Will it pass inspection in Klarvatten?

Yes — we install the correct Type X assembly and seal penetrations to spec so your Klarvatten separation passes inspection.

Do you handle the firestopping as well as the board?

We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.

Can I use 1/2 inch board if that is what is on site?

Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.

Can pot lights go in a rated ceiling?

Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Klarvatten ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.

Do you install fire-rated drywall in Klarvatten?

Yes — fire-rated drywall in Klarvatten is part of our regular work, and we are usually booked within the week. We also cover Albany, Athlone, Baranow and Northwest.

My Klarvatten garage ceiling has board but the joints are open. Is that a problem?

Usually yes. Untaped joints are one of the most common reasons a garage separation is not complete, because the board looks installed. Often the fix is finishing the joints and sealing penetrations rather than replacing the ceiling.

Fire-Rated Drywall Klarvatten Edmonton | Type X Board

Fire-rated drywall in Klarvatten, installed to code

In Klarvatten the code decides: garage separations, basement suites and party walls must carry Type X board in a rated assembly to pass inspection and protect the home. In Klarvatten we install fire-rated drywall to code and finish it clean. Klarvatten is an Northwest community with a mix of older homes and newer builds, so fire-rated work here is common on garages and suites. We cover Klarvatten, Albany, Athlone, Baranow and Northwest, 7 days a week.

Rated assemblies installed and sealed correctly
Furnace and mechanical room enclosures
Basement legal-suite fire separations
Type X board to the assembly on the drawings
Joints taped as part of the rated assembly, not just for looks
Penetrations firestopped before the finish goes on
Finished clean and inspection-ready

Finishing a rated wall in Klarvatten without compromising it

Rated first, pretty second

Taping on a rated assembly in Klarvatten does two jobs: it completes the fire separation and it produces the surface you will paint. The tape and fill on the rated joints is not optional cosmetic work.

Level of finish

Beyond the rated joint treatment, the visible finish level is your choice — a garage ceiling rarely needs the same finish as a living room. We will tell you where a higher level is worth paying for and where it is not.

Inspection, and what we hand over

Sequencing with your inspection

Rated assemblies in Klarvatten are usually inspected before the finish covers them, so we sequence boarding and firestopping to suit your inspection date rather than working ahead and covering something the inspector needs to see.

If something fails

If an assembly does not pass, we want to hear the inspector reason directly. Most failures are specific and fixable — a screw pattern, an untaped joint, an unsealed penetration — and are corrected faster from the actual note than from a second-hand summary.

Rated does not mean soundproof

Two different goals

People often assume a fire-rated Klarvatten wall is also a sound wall. It is denser than a standard wall so it helps a little, but rating and acoustic performance are separate specifications.

When both are needed

A suite separation usually needs both, and they are built together. If sound is what you actually care about, we would rather design for that explicitly than let a rating imply it.

Sealing at the top and bottom of a rated wall

The wall has to be continuous

A rated separation that stops at a suspended ceiling, or has a gap at the floor, is not a separation. Fire and smoke go over and under it.

Deck to deck

In an Klarvatten build the rated wall runs to the structure above and is sealed at both ends. It is the detail most often missed in conversions where a wall was built to the ceiling and no further.

Where Klarvatten homes usually need rated board

The four common places

Most rated drywall in Klarvatten houses is one of: the garage ceiling where living space sits above it, the garage-to-house wall, the furnace or mechanical room, and a legal-suite separation between dwelling units.

Renovations trigger it too

Finishing a basement, adding a suite or converting a garage often brings a separation into play that was not there before. If you are not sure whether your Klarvatten project triggers one, that is a question for the building official at permit stage, and we will tell you when we think you should ask.

Board thickness and why 5/8 is standard here

Not just thicker

Type X is 5/8 inch because the core needs that mass and the glass-fibre reinforcement to hold together as the gypsum calcines under heat.

The common error

Using 1/2 inch board in a rated Klarvatten assembly because it is what was on site. It looks identical once finished and it is not the tested assembly. Board arriving on site is checked against the specification rather than assumed.

How it works

Simple, clean, on schedule — Fire-Rated Drywall in Klarvatten Edmonton

Free quote

We come out to your Klarvatten Edmonton property, take a real look at the fire-rated drywall, and hand you a fixed price on the spot — no guessing, no vague ballpark. Every fire-rated drywall quote in Klarvatten Edmonton starts with an honest, on-site assessment.

Book a day

We pick a day that works for your schedule and show up on time, ready to start the fire-rated drywall in Klarvatten Edmonton. No back-and-forth rescheduling — once it's booked, our team is there.

The work

We keep the dust under control and protect your Klarvatten Edmonton home while we finish the fire-rated drywall to a clean, paint-ready standard. Floors covered, doors sealed off, and the site left tidy at the end of every day.

Walk it with you

We don't pack up till you've walked the finished fire-rated drywall with us and you're happy with the result in Klarvatten Edmonton. If anything needs a second look, we handle it before we call the job done.

Reviews

Rated by Edmonton Homeowners

★ ★ ★ ★ ★

Emplastrum Drywall is the fire-rated drywall contractor Klarvatten Edmonton trusts for repair, restoration and finishing — rated on Google by Edmonton homeowners.

Read the reviews, or leave your own after your fire-rated drywall project in Klarvatten Edmonton.

Read our reviews on Google

FAQ — Fire-Rated Drywall Klarvatten Edmonton

Fire-Rated Drywall Klarvatten Edmonton: your questions answered

Will it pass inspection in Klarvatten?: Yes — we install the correct Type X assembly and seal penetrations to spec so your Klarvatten separation passes inspection.
Do you handle the firestopping as well as the board?: We firestop the penetrations that fall within our scope and coordinate the sequence with the other trades so nothing is covered before it is sealed. Where a penetration belongs to another trade, we flag it rather than tape over it.
Can I use 1/2 inch board if that is what is on site?: Not in a rated assembly. Type X is 5/8 inch because the core needs that mass and reinforcement to hold together under heat. It looks identical once finished and it is not the tested assembly — we check board against the specification.
Can pot lights go in a rated ceiling?: Only with fixtures and firestopping suited to that assembly. A standard fixture cut into a rated Klarvatten ceiling breaks the separation. We coordinate the locations with your electrician so the penetrations are handled before we tape.
Do you install fire-rated drywall in Klarvatten?: Yes — fire-rated drywall in Klarvatten is part of our regular work, and we are usually booked within the week. We also cover Albany, Athlone, Baranow and Northwest.
My Klarvatten garage ceiling has board but the joints are open. Is that a problem?: Usually yes. Untaped joints are one of the most common reasons a garage separation is not complete, because the board looks installed. Often the fix is finishing the joints and sealing penetrations rather than replacing the ceiling.

Get Your Free Drywall Quote

Tell us about your project — we’ll get right back to you, 7 days a week. Prefer to call? (403) 829-8702.

Full Name / Company

Phone Number

Email Address

Area

Service Needed

I agree to be contacted by Emplastrum Drywall about my project by phone, text, or email.

No obligation. We never share your information.

📐 Plan Your Project

Estimate Your Drywall Materials

📐 Materials Calculator

How much do you need?

Enter your room size for a quick materials estimate.

Room length (ft)Room width (ft)Ceiling height (ft)Number of rooms Include ceilingSheet sizeCoats of paintCavity depthFraming spacingInsulation already there (in)Top up to (in)Stud spacingDoorsWindowsWaste allowance (%)

Estimate only — rounded up, based on standard coverage rates (drywall +10% waste; paint ~350 sq ft per gallon per coat; batt bundles by cavity depth, less a framing factor; studs at your chosen spacing plus waste). Product coverage varies by brand — confirm quantities before buying. Ask us about the right R-value for your project.

Rather we handle it? Get a free estimate →

Fire-Rated Drywall Klarvatten Edmonton

Fire-rated drywall in Klarvatten, installed to code