Ridge is one of four things: a garage ceiling under living space, a party wall between units, a furnace or mechanical room, or a legal-suite separation. Each has its own assembly, and the drawings or the building official decide which one applies — not us and not the supplier.

Lee Ridge coverage — we come to you
Furnace and mechanical room enclosures
Rated assemblies installed and sealed correctly
Garage-to-house firewall separations
Type X fire-rated board to code in Lee Ridge
Type X board to the assembly on the drawings
Party walls between units

What affects the cost of fire-rated drywall in Lee Ridge?

Area and assembly

The cost in Lee Ridge depends on the area and the rated assembly required — a single-layer garage ceiling is different from a two-layer party wall. The Lee Ridge rating drives the build-up, and Type X board carries a premium over standard. We price off the spec and a site look.

Passing inspection in Lee Ridge

The common rated jobs here are garages and suites. The rating only holds if the assembly is built and sealed exactly to spec, so we install it to code and seal penetrations properly so your Lee Ridge project passes the first time.

Lee Ridge drywall in context

About Lee Ridge

Lee Ridge, named for Robert Lee (Mayor of Edmonton, 1909 - 1910), is one of the 27 neighbourhoods of Mill Woods.

What we see in Lee Ridge

In Lee Ridge the drywall work is plaster and lath repair, popcorn and stipple ceiling removal, careful patching into original surfaces. We confirm what your home actually needs on site, in writing, before anything starts.

Joints, screws and the details inspectors actually check

The parts nobody photographs

A rated assembly in Lee Ridge depends on screw spacing, joints landing on framing, and joints being taped and filled. Loose screw spacing, unsupported butt joints and untaped joints are the usual reasons a rated wall does not pass.

Two-layer assemblies

Where the assembly is two layers, the second layer joints are offset from the first so no joint runs straight through the wall. That offset is part of the rating, not a finishing preference.

Penetrations are where ratings are lost

Every hole is a path

Electrical boxes, plumbing, ducting and pot lights all pierce a rated wall or ceiling in Lee Ridge. Each one is a route for fire and smoke unless it is firestopped to suit the assembly.

Sequencing matters

Firestopping happens before the finish goes on. We coordinate with your other trades so penetrations are made and sealed before we tape, rather than cut into a finished rated ceiling afterwards and leave it open behind the paint.

Fire-rated drywall in a Lee Ridge garage ceiling

The most common one we do

Where Lee Ridge living space sits over a garage, the ceiling normally needs a rated separation. It is also the assembly most often found incomplete on older homes and DIY conversions — board up, joints untaped, pot lights cut straight through.

What we check before quoting

We look at what is above the ceiling, what is already installed, and whether the existing board is actually rated. Sometimes the honest answer is that the existing ceiling only needs its joints completed and its penetrations sealed rather than replacing.

Finishing a rated wall in Lee Ridge without compromising it

Rated first, pretty second

Taping on a rated assembly in Lee Ridge does two jobs: it completes the fire separation and it produces the surface you will paint. The tape and fill on the rated joints is not optional cosmetic work.

Level of finish

Beyond the rated joint treatment, the visible finish level is your choice — a garage ceiling rarely needs the same finish as a living room. We will tell you where a higher level is worth paying for and where it is not.

Board thickness and why 5/8 is standard here

Not just thicker

Type X is 5/8 inch because the core needs that mass and the glass-fibre reinforcement to hold together as the gypsum calcines under heat.

The common error

Using 1/2 inch board in a rated Lee Ridge assembly because it is what was on site. It looks identical once finished and it is not the tested assembly. Board arriving on site is checked against the specification rather than assumed.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Lee Ridge Edmonton

Free quote

We come out to your Lee Ridge Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Lee Ridge Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Lee Ridge Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Lee Ridge Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Lee Ridge Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Lee Ridge Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Lee Ridge Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Lee Ridge Edmonton

Fire-Rated Drywall Lee Ridge Edmonton: your questions answered

Can you finish the fire-rated board too?: Yes — your Lee Ridge separation passes code and looks properly finished, ready for paint.
Can pot lights go in a rated ceiling?: Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Lee Ridge ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.
Will it pass inspection in Lee Ridge?: Yes — we install the correct Type X assembly and seal penetrations to spec so your Lee Ridge separation passes inspection.
What if someone cuts into it later?: That is the risk — a fan, a light or a duct added later can quietly undo the assembly. We photograph the rated work before covering it so there is a record of what is behind the finish for whoever works on the house next.
My Lee Ridge garage ceiling has board but the joints are open. Is that a problem?: Usually yes. Untaped joints are one of the most common reasons a garage separation is not complete, because the board looks installed. Often the fix is finishing the joints and sealing penetrations rather than replacing the ceiling.
Can I put an access hatch in my rated garage ceiling?: Only with a rated detail. Any hatch interrupts the assembly. It is a common find in Lee Ridge garages where storage access was cut in afterwards and never addressed.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Lee Ridge Edmonton

Fire-rated drywall in Lee Ridge, built as a complete assembly